• Journal of Power System Engineering
• /
• v.6 no.4
• /
• pp.30-35
• /
• 2002

This study represents the effects of the material of the air cleaner on the performance in a 4-stroke spark-ignition engine for motorcycles. This study is mainly focused on the possibility of the adopting the STS wire mesh air cleaner of a S.I engine. For investigating the possibility of that, the engine power, the fuel consumption and the exhaust gas analysis were carried out for the synthetic fiber air cleaner and the different size of 200 mesh, 250 mesh, 300 mesh of STS wire mash air cleaner. As the results of this study, the performance of STS wire air cleaner was similar to the fiber air cleaner at 9000 rpm but 300 mesh of STS air cleaner had a high engine power and torque at 9500 rpm. In the case of the synthetic fiber air cleaner the concentration of CO was low at 6500 rpm and in the case of the 300 mesh in STS wire mesh air cleaner the concentration of HC was lowest at all experimental regions.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.2
• /
• pp.129-138
• /
• 2021

Due to the active progress in space programs for various types of ground and space missions, the high agile spacecraft maneuverability is also required. To meet the requirement of the given space missions, the Control Moment Gyros (CMG) for the alternatives of the classical reaction wheels can release the attitude maneuverability restrictions. In addition, the angular rates of the spacecraft is constrained due to the limited actuator characteristics. In this paper, a sliding mode control technique for the attitude control of the spacecraft equipped with the pyramid type of CSCMG(Constant Speed CMG) is designed, and the stability of the control system is guaranteed by using the Lyapunov stability theory. Finally, the control law proposed is analyized by numertical simulations.

• The Journal of Korea Robotics Society
• /
• v.17 no.2
• /
• pp.238-244
• /
• 2022

Maintenance works of offshore wind turbines could take a longer time, which causes the reduction of their energy production efficiency, than those of onshore wind turbines owing to severe offshore environment. Subsequently, preventive maintenance measures are required to increase the production efficiency. Thus, we proposed a wheel-based Underwater Pole Climbing Robot (UPCR) platform, which was aimed at the periodic inspection and maintenance of the substructures of the offshore wind turbines, with three advantages: high speed, good mobility and low power consumption. In the proposed platform, a self-locking system using a gripper module was adopted for preventing slippery problem and a dual configuration was chosen for moving on a branched structure. As a result, the proposed robot was able to continuously climb, preserve it's position at the pole without consuming energy, and move from the pole to the other branched pole. The results of this research show that the UPCR has basic moving capabilities required for the underwater work for the substructures of the offshore wind turbines.

• The Journal of the Convergence on Culture Technology
• /
• v.7 no.4
• /
• pp.801-806
• /
• 2021

Rail corrugation is continuously increasing due to the lack of maintenance regulations for the amount of rail irregularities. Rail corrugation is causing various problems, such as a decrease in ride comfort and an increase in the amount of track maintenance. In this paper, the effect of rail corrugation on the track force was analyzed by measuring the rail irregularities before and after rail grinding and the track measurements (dynamic wheel load, displacement, and acceleration) for the section where the rail corrugation occurred. In addition, it was experimentally proven that the rail grinding performed to reduce the corrugation of the rail was very effective in reducing the additional forces on the track.

• Tribology and Lubricants
• /
• v.39 no.2
• /
• pp.35-42
• /
• 2023

Bearing is a mechanical component that supports loads and transmits rotation. As the application of high-value-added products such as semiconductors, aviation, and robots have recently become diverse and more precise, an accurate bearing performance prediction and evaluation technology is required. Bearing performance evaluation can be divided into evaluations based on bearing theory and on numerical analysis. An evaluation based on numerical analysis is a technique that has been highlighted because the problems that remained unsolved owing to time problems can be solved through recent developments in computers. However, current studies have the disadvantage of not considering the essential changes over time and bearing rotation. In this study, bearing performance evaluation based on rigid body dynamic analysis considering rotation and load over time is performed. Rigid body dynamic analysis is performed for deep groove ball bearing to calculate the load applied by the ball. The reliability of the analysis is verified by comparing it with the results calculated using bearing theory. In addition, rigid body dynamic analysis is performed for automotive wheel bearings to calculate the contact angle and load applied by the ball for cases where axial load and radial load are applied, respectively. The effect of rotation and load over time is evaluated from these results.

• Structural Engineering and Mechanics
• /
• v.90 no.2
• /
• pp.177-187
• /
• 2024

In this study, compared two distinct estimation methods (stress charts and regression equations) proposed by the Indian road congress design guideline (IRC:58-2015) to determine flexural stress in Jointed Plain Concrete Pavement (JPCP). The occurrence of critical flexural stresses in pavement slabs is due to the combined effects of wheel loads and temperature. These stresses depend on various factors such as material properties of concrete, soil-subgrade strength, loading, and geometric properties of the slab. In order to account for the practical variability of these factors, critical edge stresses are determined using both methods and compared considering tied concrete shoulder. IRC:58 (2015) suggests, the stresses calculated by both the procedures should provide the same results. However, when these stresses are compared for the same configurations and same loading conditions, large variations are observed. The effect of tied concrete shoulder on reduction in critical edge stress is observed. Based on the study, certain important conclusions and recommendations are presented.

• Journal of Astronomy and Space Sciences
• /
• v.41 no.2
• /
• pp.121-138
• /
• 2024

Advances in solar-terrestrial physics are generally linked to the development of innovative new sensor technologies, affording us ever better sensitivity, higher resolution, and broader spectral response. Recent advances in low-noise InGaAs sensor technology have enabled the realization of low-light-level scientific imaging within the short-wave infrared (SWIR) region of the electromagnetic spectrum. This paper describes a new and highly sensitive ultra-wide angle imager that offers an expansion of auroral and airglow imaging capabilities into the SWIR spectral range of 900-1,700 nm. The imager has already proven successful in large-area remote sensing of mesospheric temperatures and in providing intensity maps showing the propagation and dissipation of atmospheric gravity waves and ripples. The addition of an automated filter wheel expands the range of applications of an already versatile SWIR detector. Several potential applications are proposed herein, with an emphasis on auroral science. The combined data from this type of instrument and other existing instrumentation holds a strong potential to further enhance our understanding of the geospace environment.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.12
• /
• pp.1037-1048
• /
• 2018

In this paper, we investigated the international guidelines and actual disposal maneuver cases to prepare KOMPSAT-2 post mission disposal. And then, disposal maneuver plan was established using current propellant of KOMPSAT-2 and verification was also performed to find out whether the international guidelines are satisfied. As a result, the lifetime of KOMPSAT-2 was 3.6 years when 45kg propellant was used to decrease perigee altitude to 300km. And if more than 14.5kg propellant consumed for same strategy, KOMPSAT-2 can satisfy the international guidelines. Finally, re-entry survivability analysis was performed and it represented that heat resistant objects, such as propellant tank and reaction wheel, could be survived but total ground casualty probability was less than international guidelines.

• Journal of the Korean Society for Railway
• /
• v.15 no.6
• /
• pp.543-549
• /
• 2012

This study describes the tail vibration reduction for the next generation high speed EMU(HEMU-430X). The model of 6 cars was generated and the calculation was performed using VAMPIRE(railway vehicle dynamic software). In view of ride characteristics, HEMU-430X was expected to sway at the tail because of the yaw damper direction. The lateral acceleration of vehicle body exceeded the criteria because of hunting. To reduce this hunting motion, some methods such as wheel profile change, the change of damping coefficient for the 2nd lateral damper, the damping coefficient change of yaw damper were tested, but had little effect. Finally, the yaw damper direction was changed and the tail vibration disappeared. In real running test, the tail vibration appeared at the speed of 150km/h and the yaw damper direction change made the vehicle stable at the speed of 300km/h. The maximum test speed of HEMU-430X is 430km/h. If the tail vibration appears at higher speed, some other methods in this study may be considered to reduce it.

• International Journal of Highway Engineering
• /
• v.10 no.2
• /
• pp.183-191
• /
• 2008

This study evaluated influence of the loading head dimension on characteristics of deformation strength ($S_D$) of asphalt mixtures. Kim test and Wheel tracking (WT) test were conducted to evaluate $S_D$ characteristics with relation to WT results for various mixtures. The $S_D$ values and coefficient of variation of $S_D$ values of r=10mm were smaller than those of r=10.5mm. It was also found that $S_D$ values obtained using r=10mm loading head showed high correlations with rut parameters of WT test. It was indicated that the aggregate size and radius (r) of round cut were statistically significant variables on $S_D$ at = 0.05 level in the analysis of variance. However, in interaction of r and aggregate size showed no significance within $10{\sim}19mm$ aggregate size at the same level. Therefore, it was concluded that the diameter (D) of 40mm and the bottom edge radius (r) of 10mm was suitable dimension of loading head for deformation strength test.