• Journal of the Korean Geosynthetics Society
• /
• v.15 no.4
• /
• pp.25-32
• /
• 2016

The two-dimensional (2D) analysis is widely used in geotechnical engineering for slope stability analysis assuming a plane-strain condition. It is implicitly assumed that the slip surface is infinitely wide, and thus three-dimensional (3D) end effects are negligible because of the infinite width of the slide mass. The majority of work on this subject suggests that the 2D factor of safety is conservative (i.e. lower than the 'true' 3D factor of safety). Recently, the 3D finite element method (FEM) became more attractive due to the progress of computational tools including the computer hardware and software. This paper presents the numerical analyses on rotational mode and translational mode slopes using the 2D and 3D FEM as well as 2D limit equilibrium methods (LEM). The results of the parametric study on the slope stability due to mesh size, dilatency angle, boundary conditions, stress history and model dimensions change are analysed. The analysis showed that the factor of safety in 3D analysis is always higher than that in the 2D analysis and the discrepancy of the slope width in W direction on the factor of safety is ignored if the roller type of W direction conditions is applied.

• Journal of IKEEE
• /
• v.2 no.1 s.2
• /
• pp.160-165
• /
• 1998

This paper describes a method for field analysis inside the flat-type brushless DC motor using 2-D field simulator. Rigorous field analysis entail 3-D analysis. However, this analysis is not often appropriate for system designs because of the time and cost involved. For field analysis in this study, the 3-D problem is reduced to a 2-D boundary value problem by introducing a cylindrical cutting plane at the mean radius of the magnets. Independent of sizes and shapes of systems, the exact 2-D field results can be obtained with reasonable predictability.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.4
• /
• pp.29-39
• /
• 2016

This paper presents the results of 2D and 3D finite element simulations conducted to analyze the effects of excavation depth (H), excavation width (L), and ground condition on the behavior of anchored earth retaining wall in inclined ground layers. The results of numerical analyses are compared with those of the site instrumentation analyses. Based on the results obtained, it appeared that 2D numerical analysis tends to overestimate the horizontal displacement of retaining wall compared to the 3D numerical analysis. When the excavation depth is deeper than 20m, it is found that 2D and 3D numerical analysis results of excavation work in soil ground condition are more different from the results in rock ground condition. For an accurate 3D numerical analysis, applying 3D mesh which has an excavation width twice longer than excavation depth is recommended. Consequently, 3D numerical analysis may be able to offer significantly better predictions of movement than 2D analysis.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.5
• /
• pp.129-138
• /
• 2006

Composite deck plate using a pre-assembled re-bar truss for slab with corrugated zinc galvanized sheet iron at manufactory, is given the improvement on design, manufacture, and performance for construction work of cast-in-place reinforced concrete slab by enabling to cast concrete directly without the form work. There are two methods in analyzing composite deck : Simplified 2D analysis and 3D analysis. Although simplified 2D analysis is being used up to date, the use of 3D analysis, allowing for the vierendeel behavior of composite deck by real configuration correlating to bar reducing, is demanded. To compare the simplified 2D analysis applied to allowable stress design with 3D analysis applied to limit state design, 8 specimen are manufactured. Main variables include the depth of slab, the length of span, the diameter of bottom bar and lattice bar, and the presence of corrugated zinc galvanized sheet iron. The comparison from the experimental result and analytical result indicates that applying of simplified 2D analysis is possible for the use of D10 with bottom bar. However, it is more reasonable to apply 3D analysis which allows to indicate vierendeel behavior considered the real configuration.

• Journal of the Korean GEO-environmental Society
• /
• v.20 no.10
• /
• pp.5-14
• /
• 2019

Recently, earthquakes have occurred in our country and seismic stability of high-rise buildings in large cities is being a growing interest and thus the related studies have been increased. Also the grounds are considered indirectly in most of seismic designs and analyses and seismic researches based on 3D dynamic analysis are insufficient. In this study, therefore, 2D and 3D dynamic analyses were performed based on the SSI complete model including grounds and the behavior was compared and analyzed. For dynamic modeling, linear time history analyses were performed by using MIDAS GTS NX. For this purpose, a high-rise building was assumed to be constructed on top of the bedrock and surrounded by a surface layer. A sensitivity analysis was performed with the selected parameters. The dynamic behavior was compared and analyzed in terms of horizontal displacements, drift ratios, bending stresses, and weak parts. In most cases, 2D dynamic behavior was calculated to be larger than 3D's and thus it shows more conservative results with increasing number and size of weak parts.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.48-48
• /
• 2017

도시지역에서는 이상강우, 돌발홍수와 더불어 급속한 도시화에 따라 침수 발생의 위험성이 증가하고 있다. 지자체에서는 빗물펌프장, 지하저류조 등을 이용하여 적극적으로 침수대책을 강구하고 있지만, 저지대 침수피해는 계속적으로 발생하고 있다. 2013년 7월 서울 경기북부 강원영서에 발생한 집중호우로 1명이 사망하고 피해액은 94,036백만원이 발생하였다. 춘천시 효자동 저지대지역의 주택침수는 인근 하천의 수위가 높아져 내수배제 및 하수도 처리 능력이 부족하여 침수가 발생하였다. 2014년 8월 경남지역에 발생한 집중호우로 2명 사망하였고, 피해액은 134,158백만원에 이르렀으며, 도시화 토지피복변화로 인한 홍수량이 증가하여 피해가 가중되었다. 이에 따라 도시 내 정확한 도시유출 및 침수해석을 통하여 과거 침수양상을 재현하고 앞으로 발생할 수 있는 침수피해를 방지할 수 있도록 침수 예 경보 시스템을 개발하여 도시침수에 대비하고 도시주민들의 인명과 재산피해를 경감하는데 그 목적이 있다. 이를 위해 도시지역의 관망해석에 적합한 모형을 선택하여야 하며, 그 모형의 매개변수를 결정하여야 한다. 도시유출해석 및 관망해석을 위하여 SWMM 모형을 선정해서 유역분할조건, 매개변수에 대한 최적 검정과정을 제시하여, 1D-2D 연계모형을 통해서 침수지역예측의 정확도를 증대시키고자 한다. 본 연구에서는 서울시 강남역 주변 일대의 5개 배수분구을 대상으로 도시유출해석을 위한 최적화 모의를 위하여 1D-2D모형의 연계해석하였다. 실제 강우사상을 적용하여 매개변수와 소유역 개수를 달리하여 자동최적화기법인 PEST를 이용하여 최적인자를 도출하여, 실제 배수맨홀의 수위관측 자료를 이용하여 비교 보정을 하였다. 도시유출해석뿐만 아니라 내수침수시의 최적인자 도출을 위해 2차원 범람해석을 통하여 NDMS 자료를 이용하여 비교 보정을 한 뒤 다른 강우사상을 이용하여 검증을 하여 도시침수 해석의 정확도를 개선을 위한 최적인자들을 검토하였다.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.20 no.4
• /
• pp.363-371
• /
• 2008

The aim of this study is to compare the numerical results obtained by 2-D and 3-D models which are used to examine the wave field around a permeable submerged breakwater. At first, the numerical model, which is able to consider the flow through a porous medium with inertial, laminar and turbulent resistance terms and determine the eddy viscosity with LES turbulent model, is used and validated by comparing with existing experimental data. And then, the numerical test on the wave field around a permeable submerged breakwater is performed. It is revealed from the numerical results that, at the onshore side of the submerged breakwater, the wave height by 2-D analysis is higher than that by 3-D analysis. Also, the time-averaged mean flow around a submerged breakwater is discussed in detail.

• Journal of Aerospace System Engineering
• /
• v.18 no.4
• /
• pp.10-17
• /
• 2024

Solar-powered unmanned aerial vehicles(SPUAV), which are being actively developed domestically and internationally, generally feature high aspect ratio(AR) wings. These high AR wings necessitate a lightweight design as their weight increases, rendering them susceptible to flutter. Consequently, flutter analysis is critical from the initial design phase. Typically, flutter analysis is conducted using a standard section wing or more precisely through a 3D model. However, due to the extended analysis time required by 3D models, this study opts for a 2D aircraft model. The 2D model computes faster than the 3D model and intuitively secures the flutter boundary. In this study, a structural/aerodynamic force model of the 2D aircraft was established, and the findings were compared with those from a 3D half model. The results showed that the flutter analysis between the 2D model and the 3D half model was similar, within about a 3% margin, thus validating the proposed 2D model's effectiveness.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.28 no.3
• /
• pp.283-291
• /
• 2015

In this paper, the two-dimensional(2D) and three-dimensional(3D) analyses have been performed in order to evaluate the structural integrities and compare 2D and 3D results for nozzles attached to cylindrical shells. Three nozzles, which are currently used in the nuclear power plant, are chosen to evaluate the structural integrities, and each nozzle is subjected to internal pressure, temperature variation and external loads. It is found that the 2D analysis for internal pressure should be performed with a factor of more than 1.5 or a stress concentration factor; 2D and 3D analysis results for temperature variation are almost similar to each other regardless of cladding; and the analysis results for external loads by WRC Bulletin 297 are more conservative than the 3D analysis results.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.5
• /
• pp.1049-1054
• /
• 2013

In this paper, two-dimensional(2-D) Finite Difference Time Domain(FDTD) method using the domain decomposition method is proposed. We calculated the electromagnetic scattering field of a two dimensional rectangular Perfect Electric Conductor(PEC) structure using the 2-D FDTD method with Schur complement method as a domain decomposition method. Four domain decomposition and eight domain decomposition are applied for the analysis of the proposed structure. To validate the simulation results, the general 2-D FDTD algorithm for the total domain are applied to the same structure and the results show good agreement with the 2-D FDTD using the domain decomposition method.