• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.17 no.4
• /
• pp.79-90
• /
• 2021

This paper presents a study to reduce the effect of blast pressure on the blast valves installed in protection tunnels, where the shape of the tunnel entrance and the blast pocket is optimized based on the predetermined basic shape of the protective tunnels. The reliability of the numerical tunnel models was examined by performing analyses of mesh convergence and overpressure stability and with comparison to the data in blast-load design charts in UFC 3-340-02 (DoD, 2008). An optimal mesh size and a stabilized distance of overpressure were proposed, and the numerical results were validated based on the UFC data. A parametric study to reduce the blast overpressures in tunnel was conducted using the validated numerical model. Analysis was performed applying 1) the entrance slope of 90, 75, 60, and 45 degrees, 2) two blast pockets with the depth 0.5, 1.0, and 1.5 times the tunnel width, 3) the three types of curved back walls of the blast pockets, and 4) two types of the upper and lower surfaces of the blast pockets to the reference tunnel model. An optimal solution by combining the analysis results of the tunnel entrance shape, the depth of the blast pockets, and the upper and lower parts of the blast pockets was provided in comparison to the reference tunnel model. The blast overpressures using the proposed tunnel shape have been reduced effectively.

• Food Engineering Progress
• /
• v.21 no.3
• /
• pp.267-272
• /
• 2017

To improve dispersibility of cereal powder without additives, granulation of cereal powder was conducted using fluidized-bed granulator. Operation condition was sample 300 g, internal temperature $40^{\circ}C$, ventilation speed $30-90m^3/h$, inlet temperature $90^{\circ}C$ and spray pressure 2.5 bar. The amount of distilled water (20-45%) as binder, granulation time (10-15 min) and drying time (3-10 min) were controlled. Mean diameter over volume (Brouckere mean, $D_{4,3}$) was increased from $123{\mu}m$ to $263{\mu}m$ and dispersibility was improved from 73% to 92.25% at experiment conditions. Wettability (wetting time) was drastically decreased from 5,000 second to 7 second. Granulation of cereal powder did not affect sinkability and mean diameter over volume as wet analysis was about the same between raw and granulated cereals. Such phenomenon means that granulation with only water as binder enables cereal powder to disperse in water or milk without rapid sedimentation.

• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.5
• /
• pp.477-486
• /
• 2008

Numerical analysis for slamming impact phenomena has been carried out when 2-dimensional wedge shaped structure with finite deadrise angles enter the free surface by using a commertial CFD code, FLUENT. Fluid is assumed incompressible and entry speed of the structure is kept constant. Geo-reconstruct scheme (or PLIC-VOF scheme) is used for the tracking of the deforming free surface. User defined function of 6 degrees of freedom motion and moving dynamic mesh option are used for the expression of the downward motion of the structure and deforming of unstructured meshes adjacent to the structure. The magnitude and the location of impact pressure and the total drag force which is the summation of pressures distributed at the bottom of the structure are analyzed. Results of the analysis show good agreement with the results of similarity solution, asymptotic solution and the solution of BEM.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.185-185
• /
• 2011

Mapping of artificial levee lines, one of major tasks in river zone mapping, is critical to prevention of river flood, protection of environments and eco systems in river zones. Thus, mapping of artificial levee lines is essential for management and development of river zones. Coastal mapping including river zone mapping has been historically carried out using surveying technologies. Photogrammetry, one of the surveying technologies, is recently used technology for national river zone mapping in Korea. Airborne laser scanning has been used in most advanced countries for coastal mapping due to its ability to penetrate shallow water and its high vertical accuracy. Due to these advantages, use of LiDAR data in coastal mapping is efficient for monitoring and predicting significant topographic change in river zones. This paper introduces a method for construction of a 3D artificial levee line using a set of LiDAR points that uses normal vectors. Multiple steps are involved in this method. First, a 2.5-dimensional Delaunay triangle mesh is generated based on three nearest-neighbor points in the LiDAR data. Second, a median filtering is applied to minimize noise. Third, edge selection algorithms are applied to extract break edges from a Delaunay triangle mesh using two normal vectors. In this research, two methods for edge selection algorithms using hypothesis testing are used to extract break edges. Fourth, intersection edges which are extracted using both methods at the same range are selected as the intersection edge group. Fifth, among intersection edge group, some linear feature edges which are not suitable to compose a levee line are removed as much as possible considering vertical distance, slope and connectivity of an edge. Sixth, with all line segments which are suitable to constitute a levee line, one river levee line segment is connected to another river levee line segment with the end points of both river levee line segments located nearest horizontally and vertically to each other. After linkage of all the river levee line segments, the initial river levee line is generated. Since the initial river levee line consists of the LiDAR points, the pattern of the initial river levee line is being zigzag along the river levee. Thus, for the last step, a algorithm for smoothing the initial river levee line is applied to fit the initial river levee line into the reference line, and the final 3D river levee line is constructed. After the algorithm is completed, the proposed algorithm is applied to construct the 3D river levee line in Zng-San levee nearby Ham-Ahn Bo in Nak-Dong river. Statistical results show that the constructed river levee line generated using a proposed method has high accuracy in comparison to the ground truth. This paper shows that use of LiDAR data for construction of the 3D river levee line for river zone mapping is useful and efficient; and, as a result, it can be replaced with ground surveying method for construction of the 3D river levee line.

• Journal of Korean Society for Atmospheric Environment
• /
• v.12 no.3
• /
• pp.315-322
• /
• 1996

Recently, hospital acquired infections have an increase interest as a public problems, which are caused of indoor pollutants in hospital. Microorganisms, ethylene oxide, formaldehyde, and anesthetic gases are main hazardous pollutants in hospital. The possible pathways of the infection are a respiratory channel as well as a blood channel. The blood channel is concerned since these pollutants might be dissolved into the Ringer's solution. The objective of this research was to evaluate the removal efficiencies of adsorption trap for formaldehyde and microorganisms as indoor pollutants which permeated into the Ringer's solution. Dissolved formaldehyde in the solution was increased with the injection dose time. The amount of dissolved formaldehyde was 67.5 $\pm$ 9.5% in Ringer's solution when injection dose time was controlled about 7hrs. An adsorption trap was designed for preventing formaldehyde and microorganisms to be permeated into Ringer's solution. The adsorption trap was packed with 0.4g of active carbon (60/80 mesh) in a sterilized plastic tube (7.79 cm length, 0.46 cm i.d.) and both ends were packed with glass wool. Devised infusion set equipped with the adsorption trap showed 99.9% of removal efficiency for formaldehyde. Microorganism numbers detected on sterilized water for injection and 5% dextrose infusion used in the hospital were 2,695 $\times 10^3$ cells/l and 4,190 $\times 10^3$ cells/l, respectively. Removal efficiency by the adsorption trap was 92.3 $\pm$ 8.5% as for microorgnisms.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.164-164
• /
• 2017

해양환경 중 많이 사용되는 철강재료들은 그 가혹한 부식환경에 대응하기 위하여 일반적으로 피복 도장방식법이나 음극방식법이 적용되고 있다. 여기서 음극방식법은 선박 및 해양구조물의 해중부 부식에 대해 가장 효과적인 방식법으로 알려져 있다. 한편, 이와 같이 해수 중 철강재에 음극방식을 적용할 경우, 피방식체인 그 강재 표면에 해수 중 용존된 산소의 음극환원 반응이 일어나며 국부적인 알카리 표면 조건을 형성시켜 $Mg(OH)_2$와 $CaCO_3$의 막을 석출시킨다. 이와같이 음극방식 중 형성된 전착물은 방식해야 될 표면적을 감소시켜 방식전류밀도를 감소시키는 효과가 있는 것으로 보고되고 있다. 이렇게 석출된 전착물은 음극표면에 부분적으로 형성되고, 여러 가지 환경 조건 등의 영향을 받아 그 피막의 형성 정도도 가늠하기 어렵기 때문에 음극방식 설계 시 그 정도에 따른 영향을 고려-반영하기가 곤란하다. 또한 이 전착물은 그 형성 메커니즘에 관한 해석이나 강도, 균일한 밀착성, 장기적인 방식효과 및 효율성 등이 아직 충분히 입증되어 있지 않은 실정에 있다. 따라서 본 연구에서는 해수 중 다양한 전착 프로세스에 의해 제작된 전착물의 기간별, 도장코팅 종류별 특성변화를 분석 및 평가하고, 전착물에 의한 희생양극 소모전류 변화 측정 분석을 통해 전착막을 균일하고 치밀하게 형성시키기 위한 최적의 조건을 찾고자 하였다. 또한 석출속도, 밀착성 및 내식특성을 향상시키기 위해 해수 중 기체를 용해시켜 제작한 막의 특성을 분석-평가하였다. 본 연구에 사용된 강 기판은 일반구조용강(KS D 3503, SS400)으로 ${\varnothing}42.7{\times}1,000mm{\times}4.0t$의 형상으로 제작하였다. 인가된 전류밀도는 1, 3 및 $5A/m^2$이고 도장 코팅 종류별 전착 석출물의 형성차이 비교 분석을 위한 실험은 선박 및 해양구조물에 많이 사용되는 Universal Epoxy 도료 2종을 선정하여 진행하였다. 또한 Steel Wire Mesh의 영향을 알아보기 위해 Mesh를 설치하여 실험을 진행하였다. 기간별-도장 종류별 외관관찰, 전착물의 두께 측정, SEM, EDS 및 XRD를 통해 막의 모폴로지, 조성원소 및 결정구조를 분석하였으며, 전착물의 내식성과 내구성을 평가하기 위해 테이핑 테스트(Taping Test) 및 전기화학적 양극분극 시험을 실시하였다. 희생양극 소모율에 대한 전착물의 영향을 확인하기 위해 외부전원을 인가하여 전착 피막을 형성시킨 강 기판에 희생양극을 연결하여 희생양극 소모효율 측정 시험을 진행하였다. 전착물의 석출량은 시간 및 전류밀도의 증가에 따라 비례하여 증가하였으며, 음극전류 인가 시 금속과 용액 계면 사이의 확산층에서 발생한 $OH^-$ 이온으로 인해 금속과 용액 계면 사이 pH가 부분적으로 증가하여 $Mg(OH)_2$ 화합물이 많이 생성되는 것으로 확인되었다. 또한 Mesh의 부착으로 평활하지 않게 형성된 미세한 굴곡구조 및 표면적 증가로 인하여 단계적으로 피복되는데 필요한 시간이 지연되면서 $CaCO_3$에 비해 $Mg(OH)_2$ 화합물이 상대적으로 증가한 것으로 사료된다. $CaCO_3$(Aragonite) 구조는 견고한 피막으로 치밀하고 화학적 친화력이 높아 우수한 밀착성을 보였으며 전착물의 영향으로 양극 전류가 감소하였고, 이로인해 방식전류 절감효과를 얻을 수 있을 것으로 기대된다.

• Journal of the Korea Computer Industry Society
• /
• v.5 no.5
• /
• pp.737-746
• /
• 2004

Two-channel multiwavelet system is investigated for image compression application in this paper. Generally, multiwavelets are known for their superb capability of compressing non-stationary signals like voice. However, multivavelet system have a critical problem in processing and compressing image data due to mesh-grid visual artifacts. In our two-channel multiwavelet system we have investigated incorporation of pre and post filtering to the multiwavelet transform and compression system for alleviating those ingerent visual artifacts due to multiwavelet effect. In addition, to quantify the image data compression performance of proposed multiwavelet system, computer simulations have been performed using various image data. For bit allocation and quantization, the Lagrange multiplier technique considering data rate vs. distortion rate along with a nonlinear companding method are applied equallly to all systems considered, here. The simulation results have yielded 1 ~ 2 dB compression enhancement over the scalar savelet systems. If the more advanced compression methods like SPIHT and run-length channel coding were adopted for the proposed multiwavelet system, a much higher compression gain could be obtained.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.3
• /
• pp.82-87
• /
• 2013

In this work, the 1L grade integrated metal DOC/DPF filter that can install in engine manifold position was developed to investigate the effect of platinum-coating amount of filter on the improvement of filter activation temperature and reduction of particulate matter (PM). This filter was installed in 2.9L CI engine which meets the EURO-4 emission regulation. Tests for PM reduction efficiency of filter were conducted under ND-13 mode with full-load test condition. It was revealed that the time to reach the activation temperature of metal filter ($280^{\circ}C$) was shorter as the amount of platinum-coating increased. This short activation time can be helpful for the reduction of CO and HC emissions during cold start condition. At the same time, PM reduced as the coating amount increased. The reduction percentage of $DOC_{40}$, $DOC_{20}$, and $DOC_0$ were 96.7% (2.34 mg/kW'h), 95.1% (3.47 mg/kW'h), and 94.5% (3.69 mg/kW'h) compared to previous result (71.4 mg/kW'h), respectively.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.32 no.3
• /
• pp.257-265
• /
• 1996

The combined hydroacoustic and bottom trawl surveys were conducted in the Cheju southeastern area by the training ship "KAYA" belong to Pukyong National University in July 1995 and the traning ship "NAGASAKI MARl]" belong to Nagasaki University in April 1994, respectively. The main purpose of the investigations was to provide the basic data for the management and the biomass estimation of commercially important demersal fish stocks in this area. Fish samples were collected by bottom trawling from 10 trawl stations randomly selected in the survey area, and the species and length compositions of trawl catches were examined. The fish school target strength for demersal fish aggregations was related to the catchability of trawl net with a 90 mm mesh codend. The most abundant species in the 1995 trawl stations were Japanese flying squid, sword tip squid and red horsehead and that of the 1994 trawl stations Japanese flying squid and blackmouth goosefish. The average weight per cubic meter of trawl catches collected by bottom trawling in the Cheju southeastern area were $1.0791{\times}lO^-4$kg/$m^3$ in the 1994 survey area and $1.3636{\times}lO^-4$kg/$m^3$ in the 1995 survey area, respectively. The catch data by cover net suggest that the efficiency of trawl net could affect the weight normalized target strength values for demersal fish aggregations. That is, the average target strength per unit of weight dropped from - 33.1 dB/kg using the total catch by codend and cover net to - 30.5 dB/kg using only the catch data by codend, and a change of2.6 dB/kg was observed.ange of2.6 dB/kg was observed.

• Steel and Composite Structures
• /
• v.12 no.3
• /
• pp.249-260
• /
• 2012

In this study, stress and deflection behaviours of T-type welding joint applied to HE200M steel beam and column were investigated in finite element method (FEM) under different distributed loads. In the 3D-FEM modelling, glue option was used to contact between steel materials and weld nuggets. Geometrical model was designed as 3-dimensional solid in ANSYS software program. After that, homogeneous, linear and isotropic properties were used to design to materials of model. Solid-92 having 3-dimensional, 4 faced and 10-noded was selected as element type. In consequence of mesh operation, elements of 13285 and nodes of 28086 were occurred. Load distribution was applied to top surface of steel beam to determine behaviours of stress and deflection. As a result of FEM analysis applied with the loads of 55,000 N, 110,000 N and 220,000 N, maximum values were obtained as 116 N/$mm^2$, 232 N/$mm^2$ and 465 N/$mm^2$ for stress and obtainedas 1,083 mm, 2,166 mm and 4.332 mm for deflection, respectively. When modelling results and classical calculation values were compared, it was obtained difference of 10 % for stress values and 2.5% for deflection values.