• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.10
• /
• pp.159-168
• /
• 2012

In this paper, a W-band single-chip receiver MMIC for FMCW(Frequency-modulated continuous-wave) radar is presented using $0.15{\mu}m$ GaAs pHEMT technology. The receiver MMIC consists of a 4-stage low noise amplifier(LNA), a down-converting mixer and a 3-stage LO buffer amplifier. The LNA is designed to exhibit a low noise figure and high linearity. A resistive mixer is adopted as a down-converting mixer in order to obtain high linearity and low noise performance at low IF. An additional LO buffer amplifier is also demonstrated to reduce the required LO power of the W-band mixer. The fabricated W-band single-chip receiver MMIC shows an excellent performance such as a conversion gain of 6.2 dB, a noise figure of 5.0 dB and input 1-dB compression point($P_{1dB,in}$) of -12.8 dBm, at the RF frequency of $f_0$ GHz, LO input power of -1 dBm and IF frequency of 100 MHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.11
• /
• pp.1183-1189
• /
• 2014

The accuracy of the resistive-sheet technique in calculating the RCS(Radar Cross Section) of a deciduous leaf is examined in this paper for various thicknesses and dielectric constants, and a range of thicknesses for the resistive sheet technique is proposed. At first, a leaf was assumed to be a lossy dielectric disk, and the dielectric disk was again assumed to be a resistive sheet with an appropriate resistivity for a given thickness, a dielectric constant, and a frequency. Then, the RCS of the leaf was computed using the physical optics(PO) method, and was compared with the calculation results of a numerical analysis: i.e., a commercial tool based on the FEM (Finite Element Method) technique. It was shown that the error increases as the thickness increases. The error was 0.1 dB, for example, when the thickness is 1.2 mm and 3.7 dB when the thickness is 3 mm with a dielectric constant of(21.4, 9.7) at 9.6 GHz. It was also found that the error decreases as the dielectric constant increases. This study will be very useful for calculating the scattering characteristics of numerous leaves in a vegetation canopy for estimating its radar backscatter using scattering model.

• Composites Research
• /
• v.27 no.5
• /
• pp.190-195
• /
• 2014

This paper predicts the complex permittivity of MWNT added epoxy depending on agglomeration by numerical analysis. 1wt% MWNT added epoxy specimen is prepared using 3-roll-mill method and its complex permittivity is measured in X-band (8.2~12.4 GHz) using freespace measurement system. The analytic model is comprised of cube epoxy and perfect sphere agglomeration. The complex permittivity of the agglomeration model is predicted by complex permittivity mixing rule using the measured complex permittivity of epoxy and 1 wt% MWNT added epoxy. Commercial electromagnetic analysis software, CST, is used to obtain S-parameter of the analytic model and MATLAB code is used to calculate complex permittivity from the S-parameter. It is confirmed that the complex permittivity increases when the agglomeration size decreases.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.05a
• /
• pp.130-133
• /
• 2002

As a society advances, an aging phenomenon and many diseases which did not exist in old times are happening. Especially, in case of the aged patient, because we cant know the time the condition of the patients health become worse, the study of the Tele-information system has been actively carried out by the necessity of a persistent observation. A ECG signal a kind of a vital signals has been widely used to the medical information system as an usual clinical diagnosis for the patients who possess heart diseases. BlueTooth is a close range wireless communication technology which uses a wireless frequency 2.4GHz and has a high trust and self - error correction technology according to a low power consumption quality and a high-speed frequency hopping. This makes get a high trust concerning a data transmission than an existing modem. In addition, though wireless modem is restricted by a minimal of a wireless terminal, It will be possible to coincide with the function of the portable with the low power consumption quality by using Bluetooth. And as the system on a chip of module progresses, the possibility of the small size is present According to this, Bluetooth module transmits the medical information, which is input from the outside among the operations that use the Bluetooth to the Bluetooth module that is connected the host PC. And the system that the host PC transmits the medical information from the connected Bluetooth module to the Internet has once embedded. this study let the host PC embedded in advance of the existing system and transmit the medical information by the addition of the Tcp/Ip protocol stark under all embedded environments to internet.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.6C
• /
• pp.476-482
• /
• 2012

In this paper, we analyze and compare several co-channel interference mitigation algorithms for WBAN application in 2.4 GHz ISM frequency bands. ML (Maximum Likelihood), OC (Optimal Combining) and MMSE (Minimum Mean Square Error) has been considered for the possible techniques for interference cancellation in view of the trade off between the performance and the complexity of implementation. Based on the channel model of IEEE 802.15.6 standard, simulation results show that ML and OC attains the lower BER performance than that of MMSE if we assume the perfect channel estimation. But, ML and OC have the additional requirement of implementation for his own and other users's channel estimation process, hence, besides the BER performance, the complexity of implementation and the sensitivity to channel estimation error should be considered since it requires the simple and small sized equipment for WBAN system application. In addition, the gap of detection BER performance between ML, OC and MMSE is much decreased under the imperfect channel estimation if we adopt real channel estimation process, therefore, in order to apply to WBAN system, the trade off between the BER performance and complexity of implemetation should be seriously considered to decide the best co-channel interference cancellation for WBAN system application.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.5
• /
• pp.775-782
• /
• 2022

In this paper, a novel small-diameter cylindrical post capacitor inserted into an evanescent-mode rectangular waveguide (EMRWG) is proposed for easier tuning. In order to feed the EMRWG, the proposed structure uses a single ridge rectangular waveguide with the same width and height as the waveguide at the input and output ends. The inserted post capacitor are made up a circular groove formed in the center of the lower part of the broad wall of the EMRWG, and a concentric cylindrical post inserted into the upper part. First, the equivalent circuit model for the proposed structure is presented. When the EMRWG and the single ridge waveguide are combined, the joint susceptance and the turns ratio of the ideal transformer are calculated by two simulations using HFSS (3d fullwave simulator, Ansoft Co.) respectively. The susceptance and resonance characteristics of the inserted post were analyzed by using the obtained parameters and the characteristics of the EMRWG. A 2-post filter with a center frequency of 4.5 GHz and a bandwidth of 170 MHz was designed using a WR-90 waveguide, and the simulation results by using the HFSS and CST, equivalent circuit model were in good agreement.

• Journal of the Korean Ceramic Society
• /
• v.40 no.4
• /
• pp.333-339
• /
• 2003

Ba (Co$_{1}$ 3/Nb$_{2}$ 3/)O$_3$(BCN) has a 1:2 ordered hexagonal structure. Q-value of BCN increased with increasing sintering temperature however, it significantly decreased when the sintering temperature exceeded 140$0^{\circ}C$ Ba (Co$_{1}$ 3/Nb$_{2}$ 3/)O$_3$(BZN) has the 1:2 ordered hexagonal structure and the degree of the 1 : 2 ordering decreased with the increase of the sintering temperature. The Q value of the BZN increased with increasing the sintering temperature and BZN sintered at 140$0^{\circ}C$ for 6h has a maximum Q-value. For (1-x) Ba (Co$_{1}$ 3/Nb$_{2}$ 3/)O$_3$-zBa(Zn$_{1}$ 3/Nb$_{2}$ 3/)O$_3$[(1-x)BCN-xBZN] ceramics the 1:2 ordered hexagonal structure was observed in the specimens with x$\leq$0.3 and the BaNb$_{6}$ O$^{16}$ second phase was found in the specimens with x$\geq$0.6. Grain Growth, which is rotated to the BaNb$_{6}$ O$^{16}$ second phase occurred in the specimens with x$\geq$ 0.5. In this work, the excellent microwave dielectric properties of $\tau$r=0.0 ppm/$^{\circ}C$$\varepsilon$r=34.5 and Q,$\times$f=97000GHz sere obtained for the 0.7BCV-0.3BZN ceramics sintered at 1400$0^{\circ}C$ for 20h.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.347-348
• /
• 2001

마이크로스트립 안테나가 가지는 가장 큰 단점인 협대역 특성을 개선하기 위해 그 동안 수많은 연 구와 방법들이 제안되었는데 특히 원형편파 안테나는 임피던스 대역폭 외에 축비 대역폭까지도 고려 되어야 하므로 더욱 심화된 협대역의 특성을 가지게 되어 설계에 많은 어려움이 있었다. 일반적으로 원형편파 마이크로스트립 안테나를 설계하는 방법 중 급전 구조면에서는 크게 단일 급전 방식과 하이 브리드 형태의 급전방식이 있다. 단일 급전 방식의 원형편파 안테나는 구조가 간단하고y 제작이 간편 하며, 안테나의 물리적 크기를 줄일 수 있어 배열시 장점이 있으나 구조의 특성상 협대역의 축비 대역 폭을 가지며I 하이브리드 급전 원형편파 안테나는 구조가 복잡하고, 제작이 어려우며, 안테나의 물리적 크기가 커진다는 단점이 있으나 광대역의 축비 대역폭을 가진다. 따라서 원형편파 안테나의 설계시 축 비 대역폭과 안테나의 물리적 크기 간의 trade-off를 고려하여야한다. 최근에는 이를 고려한 단일 급전 을 이용하면서도 개선된 축비특성올 얻을 수 있도록 십자개구 개구를 통해 두 개의 직교 모드를 방사 패치에 급전하는 구조가 제안되기도 하였다. 하지만 이는 일반적인 단일 급전 방식보다 개선된 축비 대역폭을 얻을 수 있었으나 중심주파수에서 2.5%에 불과하였다. 본 논문에서는 단일 급전 십자개구 결합 방식이 가지는 협대역의 축비 대역폭을 개선하기 위해 단 일 급전으로 하이브리드 급전의 효과를 가져올 수 있는 직렬 급전 십자개구 결합 마이크로스트립 안 테나를 제안하였으며, 기존에 발표된 단일 급전 십자개구 결합 안테나와의 축비 대역폭, 이득, 방사패 턴, 그리고 임피던스 대역폭 둥과 비교하여 개선된 특성을 제시하고 제안된 안테나의 타당성을 보였 다. 실제로 2.4GHz의 주파수에서 제안한 직렬 급전 십자개구 결합 단일 마이크로스트립 안테나의 측 정결과 기존에 연구된 안테나보다 약 2배정도 증가된 4.6%의 축비 대역폭, 10%의 임피던스 대역폭 (VSWR<1.5), 그리고 8.2dBi의 최대이득 특성을 확인할 수 있었으며, 이를 바탕으로 시권셜 로테이션 기법올 사용한 $2\times2$ 배열 안테나는 17.5%의 축비 대역폭, 20.8%의 임피던스 대역폭(VSWR<1.5), 그리 고 12.5dBi의 최대이득을 얻을 수 있었다. 이에 해당하는 제안된 단일 안태나와 $2\times2$ 배열 안테나의 구조, 측정된 축비 대역폭 및 이득특성, 그리고 입력 반사손실을 그림 I, 2, 3에 각각 나타내었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.105-105
• /
• 2000

현재 급격히발전하는 이동통신기술로 미루어 보아 앞으로는 모든 정보통신이 무선통신으로 이루어질 것이다. 그런데 무선통신은 이동성과 대용량의 정보전송에 초점을 맞추어 발전하고 있다. 많은 정보량을 전달하기 위해서 현재 사용되는 주파수 대역보다 고주파의 전파가 사용되어야 한다. 또한 이동성을 향상시키기 위해서는 통신기기의 소형화를 이루어야 하고 그러기 위해서 궁극적으로 모든 소자를 하나의 칩(chip)으로 집적화하는 것이 필요하다. 따라서 벌크상태로 사용되고 있는 유전체 공진기를 소형화, 즉 박막화해야만 한다. 결국 유전체 박막의 마이크로파 대역에서의 유전특성을 연구하고 그 특성을 향상시켜야만 한다. 통신기기에서 사용되는 유전체 공진기는 소형화를 위해 높은 유전율과 낮은 유전손실(tan$\delta$), 즉 높은 품질계수 (Q)를 가져야 한다. 마이크로파 대역에서 사용되고 있는 유전체 중에서 TiO2는 벌크 상태의 rutile 상에서 100정도의 높은 유전율과, 4 GHz에서 10,000 정도의 높은 품질계수를 나타낸다고 보고되어 있다. 따라서 본 연궁서는 TiO2 박막의 마이크로파 유전특성을 연구하였고 anatase 박막의 유전특성도 측정하였다. TiO2 박막을 RF magnetron reactive sputtering 방법으로 Ar (15 sccm)과 O2 (1.5 sccm) 기체를 사용하여 상온에서 증착하였다. 4mTorr의 증착압력에서 안정한 rutile 박막을 얻었고, 15 mTorrdo서 준안정한 anatase 박막을 얻을 수 있었다. 그리고 그 중간의 압력에서 두 상이 혼합된 박막이 증착되었다. 위와 같은 방법으로 형성한 TiO2 박막의 마이크로파 유전특성을 측정하기 위해 마이크로스트립 링공진기 (microstrip ring resonator)를 제작하였다. 마이크로스트립 링 공진기는 링의 원주길이가 전자기파 파장길이의 정수배가 되면 공진이 일어나는 구조이다. Fused quartz를 기판으로 하여 증착압력을 변수로 하여 TiO2 박막을 증착하였다. 그리고 그 위에 은 (silver)을 사용하여 링 패턴을 형성하였다. 이와 같이 공진기를 제작하여 network analyzer (HP 8510C)로 마이크로파 대역에서의 공진특서을 측정하였다. 공진특성으로부터 전체 품질계수와 유효유전율, 그리고 TiO2 박막의 품질계수를 얻어내었다. 측정결과 rutile에서 anatase로 박막의 상이 변할수록 유전율은 감소하고 유전손실은 증가하는 결과를 나타내었다.

• Journal of the Korean Ceramic Society
• /
• v.56 no.4
• /
• pp.399-402
• /
• 2019

The phase evolution, microstructure, and microwave dielectric properties of (Ba_1-xNa_x)(Mg_0.5-2xY_2xW_0.5-xTa_x)O₃ (0 ≤ x ≤ 0.05) ceramics were investigated. All compositions exhibited a 1:1 ordered perovskite structure. As the value of x increased, the dielectric constant (ε_r) exhibited a tendency to increase slightly. The quality factor reached the maximum value at x = 0.01. The temperature coefficient of resonant frequency (τ_f) increased from -19.32 ppm/℃ to -5.64 ppm/℃ in the positive direction as x increased. The dielectric constant (ε_r), quality factor (Q × f₀), and temperature coefficient of resonant frequency (τ_f) of the composition x = 0.05, i.e., (Ba_0.95Na_0.05)(Mg_0.4Y_0.1W_0.45Ta_0.05)O₃ were 19.9, 128,553 GHz, and -5.6 ppm/℃, respectively.