• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.10
• /
• pp.1338-1343
• /
• 2018

MIMO(Multiple Input Multiple Output) slot antenna that operates on the dual WiFi band(2.401~2.495GHz, 5.18~5.825GHz), in this paper, was studied. The basic theory for the slot design is based on the coupling between adjacent slot, and slots are fed by the each microstrip lines. Two slot antennas for the MIMO operation are located on the left and the right side of top of the metal notebook, and grounds between a notebook and two microstrip feeding lines are connected. Measurement of return loss showed under -6dB on entire design band, and isolation was below than -30dB. Radiation efficiency, average gain and peak gain for the left and the right slot were measured in the anechoic chamber, and showed good performances as 57.25%, -2.42dBi, 5.64dBi and 55.35%, -2.61dBi, 6.42dBi for the 2.4GHz band and 55.89%, -2.58dBi, 7.3dBi and 53.79%, -2.8dBi, 7.54dBi for the 5GHz band.

• Journal of Advanced Navigation Technology
• /
• v.16 no.1
• /
• pp.27-34
• /
• 2012

In this paper, Coplanar waveguide(CPW)-fed slot loop antenna, which is applicable to the dual band(2.4GHz~2.4835GHz, 5.15GHz~5.825GHz) for the wireless LAN, is proposed. In order to miniaturize the proposed antenna, slot loop is bent by meandering. The resonant frequencies in the required dual band are adjusted by variation of the resonant length of slot loop as well as slot width. In particular, use of capacitive coupling CPW feed provides impedance matching without a seperate matching circuit, because the amount of electromagnetic coupling can be controlled by the offset between feed and radiator. As a result, it has been observed that the proposed antenna satisfies not only the required return loss(${\leq}10dB$) but also has high efficiency(${\geq}80%$) over the whole frequency band. In order to check the validity of the proposed antenna, some simulated results for return loss and radiation pattern are presented in comparison with the measured results.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.3
• /
• pp.533-538
• /
• 2018

For WLAN dual-band operation, a modified Yagi dipole antenna is presented. The modified dipole antenna consists of a dipole antenna with open sleeves and parasitic elements. The parasitic elements are used for the practical application of the radiation patterns and high-gain operation at the WLAN dual band. The experimental results showed that the achieved impedance bandwidths were 320 MHz (2.4 to 2.72 GHz) and 640 MHz (5.04 to 5.68 GHz), respectively. The measured maximum gain at the two WLAN bands was 7.74 dBi and 6.93 dBi, respectively.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.7
• /
• pp.987-994
• /
• 2013

In this paper, a dual-band open-ended circular ring moNopole antenna for WLAN(Wireless Local Area Networks) applications. The proposed antenna is based on a planar moNopole design, and composed of open-ended one circular ring of radiating patches for dual-band operation. To obtain the optimized parameters, we used the simulator, Ansoft's High Frequency Structure Simulator(HFSS) and found the parameters that effect antenna characteristics. Using the obtained parameters, the proposed antenna is fabricated. The fabricated antenna is measured at the operating frequencies(2.4-2.484 GHz, 5.15-5.825 GHz), and the return loss coefficient, gain, and radiation patterns are determined.

• International Journal of Internet, Broadcasting and Communication
• /
• v.12 no.1
• /
• pp.37-44
• /
• 2020

In this paper, we proposed a compact printed monopole antenna with an inverted L-shaped slot for dual-band operations. Two operating frequency bands are achieved with the use of an inverted L-shaped slot etched on the radiating strip for bandwidth enhancement and a defected ground structure for return loss improvement in the higher frequency band. The measured results showthat the proposed antenna has impedance bandwidths (S₁₁< -10 dB) of 270 MHz (1.81-2.08 GHz) and 340 MHz (2.36-2.70 GHz), covering the required bandwidths for PCS (1850.5-1989.5 MHz), CDMA 2000 (1850-1990 MHz), TD-SCDMA (1880-2025 MHz) and 2.4 GHz WLAN (2400-2484 MHz). The measured return loss of the proposed antenna has a good value of approximately 27.2 dB at 2.4 GHz WLAN. The antenna's peak gains also have a high value of 1.92 dBi at 2 GHz and 2.12 dBi at 2.45 GHz. The proposed antenna shows omnidirectional radiation patterns over the entire frequency range of interest.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.2
• /
• pp.341-348
• /
• 2018

A WLAN dual band dipole antenna with parasitic elements and a reflector is presented for high gain operation. The parasitic elements are used for practical application and high gain operation of the radiation pattern at the WLAN dual band. The proposed antenna consists of three layers, and has dimensions of $74mm{\times}40 mm{\times}31.4mm$. From the experimental results, the achieved impedance bandwidths were 1035 MHz (2.031-3.066 GHz) and 1119 MHz (5.008-6.127 GHz), respectively. The measured maximum gain at each WLAN band was 6.69 dBi and 7.81 dBi, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.4A
• /
• pp.324-329
• /
• 2009

In this paper, a novel Snowflake-shaped microstrip patch antenna for application in the WLAN(5.2/5.8GHz) band is designed and fabricated. The size of antenna is $21.2{\times}16mm^2$ and substrate is used Taconic-RF30. To obtain sufficient bandwidth in Return loss <-10dB and dual resonance characteristic, the Short-pin is inserted on the patch and the coaxial probe source is used. The measured results of fabricated antenna show 220MHz and 135MHz bandwidth in Return loss <-10dB referenced to the WLAN(5.2/5.8GHz) band. The measured antenna gain is $4.7{\sim}6.9dBi$ in the WLAN(5.2/5.8GHz) band. The experimental 3-dB beam width in I-plane and H-plane are $73.2^{\circ}/82.75^{\circ}$ for 5.1500Hz, $74.56^{\circ}/83.63^{\circ}$ for 5.3500Hz, and $86.24^{\circ}/85.15^{\circ}$ for 5.7850Hz, respectively.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.61-62
• /
• 2015

In this paper, a design method for a dual-band compact slot antenna using SRR(split-ring resonator) conductor is studied. The SRR conductor is loaded inside of a rectangular slot of the proposed antenna for dual-band operation. Final design parameters are obtained by analyzing the effects of the gap between the SRR conductor and slot, and the width of the SRR conductor on the input reflection coefficient and gain characteristics. A prototype of the proposed dual-band slot antenna operating at 2.45 GHz WLAN band and 3.40-5.35 GHz band is designed on an FR4 substrate with a dimension of 30 mm by 30 mm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.3 s.118
• /
• pp.257-264
• /
• 2007

In this paper, we have designed and fabricated a wide-band and high gain antenna which can integrate a standard of IEEE 802.1la$(5.15\sim5.25\;GHz,\;5.25\sim5.35\;GHz,\;5.725\sim5.825\;GHz)$. We inserted a parallel dual slot into a rectangular patch to have wide-band, and we offset an element of capacitance from the slot by using coaxial probe feeding method. We also designed a converter of $\lambda_g/4$ impedance with taper type line so that wide-band impedance can be matched easily. We finally designed structure with $2\times2$ array in order to improve the antenna gain, and the final fabricated antenna could have a good return loss(Return loss$\leq$-10 dB) and a high gain(over 13 dBi) at the range of $5.01\sim5.95\;GHz(B/W\doteqdot940\;MHz)$.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.1
• /
• pp.168-175
• /
• 2013

This paper presents compact dual-band WLAN filter and filter module. They were developed by embedding all of the passive lumped elements into a LTCC substrate. In order to reduce the size/volume of the filter and avoid EM parasitic couplings between the passive elements, the proposed filter was designed using a 3rd order Chebyshev circuit topology and J-inverter transformation technology. The 3rd order Chebyshev bandpass filter was firstly designed for the band-selection of the 802.11b and was then transformed using finite transmission zeros technologies. Finally, the dual-band filter was realized by adding two notch resonators to the 802.11b filter circuit for the band-selection of the 802.11a/g. The maximum insertion losses in the lower and higher passbands were better than 2.0 and 1.3 dB with minimum return losses of 15 and 14 dB, respectively. Furthermore, the filter was integrated with a diplexer to clearly split the signals between 2 and 5 GHz. The maximum insertion and minimum return losses of the fabricated module were 2.2 and 14 dB at 2.4 - 2.5 GHz, and 1.6 and 19 dB at 5.15 - 5.85 GHz, respectively. The overall volume of the fabricated filter was $2.7{\times}2.3{\times}0.59mm^3$.