• Journal of Wetlands Research
• /
• v.17 no.1
• /
• pp.101-111
• /
• 2015

This study conducted a field experiment to estimate the characteristics of the rain garden installed at the site near Haman, also proposed a one-dimensional model to simulate the infiltration and runoff from the rain garden. This model was used to evaluate the rain garden using the rainfall data after the installation and during the last 10 years. Also, this model was applied to the annual maximum rainfall events to quantify the size of the impervious area that the rain garden can offset the adverse effect. The results are summarized below. (1) Hydraulic conductivity of the rain garden was estimated to be about 0.0188 m/hr by the variable-stage experiment. Also, the simulation experiment using the last 10 years rainfall data over the entire roof area showed that the infiltration amount is about 90.38% out of the total rainfall. (2) Infiltration simulation of the annual maximum rainfall events during last 10 years showed that the rain garden can offset the impervious area with its size about 30 times of the rain garden surface.

• Korean Chemical Engineering Research
• /
• v.49 no.5
• /
• pp.644-651
• /
• 2011

Storing hydrogen in solid state hydride is one of the best promising methods for the future hydrogen economy. The total performance of such systems depends on the rate at which the amount of mass and heat migration is supplied to solid hydride. Therefore, an accurate modeling of the heat and mass transfer is of prime importance in optimizing the design of such systems. In this work, Hydrogen storage in Pt-CNTs hydrogen reactor has been intensively investigated by solving 2 dimensional mathematical models. Using a CFD computer software, systematic studies have been performed to elucidate the effect of heat and mass transfer during hydrogen charging periods. It was revealed that the optimized design of hydrogen storage vessel can prevent the increase of system temperature and the charging time due to the convective cooling effects inside the vessels at even high charging pressure. Because none has reported the critical issues of heat and mass transfer for CNT based hydrogen storage system, this work can support the first insight of the optimal design for solid state hydrogen storage system based on CNT in the near future.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.9
• /
• pp.1754-1766
• /
• 2015

Packet classification carried out in Internet routers is one of the challenging tasks, because it has to be performed at wire-speed using five header fields at the same time. In this paper, we propose a leaf-pushed AQT bitmap trie. The proposed architecture applies the leaf-pushing to an area-based quad-trie (AQT) to reduce unnecessary off-chip memory accesses. The proposed architecture also applies a bitmap trie, which is a kind of multi-bit tries, to improve search performance and scalability. For performance evaluation, simulations are conducted by using rule sets ACL, FW, and IPC, with the sizes of 1k, 5k, and 10k. Simulation results show that the number of off-chip memory accesses is less than one regardless of set types or set sizes. Additionally, since the proposed architecture applies a bitmap trie, the required number of on-chip memory accesses is the 50% of the leaf-pushed AQT trie. In addition, our proposed architecture shows good scalability in the required on-chip memory size, where the scalability is identified by the stable change in the required memory sizes, as the size of rule sets increases.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.33 no.2
• /
• pp.49-57
• /
• 2015

The purpose of this study is to provide the visual landscape modelling on Josun royal tombs and surrounding. The visual landscape of traditional heritage is illustrated by the main view points of analysis. This analysis examines limited view points and cannot reflect a reality of environments. Nowadays various equipments and methodologies are developed for the visual landscape research. This study used new tools for analysis which are Sketch up (3D simulation) and mini helicopter (UAV). With those tools, this research examines not only view points of the analysis but also axis views and disincentive environments as a complex analysis. First of all, the research examined 3D modelling for the virtual simulation and drew coordinates and routes for the UAV operating. Secondly, UAV followed this routes and took linear and continuous views that are real scenes. As a result, it drew 3D simulation could illustrate and control the changing of environments such as the forest density and seasonal variations. Thus, comparing both of them shows efficiently landscape analysis. Thirdly, the study compared virtual and real landscape. Using this 3D modelling, this paper able to elaborate heritage environment and surrounding which omitted by view point analysis. Although this study has limitation practice and exercise on the field, the results and suggestions contribute to the various historic heritage managements and conservations. Moreover, it helps to explain the complex and dimensional landscape analysis.

• Korean Journal of Applied Biomechanics
• /
• v.17 no.2
• /
• pp.217-226
• /
• 2007

Putting score counts about 43 % of the golf score. The dominant idea of the putting motion to amateur golfers as well as to many professional golfers is a pendulum-like motion. If a golfer's putting stroke motion is a pendulum-like motion, the putting motion should be straight-back-and-through, the same backswing, downswing, and follow through length and period, and a swing with a fixed hinge joint. If the putting motions of the human are different from the pendulum motion, there could be confusion in understanding and teaching golf putting. The purpose of this study was to examine the center of rotation(COR) of the putter head to reveal whether professional golfers really putt like a pendulum. Thirteen male professional golfers were recruited for the study. Each golfers executed 10.94 m putts six times on an artificial grass mat. Putter head position data were collected through a 60 Hz three-dimensional motion analysis system and low pass filtered with cut-off frequency of 6 Hz. COR of the putter head was mathematically acquired. Each golfer's last five putting motions were considered. The results show that the COR of the putter head was neither fixed nor located inside of the golfer. The medio-lateral directional component of the COR of the putter head fluctuated in the range of 10 cm during downswing and follow through. The anterior-posterior directional component of the COR of the putter head was fixed from the beginning of the downswing through impact. Just after impact, however, it moved to the target up to 60 cm. The superior-inferior directional component of COR of the putter head moved in a superior direction with the beginning of the downswing and showed peak height just prior to impact. During the follow through, it moved back in an inferior direction. The height-normalized peak value of the COR of the putter head was $1.4{\pm}0.3$ height. Technically speaking, male professional golfers' 10.94 m putting motion is not a pendulum-like motion. The dominating idea of a pendulum-like motion in putting might come from the image of the flawless, smooth motion of a pendulum.

• Korean Journal of Applied Biomechanics
• /
• v.17 no.2
• /
• pp.177-185
• /
• 2007

Even though there were no clear definitions of the short game and short game distance, short game capability is crucial for a good golf score. Generally, chip shot and pitch shot are regarded as two principal components of the short game. Chip shot is a short, low trajectory shot played to the green or from trouble back into play. Pitch shot is a high trajectory shot of short length. Biomechanical studies were conducted usually to analyze full swing and putting motions. The purpose of the study was to reveal the kinematical differences between professional golfers' 30 yard $53^{\circ}wedge$ chip shot and $56^{\circ}wedge$ pitch shot motions. Fifteen male professional golfers were recruited for the study. Kinematical data were collected by the 60 Hz three-dimensional motion analysis system. Statistical comparisons were made by paired t-test, ANOVA, and Duncan of the SPSS 12.0K with the $\alpha$ value of .05. Results show that both the left hand and the ball were placed left of the center of the left and right foot at address. The left hand position of the chip shot was significantly left side of that of the pitch shot. But the ball position of the pitch shot was significantly right side of that of the chip shot. All body segments aligned to the left of the target line, open, at address. Except shoulder, there were no significant pelvis, knee, and feet alignment differences between chip shot and pitch shot. These differences at address seem for the ball height control. Pitch shot swing motions(the shoulder and pelvis rotation and the club head travel distance) were significantly bigger than those of the chip shot. Club head velocity of the pitch shot was significantly faster than that of the chip shot at the moment of impact. This was for the same shot length control with different lofted clubs. Swing motion differences seem mainly caused by the same shot length control with different ball height control.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.5 s.96
• /
• pp.501-510
• /
• 2005

In this paper, the miniaturized linear and circular polarization microstrip antennas are designed and fabricated at the resonant frequency of 1.575 GHz. To miniaturize the microstrip patch antenna(MPA), the 'L' type plates are attached under the rectangular microstrip patch. In case of the linear polarization, the size of the microstrip antenna attached the 14 plates is reduced to $67.9\%(47mm{\times}47mm)$ compared with general $MPA(83mm{\times}83mm)$. The return loss and -10 dB bandwidth are -34.4 dB and 49 $MHz(3.1\%)$. And the radiation pattern is broad through the size reduction of the patch. Also in case of the circular polarization, the size of the microstrip antenna with 13 plates is reduced to $54.6\%(53mm{\times}54mm)$ compared with the general $MPA(76mm{\times}83mm)$. The axial ratio is 1.37dB at 1.575 GHz, the 2 dB axial ratio bandwidth is 14 $MHz(0.8\%)$. As that result, we could confirm that 3-dimensional structure with attached 'L' shaped plate is proper form for the miniaturization of linear and circular polarization microstrip antenna.

• Archives of design research
• /
• v.18 no.4 s.62
• /
• pp.247-256
• /
• 2005

This study investigated the status of kitchen of units in elderly housing facilities and the housing needs of residents. Compared with a lot of comprehensive and alternative studies on elderly housing facilities until now, specialized studies of behavior of elderly housing life and detailed dimensional study have hardly made. Therefore we intend to examine the status of kitchen planning on representative elderly housing facilities in Korea. As the methods of this study, we executed a field study into 4 representative elderly housing facilities in Korea. We visited each 2 units out of the outstanding 4facilities and surveyed the total 8 kitchens. Then we analyzed the space planning and kitchen furniture design of them and the state of kitchen commodities, and measured the kitchen equipment. In addition, we executed interview about satisfaction, preference, use from the residents. As a result, we could find out that depending on whether residents were sewed with meal offered from the facilities or not, the pattern of usage and commodities were quite different. It is necessary to supply the simplest spaces just for preparing some refreshment and tea are suitable. And for the self-cooking residents, much larger cabinets and utility rooms are additionally needed. Safety and functional aspect were quite well designed. Washing machines are usually built-in the kitchen cabinets, and residents are satisfied with this arrangement. We hope that the supplementary study about old people habit and behavior will be a good data of kitchen planning for Korean-type elderly housing units of facilities.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.9
• /
• pp.25-37
• /
• 2007

The existing route re-establishment methods which intend to extend the lifetime of the network attempt to find new routes in order not to overly consume energy of certain nodes. These methods outperform other routing algorithms in the network lifetime extension aspect because they try to consume energy evenly for the entire network. However, these algorithms involve heavy signaling overheads because they find new routes based on the flooding method and route re-acquisition occurs often. Because of the overhead they often can not achieve the level of performance they intend to. In this paper, we propose a new route re-acquisition algorithm ARROW which takes into account the cost involved in the packet transmission and the route re-acquisition. Since the proposed algorithm considers future route re-acquisition costs when it first finds the route, it spends less energy to transmit given amount of data while evenly consuming the energy as much as possible. Using 2-dimensional Markov Chain model, we compare the performance of the proposed algorithm and that of other algorithms. Analysis results show that the proposed algorithm outperforms the existing route re-acquisition methods in the signaling overhead and network lifetime aspects.

• Composites Research
• /
• v.13 no.1
• /
• pp.1-10
• /
• 2000

During the compression molding process of the continuous fiber-reinforced polymeric composites, two main problems such as fiber-matrix separation and fiber orientation are produced by the difference of flow velocity. Molded parts are lead to be nonhomogeneous and anisotropic. As the mechanical property of the products are dependent on the separation and orientation, it is important to research the fiber mat structure and molding condition. If the fiber mat structure is changed by the increment of needling, the separation decreases and after compression molding the orientation is easily aligned. As it were, the compression moldability is good. But the defects as tears, thin thickness are produced in the products. Therefore, it is important to clarify the moldability in relation to the usage of products and the expenses of produce on the actual process. Therefore we must make the measurement methods that can define the moldability of products. In this research, the effects of the fiber mat structure(NP = 0, 5, 10, 25, 50 punches/$cm^2$) and the mold geometry($r_p$ = 1, 25, 50 mm) on the moldability of products were discussed. We investigated the case of one-dimensional flow in order to obtain the degree of nonhomogeneity and the fiber orientation function. In result, we could gain the correlation coefficient of the continuous fiber-reinforced polymeric composites. Also we experimented on the cup-type compression molding which was appeared the wrinkle on the flange part by the complex stress condition in order to gain the degree of nonhomogeneity and area ratio. In result, the moldability of products was expressed as the correlation coefficient and area ratio.