• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.1
• /
• pp.76-84
• /
• 2012

In this paper, two kinds of E-plane microstrip-to-waveguide transitions are optimally designed and fabricated for combining output power from multiple small-power amplifiers in a WR-28 waveguide because conventional K connectors cause unnecessary insertion loss and adaptor loss. The transition design is based on target specifications such as a center frequency of 35 GHz, bandwidth of ${\pm}500MHz$, 0.1 dB insertion loss and 20 dB return loss. Performance variation caused by mechanical tolerance and assembly deviation is fully evaluated by three dimensional electromagnetic simulation. The fabricated back-to-back transitions with 16 mm and 26.57 mm interstage microstrip lines show insertion loss per transition of ~0.1 dB at 35 GHz and average 0.2 dB over full Ka band. Also the back-to-back transition shows return loss greater than 15 dB, which implies that the transition itself has return loss better than 20 dB.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2003.11a
• /
• pp.177-184
• /
• 2003

Numerical simulation on marine wind and sea surface elevation was carried out using both three-dimensional hydrostatic and non-hydrostatic models and a simple oceanic model from 0900 LST, August 13 to 0900 LST, August 15, 1995. As daytime easterly meso-scale sea-breeze from the eastern sea penetrates Kangnung city in the center part as basin and goes up along the slope of Mt. Taegullyang in the west, it confronts synoptic-scale westerly wind blowing over the top of the mountain at the mid of the eastern slope and then the resultant wind produces an upper level westerly return flow toward the East Sea. In a narrow band of weak surface wind within 10km of the coastal sea, wind stress is generally small, less than l${\times}$10E-2 Pa and it reaches 2 ${\times}$ 10E-2 Pa to the 35 km. Positive wind stress curl of 15 $\times$ 10E-5Pa $m^{-1}$ still exists in the same band and corresponds to the ascent of 70 em from the sea level. This is due to the generation of northerly wind driven current with a speed of 11 m $S^{-1}$ along the coast under the influence of south-easterly wind and makes an intrusion of warm waters from the southern sea into the northern coast, such as the East Korea Warm Current. On the other hand, even if nighttime downslope windstorm of 14m/s associated with both mountain wind and land-breeze produces the development of internal gravity waves with a hydraulic jump motion of air near the coastal inland surface, the surface wind in the coastal sea is relatively moderate south-westerly wind, resulting in moderate wind stress. Negative wind stress curl in the coast causes the subsidence of the sea surface of 15 em along the coast and south-westerly coastal surface wind drives alongshore south-easterly wind driven current, opposite to the daytime one. Then, it causes the intrusion of cold waters like the North Korea Cold Current in the northern coastal sea into the narrow band of the southern coastal sea. However, the band of positive wind stress curl at the distance of 30km away from the coast toward further offshore area can also cause the uprising of sea waters and the intrusion of warm waters from the southern sea toward the northern sea (northerly wind driven current), resulting in a counter-clockwise wind driven current. These clockwise and counter-clockwise currents much induce the formation of low clouds containing fog and drizzle in the coastal region.

• The Journal of Korean Academy of Prosthodontics
• /
• v.28 no.1
• /
• pp.63-94
• /
• 1990

The purpose of this study was to analyze the displacement and the magnitude and the mode of distribution of the stresses in the lower overdenture, the mucous membrane, the abutment tooth and the mandibular supporting bone when various denture base materials, such as acrylic resin and 0.5mm metal base, and various denture base designs were subjected to different loading schemes. For this study, the two-dimensional finite element method was used. Mandibular arch models, with only canine remaining, were fabricated. In the first denture base design, a space, approximately 1mm thick, was prepared between the denture and the dome abutment. In the second denture base design, contact between the denture and the dome abutment was eliminated except the contact of the occlusal third of the abutment. In order to represent the same physiological condition as the fixed areas of the mandible under loading schemes, the eight nodes which lie at the mandibular angle region, the coronoid process and the mandibular condyle were assumed to be fixed. Each model was loaded with a magnitude of 10 kgs on the first molar region(P1) and 7 kgs on the central incisal region (P2) in a vertical direction. Then the force of 10 kgs was applied distributively from the first premolar to the second molar of each model in a vertical direction(P3). The results were as follows. : 1. When the testing vertical loads were given to the selected points of the overdenture, the overdenture showed the rotatory phenomenon, as well as sinking and the displacements of alveolar ridge, abutment and lower border of mandible under the metal base overdenture were less than those under the acrylic resin overdenture. 2. The maximum principal stresses(the maximum tensile stresses) being considered, high tensile stresses occured at the buccal shelf area, the posterior region of the ridge crest and the anterior border region of the mandibular ramus. 3. The minimum principal stresses(the maximum compressive stresses) being considered, high compressive stresses occured at the inferior and posterior border region of the mandible, the mandibular angle and the posterior border region of the mandibular ramus. 4. The vertical load on the central incisal region(P2) produced higher equivalent stress in the mandible than that on any other region(P1, P3) because of the long lever arm distance from the fixed points to the loading point. 5. Higher equivalent stresses were distributed throughout the metal base overdenture than the resin base overdenture under the same loading condition. 6. The case of occlusal third contact of the abutment to the denture produced higher equivalent stresses in the abutment, the mandibular area around the abutment and the overdenture than the case of a 1mm space between the denture and the abutment. 7. Without regard to overdenture base materials and designs, the amounts and distribution patterns of equivalent stresses under the same loading condition were similar in the mucous membrane.

• Ocean and Polar Research
• /
• v.29 no.2
• /
• pp.87-99
• /
• 2007

This study was conducted to understand the source and behavior of organic matter using the fluorescent technique (excitation-emission matrix) as a part of environmental monitoring program in the Korea manganese nodule mining site in the Northeastern Pacific Ocean. Water samples were collected at $0^{\circ},\;6^{\circ}N$, and $10.5^{\circ}N$ along $131.5^{\circ}W$ in August 2005. The concentration of total organic carbon (TOC) ranged from 58.01 to $171.93\;{\mu}M-C$. The vertical distribution of TOC was characterized as higher in the surface layer and decreased with depth. At $6^{\circ}N$, depth-integrated (from surface to 200 m depth) TOC was $337.1\;gC/m^2$, which was 1.4 times higher value than other stations. The exponential decay curve fit of vertical profile of TOC indicated that 59% of organic carbon produced by primary production in the surface layer could be decomposed by bacteria in the water column. Dissolved organic matter is generally classified into two distinctive groups based on their fluorescence characteristics using three-dimensional excitation/emission (Ex/Em) fluorescence mapping technique. One is known as biomacromolecule (BM; protein-like substance; showing max. at Ex 280/Em 330), mainly originated from biological metabolism. The other is geomacromolecule (GM; humic-like substance; showing max. at Ex 330/Em 430), mainly originated from microbial degradation processes. The concentration of BM and GM was from 0.42 to 7.29 TU (tryptophan unit) and from 0.06 to 1.81 QSU (quinine sulfate unit), respectively. The vertical distribution of BM was similar to that of TOC as high in the surface and decreased with depth. However, the vertical distribution of GM showed the reverse pattern of that of BM. From these results, it appeared that BM occupied a major part of TOC and was rapidly consumed by bacteria in the surface layer. GM was mainly transformed from BM by microbial processes and was a dominant component of TOC in the deep-sea layer.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.541-546
• /
• 2020

The surveillance radar for naval ships is an essential equipment of a battle system that executes the detection and tracking of targets, and the shooting support function; it calculates the three-dimensional track of the target range, azimuth, and altitude to carry out its duty. The surveillance radar consists of an antenna, a transceiver, a processing unit, and an air dryer section. The radar radiates the transmission signal on the antenna section, receives the reflected signal from the target, and amplifies the signals on the transceiver section. The signal received from the antenna is used to provide the operator with target information in various ways. This study identified the display problems when the information about the target is displayed through the radar. The causes of the problems were analyzed and improved. The tracking disappearance phenomenon caused by the altered-course of the ship was improved on the TWS tracking algorithm. The validity of the improved TWS tracking algorithm was confirmed by the normal condition of the target status on the B-scope.

• Journal of Acupuncture Research
• /
• v.33 no.3
• /
• pp.45-66
• /
• 2016

Objectives : The purpose of this study is to find parameters to compare the effects of Sa-Am acupuncture with gall bladder jeonggyeok and seunggyeok on radial pulse in healthy subjects. Methods : 60 healthy subjects participated in this study and divided into the gall bladder jeonggyeok group (GB+ group), the gall bladder seunggyeok group (GB- group) and the control group. Radial pulse was measured by a 3 dimensional pulse imaging system (DMP-3000) before, immediately after, 30 minutes after and 60 minutes after acupuncture on the Cun, Guan and Chi in the GB+, GB- group and at the same time for the control group. Results : 1. The GB+ and GB- group exhibited significantly increased T, M4/M1 and decreased T1/T, T2/T, T5/T, M1, M2 compared to the control group. 2. The GB+ and GB- group exhibited significantly increased H4, Ad/Ap, RAI/HR and decreased As/Ap, Aw/Ap in the right Guan and decreased pulse power volume/min in the left Guan compared to the control group. 3. The GB- group exhibited significantly decreased M3, M3/M1 and increased M4/M1, M5, M5/M1 compared to the GB+ group. The GB+ group exhibited significantly decreased T4/(T-T4) compared to the GB- group. 4. The GB- group exhibited significantly decreased H1 in the right Guan, Chi, H4, pulse area in the right Chi, H5, pulse power volume/min in the left Chi, right Chi, and increased main peak angle in the right Guan, Chi compared to the GB+ group. Conclusion : The effect of gall bladder jeonggyeok and seunggyeok in healthy humans may be observed on various parameters. The parameters analyzed in this study may be used to differentiate effects between gall bladder jeonggyeok and seunggyeok on radial pulse. Further studies on the effects of Sa-Am acupuncture using radial pulse are needed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.2
• /
• pp.610-619
• /
• 2016

Digital manufacturing (DM) technology helps engineers design products promptly and reliably at low production cost by simulating a manufacturing process and the material behavior of a product in use, based on three-dimensional digital modeling. The computing infrastructure for digital manufacturing, however, is usually expensive and, at present, the number of professional design engineers who can take advantage of this technology to a product design accurately is insufficient, particularly in small and medium manufacturing companies. Considering this, the Korea Institute of Science and Technology Information (KISTI) and H University is operating a DM track in the form of Industry-University-Research Institute collaboration to train high-performance-computing-based DM professionals. In this paper, a series of courses to train students to work directly into DM practice in industry after graduation is reported. The operating cases of the DM track for two years since 2013 are presented by focusing on the progress in establishment, lecture and practice contents, evaluation of students, and course quality improvement. Overall, the track management, curriculum management, learning achievement of students have been successful. By expediting more active participation of the students in the track and providing more internship and job offers in the participating companies in addition to collaborative capstone design projects, the track can be expanded by fostering a nationwide training network.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.23 no.6
• /
• pp.429-441
• /
• 2011

In the southeast coastal zone of Yellow Sea, the tide characteristics showing ebb-dominant tide and tidal flow were confirmed by analysis of observed tide and tidal currents. Physical factors generating asymmetric tide were reviewed. Influence of bottom shear stress, tidal flat, and nonlinear terms in shallow water equations was investigated by two-dimensional tide modeling. The model results gave good agreements with observed tides, but the amplitude of simulated $M_4$ tide was less than that of observed tide. The tidal flats existing in the study area widely have great effect on the generation of nonlinear tide. The M4 tide is mainly generated near the tidal flats. The deletion of tidal flats prevents the production of the M4 tide. We can conclude that the wide tidal flats is a primary cause of tide asymmetry in the study area.

• Clinical and Experimental Pediatrics
• /
• v.60 no.11
• /
• pp.373-378
• /
• 2017

Purpose: The aim of this study was to investigate the statistical properties of four previously developed pediatric coronary artery z score models in healthy Korean children. Methods: The study subjects were 181 healthy Korean children, whose age ranged from 1 month to 15 years. The diameter of each coronary artery was measured using 2-dimensional echocardiography and converted to the z score in the four models (McCrindle, Olivieri, Dallaire, and Japanese model). Descriptive statistical analyses and 1-sample t tests were performed. Results: All calculated z scores had P values of ${\geq}0.050$ using the Kolmogorov-Smirnov test. The one sample t test showed that the mean z scores did not converge to zero except in 1 model, and the mean right coronary artery (RCA) z score was less than zero in all 4 models. The smaller RCA diameter in this study could be associated with the more distal measuring point used to avoid the conal branch. The percentage of subjects with extreme z score values (${\geq}2.0$ and ${\geq}2.5$) for the left main coronary artery (LMCA) seems to be higher in the Dallaire (4.9% and 3.3%) and Japanese models (7.1% and 3.8%). Conclusion: All 4 models showed statistical feasibility of normal distribution. More precise instructions would be needed for the measurement of the RCA. The higher percentage of extreme z scores for the LMCA is compatible with the basic understanding of anatomic variation in the LMCA.

• Archives of Plastic Surgery
• /
• v.35 no.2
• /
• pp.139-146
• /
• 2008

Purpose: The objective of this study is anthropometric analysis of mouth and lower face of Korean. The relationship of soft-tissue to underlying bony structures determine the overall aesthetics of the face. The goal of aesthetic surgery of the face is to achieve the ideal normal and enhance the aging face. The purpose of present study was to determine the change of the morphology of the mouth and lower face based on soft-tissue landmarks according to age group to facilitate prediction during aesthetic surgery. Methods: The standardized photographs of 2,018 healthy volunteers(18 to 79 years of age; 1,070 males, 948 females) were investigated. Age groups were classified into young, middle-aged, and elderly groups. Five and seven items were measured on frontal and lateral view photographs, respectively. Individual dimensions were compared in the three age groups and between males and females. Results: The width of mouth is 4.5 times larger than that of philtrum. Most of measured data decreased with age. However, woman's lip width of the mouth somewhat increased from the young to elderly. The width of lower face is 2.5 times larger than mouth in young age group and increased slightly from the young to middle-aged and thereafter slightly decreased to elderly group. Upper lip was more higher than lower lip and male lip was more higher than female. But male and female lip height is similar at old age. Conclusion: Most of Koreans showed prominent lower face because of the development or protrusion of the mandible. And the descent of soft-tissue around the mouth was one of the significant characteristics of senile change. The posterior retrusion of the subnasal was an another characteristic. This study will help to elucidate the age-related dimensional differences of the human being and to provide useful information for clinical applications in oral and aesthetic surgery.