• The Korean Journal of Rheology
• /
• v.6 no.2
• /
• pp.104-118
• /
• 1994

단섬유 보강 플래스틱 재료의 사출성형 충전공정에서 금형재의 유동장이 섬유 배향 상태를 형성하는데 중요한 역할을 할 뿐만 아니라 섬유의 배향상태가 역으로 유동장에 영향 을 미친다. 충전유동과 섬유 배향의 연계해석을 위하여 단섬유에 의한 추가적인 응력을 포 함하는 Dinh과 Armstrong의 이방성 구성방정식을 충전유동의 해석에 도입하였다. 평명방향 으로의 속도구배에 의한 응력을 고려하여 새롭게 유도된 압력 지배방정식과 에너지방정식을 유한요소법과 유한차분법을 이용하여 풀고 동시에 2차배향텐서의 변화방정식을 4차 Runge-kutta 방법을 이용하여 풀었다. 절점 게이트 주변의 확장유동영역과 라인게이트를 통한 수축유동영역에서 평면방향으로의 속도구배에 의한 응력이 유동장에 미치는 영향을 고 찰하였다. 확장유동영역에서는 평면방향으로의 속도구배에 의한 영향이 추가적인 유량으로 나타나면서 주어진 유량조건하에서 평면방향으로의 속도구배에 의한 응력을 고려하지 않은 경우보다 작은 압력구배를 나타냈다. 수축유동영역에서는 위와 반대의 결과를 보였다. 이러 한 경향은 섬유의 부피분율이증가하거나 모양비가 커짐에 따라 증가한다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.11
• /
• pp.3573-3588
• /
• 1996

The flow through a centrifugal compressor impeller was calculated using the 3-dimensional Navier-Stokes solution method. A control volume method based on a rotating curvilinear coordinate system was used to solve the time-averaged Navier-Stokes equations, and a standard k-.epsilon. model was used to obtain eddy viscosity. Numerical results and experimental data were compared for the overall performance of the impeller, the pressure distributions along the shroud wall and the detailed flowfields at the design and off-design conditions, which showed good coincidence. The flow through the impeller is complex with the curvature of the streamlines and rotation. The development of secondary flows and the jet-wake flow characteristics, which is the main source of flow loss, was discussed. Calculation results show quite different patterns as the flow rate changes.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.1
• /
• pp.1-8
• /
• 2011

An analytical study on the flow resistance of tree-shaped channel-flow architectures was carried out based on the principle of the constructal law; the evolutionary increase in the access to currents that flow through the channels with improvements in the flow configurations were studied in a square domain using two diameters. Two types of tree-shaped configurations were optimized. The minimized global flow resistance decreased steadily as the system size $N^2$ increased. From the two channel configurations, the one that resulted in better pressure drop was selected. Further, it was shown that the system performance can be enhanced by adopting the second tree-shaped configurations when the system size is greater than $18^2$.

• Journal of the Korea Convergence Society
• /
• v.5 no.2
• /
• pp.19-23
• /
• 2014

In this study, the air resistance is studied by using flow analysis near automotive body due to the its shape. Flow velocities of airs entering into inlet plane are two kinds of 70 km/h and 100 km/h. Air resistance in case of high speed driving(100 km/h) becomes higher than regular speed driving(70 km/h) and the resistance in case of the car with wider cross section at front side becomes higher than narrower cross section. By using this analysis result, the shape of automotive body can be effectively designed in order to reduce the air resistance.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.9
• /
• pp.2261-2270
• /
• 1995

Flow patterns were measured in an unshrouded centrifugal impeller. The flow rate in measurements was fixed at the value corresponding to a nearly zero incidence at the blade inlet. By using a single slanted hot-wire probe and a Kiel probe mounted on the impeller hub disk, the 3-D relative velocities and the rotary stagnation pressures were measured in seven circumferential planes from the inlet to the outlet of the impeller rotating at 700rpm, which diameter is 0.39 meter, and the static pressures and the slip factor at the impeller outlet were calculated from the measured values. From the measured data, the primary/secondary flows, the leakage flows, the wake-jet flows, static pressure distribution on blade surfaces and the wake production mechanism in the impeller passage were investigated.

• Nuclear Engineering and Technology
• /
• v.17 no.4
• /
• pp.290-301
• /
• 1985

600MW(e) CANDU Primary Heat Transport System (PHTS) is composed of the two “figure-of-eight” loops and is designed to operate with the 4% Reactor Outlet Header (ROH) quality at its rated power. This existence of the two compressible regions and the positive flow-qualitly-void feedbacks are the sources of the PHTS flow instability. To ensure the PHTS stability, ROH-ROH interconnect pipes are installed as passive systems. This paper describes the investigation of the PHTS flow instability at its design full power condition. Also studied are the interconnect effect and the inherent system damping effect on the system stability. The time domain stability analyses are accessed by using the ATHER/MOD-I code which is the improved version of the KAERI developed ATHER code. Under the most adverse system modelling, the “figure-of-eight” symmetric loop shows divergent flow oscillations. Under with the interconnect, the PHTS stability is remarkably enhanced so that the system becomes stable. However, even under the conservative pressurizer modelling, the PHTS shows the more convergent flow oscillations. With the interconnect and the pressurizer modelling, its stability is highly credited. Conclusively, the inherent system damping by pressurizer itself can credit the PHTS stability without the interconnect.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.2
• /
• pp.109-117
• /
• 2015

Aircraft needs an inlet duct to supply the airflow to engine face. A fighter aircraft that requires low radar observability has to hide the engine face in the fuselage to reduce the Radar Cross Section(RCS). Therefore, the flow path of the inlet duct is changed into S-shape. The performance of the aircraft engine is known to be influenced by the shape and the centerline curvature of the S-Duct. In this study, CFD analysis of the RAE M 2129 S-Duct has been performed to investigate the influence of aspect ratio of inlet geometry. The performance of the S-Duct is evaluated in terms of the distortion coefficient. To simulate the flow under adverse pressure gradient better, $k-{\omega}SST$ turbulence model is employed. The computational results are validated with the ARA experimental data. The secondary flow and the flow separation are observed for all computational cases, while the semi-circular geometry has been found to produce the best results.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.321-325
• /
• 2008

In this paper, heat transfer changes due to the shock/boundary layer interaction were investigated on surfaces where secondary jet are injected. With an infra-red thermography, surface temperature was measured and the measured data was used to obtain the convective heat transfer. Heat transfer is enhanced with increment of momentum ratio. And normal injection case has a higher heat transfer value than that of 15 degrees inclined injection case. Secondary injection momentum ratio and injection angle affect the surface heat transfer distribution.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.496-501
• /
• 2003

Computational study is performed to understand the fluidic thrust vectoring control of an axisymmetric nozzle, in which secondary gas injection is made in the divergent section of the nozzle. The nozzle has a design Mach number of 2.0, and the operation pressure ratio is varied to obtain the different flow features in the nozzle flow. The injection flow rate is varied by means of the injection port pressure. Test conditions are in the range of the nozzle pressure ratio from 3.0 to 8.26 and the injection pressure ratio from 0 to 1.0. The present computational results show that, for a given nozzle pressure ratio, an increase of the injection pressure ratio produces increased thrust vector angle, but decreases the thrust efficiency.

• Journal of Energy Engineering
• /
• v.1 no.1
• /
• pp.76-86
• /
• 1992

A three-dimensional model has been developed for pulverized coal combusters and gasifiers. Coal devolatilization, heterogeneous char oxidation, gas particle interchange, radiation, gas phase oxidation, primary and secondary stream mixing, and heat losses are considered. A finite difference method was used to solve the ordinary non-linear differential equations. The effects of primary and secondary stream flow ratio and coal particle size are investigated.