• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1888-1893
• /
• 2011

Considering the dynamic performance and stability of railroad vehicles has begun to grab the attention because of developing the high speed train recently. A development based on an analysis of dynamics and verification has to be required to study the stability of vehicle performance. Several ways of analysis were using the look-up table to apply the wheel-rail contact characteristics quickly, whereas there is a constraint of the wheelset lateral displacement. In this study, an development of searching the wheel-rail contact position has been provided. The 2-point contact between wheel and rail during the driving condition can be calculated by numerical analysis. Moreover, a reliability is verified by comparing the result with a commercial program.

• KDI북한경제리뷰
• /
• v.21 no.11
• /
• pp.46-56
• /
• 2019

2018년 싱가포르에서 북미 정상회담이라는 역사적인 이벤트가 성사되었다. 2019년 1월 1일, 김정은 북한 국무위원장이 "미국 대통령과 언제든 또다시 마주 앉을 용의가 있다"는 신년사를 발표했고 트럼프 대통령이 이에 화답하며 이후 양측 간 실무 협상이 이뤄졌다. 그 결과 2월 말, 양국 정상은 베트남 하노이 2차 정상회담에서 마주할 수 있었다. 그러나 회담은 별다른 성과 없이 결렬됐다. 6월에는 갑작스러운 남-북-미 DMZ 회동이 이뤄졌으나 북한이 갑작스레 수차례 미사일 도발을 감행하며 북미 관계는 다시 교착 상태에 빠지게 됐다. 이후 10월에는 북한 비핵화 협상을 위한 북미 양측의 실무접촉이 스웨덴 스톡홀름에서 진행됐지만 이 또한 뚜렷한 성과를 도출하지 못했다. 양측 모두 현재까지 제3차 북미 정상회담에 대한 가능성은 열어놓은 상태다. 본 경제자료에서는 2019년 북미관계 주요 내용을 정리하고자 한다. 첫 번째 장에서는 하노이 제2차 북미정상회담의 과정과 내용을 정리한다. 두 번째 장에서는 하노이 회담 이후 북미 관계를 살펴보고 남북미 정상 판문점 회동의 과정을 정리해 본다. 세 번째 장에서는 스톡홀름 북미 실무협상 전 북한의 미사일 발사와 함께 실무협상 전개의 주요사항을 정리한다. 본 자료는 다양한 언론 보도를 근거로 재구성하여 제공한다

• Journal of Adhesion and Interface
• /
• v.11 no.4
• /
• pp.149-154
• /
• 2010

Interfacial evaluation was investigated for single-carbon fiber/phenolic and carbon nanotube (CNT)-phenolic composites by micromechanical technique and electrical resistance measurement combined with wettability test. Compressive strength of pure phenol and CNT-phenolic composites were compared using Broutman specimen. The contact resistance of CNT-phenolic composites was obtained using a gradient specimen by two and four-point methods. Surface energies and wettability by dynamic contact angle measurement were measured using Wilhelmy plate technique. Since hydrophobic domains are formed as heterogeneous microstructure of CNT in the surface, the dynamic contact angle exhibited more than $90^{\circ}$. CNT-phenolic composites exhibited a higher apparent modulus than neat phenolic case due to better stress transferring effect. Work of adhesion, $W_a$ between single-carbon fiber and CNT-phenolic composites exhibited higher than neat phenolic resin due to the enhanced viscosity by CNT addition. It was consistent with micro-failure patterns in microdroplet test.

• Journal of Oral Medicine and Pain
• /
• v.32 no.4
• /
• pp.365-373
• /
• 2007

Destruction of oral soft and hard tissues and resulting problems seriously affect the life quality of xerostomic patients. Although artificial saliva is the only regimen for xerostomic patients with totally abolished salivary glands, currently available artificial salivas give restricted satisfaction to patients. The purpose of this study was to contribute to the development of ideal artificial saliva through comparing viscosity and wettability between CMC solutions and human saliva. Commercially-available CMC is dissolved in simulated salivary buffer (SSB) and distilled deionized water (DDW). Various properties of human whole saliva, human glandular saliva, and a CMC-based saliva substitutes known as Salivart and Moi-Stir were compared with those of CMC solutions. Viscosity was measured with a cone-and-plate digital viscometer at six different shear rates, while wettability on acrylic resin and Co-Cr alloy was determined by the contact angle. The obtained results were as follows: 1. The viscosity of CMC solutions was proportional to CMC concentration, with 0.5% CMC solution displaying similar viscosity to stimulated whole saliva. Where as a decrease in contact angle was found with increasing CMC concentration. 2. The viscosity of human saliva was found to be inversely proportional to shear rate, a non-Newtonian (pseudoplastic) trait of biological fluids. The mean viscosity values at various shear rates increased as follows: stimulated parotid saliva, stimulated whole saliva, unstimulated whole saliva, stimulated submandibular-sublingual saliva. 3. Contact angles of human saliva on the tested solid phases were inversely correlated with viscosity, namely decreasing in the order stimulated parotid saliva, stimulated whole saliva, unstimulated whole saliva, stimulated submandibular-sublingual saliva. 4. Boiled CMC dissolved in SSB (CMC-SSB) had a lower viscosity than CMC-SSB (P < 0.01 at shear rate of $90s^{-1}$). 5. For human saliva, contact angles on acrylic resin were significantly lower than those on Co-Cr alloy (P < 0.01). 6. Comparing CMC solutions with human saliva, the contact angles between acrylic resin and human saliva solutions were significantly lower than those between acrylic resin and CMC solutions, including Salivart and Moi-Stir (P <0.01). The effectiveness of CMC solutions in terms of their rheological properties was objectively confirmed, indicating a vital role for CMC in the development of effective salivary substitutes.

• Pediatric Infection and Vaccine
• /
• v.17 no.2
• /
• pp.137-147
• /
• 2010

Purpose : The purpose of this study is to evaluate the usefulness and limitation of QuantiFERON-TB Gold (QTB) for diagnosis of latent tuberculosis in children. Methods : The medical records of 112 children who were tested by tuberculin skin test (TST) and QTB for detection of latent tuberculosis (TB) in Eulji General Hospital during the period from January 2007 to June 2009 were retrospectively reviewed. Results : Of the 112 participants, the clinical TB group included 15 (13.4%), the contact group included 43 (38.4%), and the non-contact group included 54 (48.2%). Positive rates of TST and QTB were 100% and 80% in the clinical TB group, 64% and 14% in the close contact group, 27% and 0% in the casual contact group, and 52% and 2% in the non-contact group, respectively. Sensitivity of QTB was 80.0% and specificity was 92.6%. Agreement between QTB and TST was poor ($\kappa$=0.209). We also confirmed that the positive rate of QTB increased as the age of the patient increased (P=0.011). A QTB indeterminate result was observed in 11 (9.8%) subjects. QTB was retested in 15 subjects. In 5 of the 6 subjects who had positive results initially, positive results persisted for a median 2.2 months after termination of treatment. Conclusion : Although QTB was associated with several problems, including low sensitivity and a high rate of indeterminate results, it had clinical importance due to its high specificity. We found good correlation with regard to exposure and QTB positivity, including that of young children under 5 years of age. However, clinical application of interferon-$\gamma$ releasing assay for young children for diagnosis of active and latent tuberculosis will require additional prospective studies.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2005.05a
• /
• pp.183-185
• /
• 2005

영산강 유역 생활하수처리장의 방류수의 분석 결과, 일일 처리량이 타지점들에 비해 다량이며 인구수가 많고 산업이 발달되어 있는 광주지역에 위치해 있는 광주 하수처리장과 송대 하수처리장에서 다종의 유기화합물이 검출되었다. 특히 polycyclic compounds, phenols, phthalates, pesticides는 여름철에 다종 고농도로 검출되어 여름철 영산강 유역 방류수의 주 오염물질로 판단된다. 이들 광주 하수처리장 방류수와 송대 하수처리장 방류수에서는 내분비계 장애물질인 diethylph thalate와 bis(2-ethyhexyl)phthalate가 4회 이상 검출되었다. 또한 송대, 장성 하수처리장에서 고농도로 검출된 물질이 대부분 산업용 화학물질이나 반응에 의해 2차로 생성되는 화학물질들이 다종으로 검출되었다. 따라서 이들 지점의 영향은 산업폐수에 의한 것으로 판단된다. 현재 각 하수처리장에서 실시하는 표준활성오니법, 회전원판접촉식 처리공정으로는 본 연구에서 검출된 물질과 같이 생태계나 인간의 건강에 유해한 유기화합물을 처리하기에는 역부족이라고 판단된다. 따라서 영산강 유역 수질 안정성을 확보하기 위해서는 polycycli compounds, phenols, phthalates, pesticides와 같은 난분해성 유기 화합물질을 처리할 수 있는 고도산화처리 시스템 도입이 필요하다.

• The Korean Journal of Rheology
• /
• v.3 no.1
• /
• pp.38-46
• /
• 1991

저분자량(분자량: 1.04$\times$104 g/mole)과 고분자량(3.84$\times$106) 폴리스타이렌 브렌드를 제조하고 무접촉 무마찰을 이용한 비틀림 크립장치를 사용하여 점도, 크립 캄플라이언스들 을 측정하고 또 지연 스펙트라도 계산해 내었다. 고분자량의 농도는 0, 2, 10, 20, 50, 70, 100 중량 퍼센트였다. 점도는 블렌드의 중량평균 분자량이 임계분자량이상이면 중량평균의 3.5승에 비례했다. 중량평균 분자량>임계분자량 인블렌드의 경우 정상상태 회복 캄플라이언 스는 중량평균의 3.5승에 비례했다. 중량평균 분자량>임계분자량 인 블렌드의 경우 정상상 태 회복 캄플라이언스는 중량평균의 -2.3승에 비례했다. 지연스펙트라를 검토한 결과 폴리 스타이렌의 임계분자량은 38000 g/mole 쯤으로 추정되었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.9
• /
• pp.3155-3160
• /
• 2010

Nowadays, most car manufactures have tried to improve fuel efficiency and corrosion resistance of car body. Therefore, use of high strength steels and coated steel becomes more and more increased. In this study, spot weld characteristics according to lap sequence of sheets were analyzed using simulation method for three different steel sheet of car body which were EDDQ class coated steel with 0.7t, high strength steel 440R with 1.2t and advanced high strength steel DP 590 with 1.0t. Using simulation, weldability was evaluated by nugget size of welded zone according to nugget growth curve and welding current with respect to lap sequence of sheets. Contact resistance of each sheets contact point was used to analyze formation of nugget and optimal lap sequence was suggested.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.15 no.5
• /
• pp.19-24
• /
• 1978

In this paper, the functional propertied of vibrotactile sense of skin were studied by means of psycophysical experiments with respect to frequency and waveform of mechanical vibration, two-point threshold, contactor size of stimulators. Furthermore, leased on the experimental result, a small vibrotactile stimulator made of piezoelectrc ireed vibrator array was proposed for a aid blind to recognition of the Korean letters. A tactile output image is presented by an 8 row$\times$1 column array of samall vibrator reeds with 200 Hz rectangular wave, the array fitting on a fore-finger. Under the control of the NOVA mini-computer, the bimorph reeds array could represent any of one of the 24 characters of the Korean vowel and consonant at the 8 positions from left to right on the array. Without learning effect, the identification test of the Korean characters by the designed experimental system was carried out. The average rate of correct response was 90%.

• Journal of Internet Computing and Services
• /
• v.10 no.2
• /
• pp.53-63
• /
• 2009

e-Passport system is new type of emigration and immigration control system and it is a research to introduce the e-Passport Authentication Protocol with Improved Efficiency is lively proceeded over the entire world. The e-Passport's chip has a biometric information and personal identification information, Radio Frequency Identification(RFID) technology is used for communication with the Inspection System(IS). However, the feature of the RFID system may bring about various security threats such as eavesdropping, data forgeries, data alternation, cloning, biometric data-leakage. Therefore, in this paper, we analyse the e-Passport system's authentication protocol to protect vulnerability and proposed e-Passport system's authentication protocol reduce computation. Also, we compared their efficiency.