• Resources Recycling
• /
• v.12 no.4
• /
• pp.20-29
• /
• 2003

In order to efficiently recycle the waste solution resulting from shadow mask processing, nano-sized Ni-ferrite powder was fab-ricated through spray pyrolysis process. The average particle size of the powder was below 100nm. In this study, the effects of the reaction temperature. the concentration of raw material solution and the injection speed of solution on the properties of powder were respectively investigated. As the reaction temperature increased from $800^{\circ}C$ to $1100^{\circ}C$, average particle size of the powder significantly Increased and power structure became more solid, whereat its specific surface area was greatly reduced. Formation rate and crystallization of($NiFe_2$$O_4$) phale increased along with the temperature rise. As the concentrations of iron and nickel components in wastere solution increased, particle size of the powder became larger, particle size distribution became more irregular, and specific surface area was reduced. Formation rate and crystallization of $NiFe_2$$O_4$ phase increased significantly along with the increase of the concentration of solution. As the inlet speed of solution increased, particle size of the powder became larger, particle size distribution became wider, specific surface area was reduced and powder structure became less solid. As the inlet speed of solution decreased, formation rate and crystallization of $NiFe_2$$O_4$ phase significantly increased.

• Korean Journal of Materials Research
• /
• v.7 no.12
• /
• pp.1027-1032
• /
• 1997

본 연구에서는 용사용WC-17%Co 복합분말을 분무건조법으로 제조하고 열처리 온도(85$0^{\circ}C$, 100$0^{\circ}C$, 115$0^{\circ}C$, 130$0^{\circ}C$)에 따른 조립분말의 미세구조, 입도분포, 유동도, 및 결정상변화를 고찰하였다. 분무건조상태의 입형은 구형이었으며, 입도분포, 평균입자크기, 유동성은 각각 20.6-51.7$\mu\textrm{m}$, 27.2$\mu\textrm{m}$, 0.26 sec/g 이었다. 열처리에 의하여 조립분말은 치밀화되어 130$0^{\circ}C$ 열처리 후에는 입도분포와 평균입자크기가 각 각 6.9-37.9$\mu\textrm{m}$과 17.8$\mu\textrm{m}$로 감소하였으며, 유동성은 0.12 sec/g로 향상되었다. 열처리중에 WC와 Co의 상화확산에 의하여 Co$_{6}$W$_{6}$C및 Co$_{3}$W$_{3}$C이 생성되었으며, 두 상이 나타나는 임계온도는 115$0^{\circ}C$이었다.

• Journal of computational fluids engineering
• /
• v.12 no.2
• /
• pp.32-36
• /
• 2007

NUFLEX is a general purpose program for the analysis 3D thermo/fluid flow and pre/post processor in a complex geometry. NUFLEX is composed of various physical models, such as phase change(solidification/melting) and spray, MHD(Magneto Hydraulic Dynamics) models. It is possible to simulate continuous cast iron process and spray droplet breakup/collision phenomenon. For the verification of these models, compared with the experimental data and commercial CFD code's results. The results show good agreements with experimental and comercial CFD codes's results.

• Korean Journal of Food Science and Technology
• /
• v.29 no.6
• /
• pp.1322-1326
• /
• 1997

Characteristics of viscosity and spray dried particles for several polysaccharides were studied to investigate the possibilities as wall materials for microencapsulation. Viscosities of 10% maltodextrin, 10% gum arabic, 10% dextran, 1% gum locust bean, and 1% gum karaya were 2.2 mPa.s, 9.2 mPa.s, 13.0 mPa.s, 4660.0 mPa.s, and 77.0 mPa.s, respectively. In scanning electron micrographs for spray dried polysaccharides, gum arabic had spherical shapes at 20% and 30% emulsion concentration, while trailed shapes at 40%. Maltodextrin had uniform spherical shapes at 30%, while aggregated form with various kinds of capsule sizes at 40%. Dextran had spherical shapes at 20%, while trailed fibrous shapes at over 30%. Mixed polysaccharides with gum arabic:maltodextrin (1:3, w/w) had uniform spherical shapes at 20%, 30%, and 40% with increasing diameter with increasing concentration.

• Resources Recycling
• /
• v.27 no.2
• /
• pp.32-37
• /
• 2018

This study was conducted as a preliminary study for the recycling of palladium and palladium oxide. In this study, thermodynamic equations for the formation of palladium oxide (PdO) are established. Palladium chloride is dissolved into hydrochloric acid to generate a palladium chloride solution. Nanosized palladium oxide powder with an average particle size below 30 nm were generated from this raw material solution by means of a spray pyrolysis process. The palladium oxide particles were composed of a single solid crystal. The results of XRD analysis showed that only a PdO phase of the generated powder was formed. And, the specific surface area of the generated palladium powder was approximately $32m^2/g$.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.17 no.3
• /
• pp.215-219
• /
• 1988

This experiment was carried out to investigate the shelf life of fresh pork by spraying 2%(v/vf) acetic acid solution. Both treated with acetic acid and untreated pork were stored at $4^{\circ}C$. The spray of acetic acid solution was effective on growth inhibiton of aerobic and coliform bacteria. The pH, volatile basic nitrogen contents, and thiobarbituric acid value of fresh pork treated with acetic acid were lower than untreated pork during storage. Meat color was more darkened immediately after acetic acid treatment, but untreated pork was more darkened after 2 days storage.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.11
• /
• pp.999-1004
• /
• 2010

Recently, many technologies have been developed in order to satisfy stringent emission regulations. However, in the case of diesel engines, the stringent emission regulations with respect to NOx and PM have not yet been satisfied. A dramatic reduction in the NOx and PM emissions could be achieved by using after-treatment systems such as lean NOx trap (LNT) and urea-SCR systems. However, the high temperature in the exhaust pipe affects the spray behavior of the secondary injector, which is used for supplying the Urea-SCR. Because of this high temperature, it is difficult to achieve uniform distribution of the reducing agent in the manifold. In this paper, the characteristics of a urea-SCR injector used for injecting in the exhaust pipe are presented. The purpose of this study was to investigate the spray characteristics of the injector, such as the spray angle, injection quantity, and SMD. In addition, laser diagnostics and high-speed-camera images were used to analyze the injector spray characteristics and to present a distribution of reduction in the transparent manifold.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.88-88
• /
• 2017

Zn코팅은 우수한 내식성과 경제성을 바탕으로 자동차나 건축자재 등 산업의 전반적인 분야에서 광범위하게 사용되고 있다. 하지만 최근 한정된 Zn의 매장량으로 인한 원자제의 가격상승과 습식 도금과정의 환경오염 물질 배출 문제가 기존 Zn 코팅의 약점으로 지적되고 있다. 따라서 새로운 원소의 첨가로 인한 Zn의 사용량 감소나 친환경적인 공정방법을 적용하는 연구가 대두되고 있다. 최근의 연구 결과에 따르면 Zn-Mg 합금이 다른 Zn계 합금에 비해 내식성이 우수하며, 이와 같은 우수한 내식성은 $Mg_2Zn_{11}$, $MgZn_2$와 같은 Mg-Zn 이원계의 합금상에 의한 것으로 알려져 있다. 따라서 본 연구에서는 친환경적인 비대칭 마그네트론 스퍼터 공정을 활용하여 다양한 공정조건 하에서 Zn-Mg 박막을 합성하여 최적의 공정 조건을 도출하고자 하였다. Zn-Mg 박막 합성 시 Mg타겟의 조성은 3~10 wt.%로 변화하였으며 Zn-Mg 합금 타겟의 온도를 제어하여 박막의 Mg 조성과 타겟 온도가 Zn-Mg 도금강의 내식성 및 밀착성에 미치는 영향을 평가하였다. 합성된 Zn-Mg 박막은 FE-SEM, EDS, XRD를 사용하여 미세조직, 두께, Mg 조성, 합금상 등을 분석하였으며, 염수분무시험 및 0T 굽힘 시험을 활용하여 Zn-Mg 박막의 내식성 및 내식성을 비교 분석하였다. FE-SE및 EDS분석 결과 Zn-Mg 박막의 Mg 조성은 합금 타겟의 조성이 증가함에 따라 증가하였으며, Mg 함량이 증가할수록 미세구조가 치밀하게 변화하였다. 또한 Zn-Mg 박막 합성 중 타겟의 온도가 상승할수록 박막의 치밀도는 감소하였다. XRD분석 결과 박막을 이루는 주요 합금상은 Zn상과 $Mg_2Zn_{11}$상이며 본 연구에서는 증착 조건에 따른 합금상의 큰 변화는 보이지 않았다. 염수분무실험 및 밀착성 평가 결과 박막의 미세조직이 치밀할수록 Zn-Mg 도금강의 내식성은 향상되었으나, 밀착성은 오히려 감소하는 경향을 나타내었다. 이러한 결과는 Zn-Mg 박막이 치밀한 미세구조일수록 부식환경에서의 강판에 대한 보호 효과는 증가하는 반면, 변형 시 박막의 파괴로 인한 박리 현상이 가속되기 때문으로 판단된다.

• Proceedings of the KAIS Fall Conference
• /
• 2004.06a
• /
• pp.281-284
• /
• 2004

본 연구에서는 분무열분해 공정에 의해 폐산용액으로부터 평균입도 100nm 이하의 나노 분말을 제조하였다. 용액 내의 Fe 성분의 농도가 20 g/$\iota$로부터 200 g/$\iota$로 증가됨에 따라 생성된 분말의 입도는 30 nm로부터 60 nm 까지 점점 증가하는 반면 입도분포는 더욱 불규칙하게 나타나고 있었다. 또한 용액 내의 농도 증가에 따라 $NiFe_2O_4$ 상의 생성비율이 현저히 증가하고 있었으며, 입자들의 비표면적은 현저히 감소하였다. 공기압력이 $1 kg/cm^2$까지는 분말의 평균입도는 80$\~$100 nm로 공기압력의 증가에 따라 분말들의 평균입도는 현저한 변화를 나타내지 않았으며, 생성된 상들의 비율의 현저한 변화도 나타나지 않았다. 공기압력이 $3kg/cm^2$로 증가하는 경우에는 평균입도가 약 70 nm로 감소하였으며 $NiFe_2O_4$의 생성비율도 감소하였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.2
• /
• pp.65-72
• /
• 2001

In order to improve the performance of a free power turbine type gas turbine engine by injecting the atomized water into a compressor inlet., a study on Moisture Air Turbine (MAT) cycle was proposed. Compressor work by air-water mixtures in phase change was theoretically considered, and it was found that the water evaporation might reduce the compressor work. Cycle model calculations predicted that power increments of 16.2%, 14.9% and 12.6% by 1.0% water to the air flow rate at the compressor intake with rotational shaft speeds of 1000, 1210, 1350 rps were obtained, and also thermal efficiency due to the reduction of compressor work was improved.