• 한국기계가공학회지
• /
• 제8권3호
• /
• pp.68-73
• /
• 2009

This paper deals with the dynamic characteristics of the impeller shaft model which is the most important part in developing the resin mixing machine. The can is rotating by air motor in mixing machine. Then the end of shaft is fixed. The bearing support is to increase the fundamental natural frequency. The natural frequency analysis using finite element analysis software are performed on the imported commercial impeller shaft model. This paper presents calculated bearing stiffness of Soda, Harris and modified Harris formula considering contact angle according to bearing supported position. The most important fundamental natural frequency of the impeller shaft except bearing support is around 13.932 Hz. This paper presents one bearing and two bearings support position to maximize the 1st natural frequency. The maximized fundamental natural frequency is around 48.843 Hz in one bearing support and 55.52 Hz in two bearings support.

• 한국분말재료학회지
• /
• 제26권5호
• /
• pp.421-431
• /
• 2019

In this study, the formation, microstructure, and wear properties of Colmonoy 88 (Ni-17W-15Cr-3B-4Si wt.%) + Stellite 1 (Co-32Cr-17W wt.%) coating layers fabricated by high-velocity oxygen fuel (HVOF) spraying are investigated. Colmonoy 88 and Stellite 1 powders were mixed at a ratio of 1:0 and 5:5 vol.%. HVOF sprayed self-fluxing composite coating layers were fabricated using the mixed powder feedstocks. The microstructures and wear properties of the composite coating layers are controlled via a high-frequency heat treatment. The two coating layers are composed of ${\gamma}-Ni$, $Ni_3B$, $W_2B$, and $Cr_{23}C_6$ phases. Co peaks are detected after the addition of Stellite 1 powder. Moreover, the WCrB2 hard phase is detected in all coating layers after the high-frequency heat treatment. Porosities were changed from 0.44% (Colmonoy 88) to 3.89% (Colmonoy 88 + ST#1) as the content of Stellite 1 powder increased. And porosity is denoted as 0.3% or less by inducing high-frequency heat treatment. The wear results confirm that the wear property significantly improves after the high-frequency heat treatment, because of the presence of well-controlled defects in the coating layers. The wear surfaces of the coated layers are observed and a wear mechanism for the Ni-based self-fluxing composite coating layers is proposed.

• 한국통신학회논문지
• /
• 제12권5호
• /
• pp.527-534
• /
• 1987

진동에 관한 비선형 1계연립미분방정식을 아나로그 시뮬레이션으로 2상전압제어발진을 시켜 유용성을 확인하였다. 2상신호를 각각 제곱하여 합성하는 부분과 곱셈부분의 실제회로 구성시 복잡하고 가격이 높아지므로 정류 회로와 스위칭회로로 대치하여 회로의 단순화와 가격 저렴화를 이루었다. 본 논문에서 제시된 회로는 제어 압력전압에 주파수가 정확한 비례관계를 가졌고, 응답 속도가 비교적 빠르고 또한 위상오차가 매우 적었으며 주파수비가 10:1 이상에서도 저왜율과 정진폭으로 동작하였다.

• International Journal of Knowledge Content Development & Technology
• /
• 제9권4호
• /
• pp.7-29
• /
• 2019

The study was carried out to investigate the influence of demographics and social media use on perceived academic stress of secondary school students in St. Thomas Aquinas College, Akure, Nigeria. This was achieved using five research questions and four null hypotheses. The population of the study consisted of 1,107 students at ISCED level 3, out of which 286 were selected based on the Israel (2003) model for determining sample size. The Ex-Post Facto (EPT) research design of the correlational type was employed to investigate the study while questionnaire was used for data elicitation. Out of the 286 copies distributed, 192 (67% response rate) were retrieved and analyzed using descriptive statistics (frequency, percentage, mean and standard deviation) and inferential statistics (correlation and multiple regression). The findings revealed that there is high frequency of social media use among secondary school students, majorly for meeting new friends and chatting. The perceived academic stress (PAS) of the students was found to be moderate. Of the three demographics considered, only class had significant influence on PAS. Use of social media did not have significantly influence on PAS of the students. When combined, demographics and social media use predicted PAS; and when considered relatively, of the independent variables, only class as an aspect of demographics predicted PAS. Therefore, the authors concluded that PAS of secondary school students is not directly influenced by demographics (except for class) and social media use. Based on the study's conclusion, recommendations were made.

• Journal of the korean society of oceanography
• /
• 제34권1호
• /
• pp.22-35
• /
• 1999

The response of the tidal waves to friction effect is investigated in terms of deformation of Kelvin and Poincare modes, The 1st Poincare mode does not exist over the low frequency region less than the critical frequency of omega ${\omega}$${\sqrt{2f}}$, with ${\gamma}$/f=0.0, but the mode comes to exist in the presence of friction. When friction exists and its magnitude increases, the wave number increases, indicating that the wave length of the Poincare mode becomes increasingly short with increasing friction. The damping coefficient gradually increases with increasing friction over the high frequency region, but the trend is reversed over the low frequency region. In case of Kelvin wave the present study substantiates the characters of Kelvin wave examined by Mofjeld (1980) and Lee (1988). Based on the examination of frictional effects on the tidal wave propagation, the co-oscillating tides in the Yellow Sea are examined by considering both the head opening and bottom friction effects. As friction is introduced and increased in addition to partial opening at bay head, the location of the amphidromic point near the Shantung Peninsula moves more southwestward. This southwestward movement of the amphidromic point is increasingly compatible with the observed location of Ogura's or Nishida's tidal chart of the M$_2$ tide.

• 한국산업융합학회 논문집
• /
• 제25권6_3호
• /
• pp.1155-1163
• /
• 2022

This study proposes a technology to ensure the seismic stability of a 1,000 kW diesel engine-type emergency generator by applying a seismic isolated bed system. The technology allows the static analysis by making the first natural frequency of the installed entire emergency generator larger than the earthquake cutoff frequency of 33 Hz. First a three dimensional model for the generator was made with simplification for mode analysis. A new bed system with springs, shock absorbers, stoppers was then devised. Next, The mode analysis for the finite element model equipped by the bed system was performed. the 1^st natural frequency above 33 Hz, the seismic safety cutoff frequency, was calculated to be 152.92 Hz. Finally, based on the seismic stability theory, the von-Mises equivalent stresses derived by structural analysis under the Upset and Faulted conditions were 0.01603 Mpa, and 32.06 Mpa, respectively. so seismic stability was confirmed.

• Journal of Microbiology and Biotechnology
• /
• 제3권1호
• /
• pp.24-30
• /
• 1993

In order to develop a novel yeast which produces the charateristic aroma of soy sauce, a protoplast fusion between Zygosaccharomyces rouxii WFS4 and Torulopsis versatilis IAM 4993 was carried out. Auxotrophic mutants as selective markers were obtained from Zygosaccharomyces rouxii and Torulopsis versatilis by treatment of N-methyl-N -nitro-N-nitrosoguanidine. The conditions of the protoplast formation and the regeneration for fusion were examined. The protoplast fusion using polyethylene glycol 4000 led to the fusion frequency of $4~5{\times}10^{-7}\;cells/ml$. Among fusants, a fusant ST723-F31 presented the best results in terms of the aromaticity of fragrance, the growth pattern, the resistance against salt and the degree of growth according to pH. It makes easy to control the production and the balance of aroma components so that it gives a good flavor, shortens the fermentation period and, simplifies the preparation process when using a bioreactor into which fusant is immobilized.

• 한국물환경학회지
• /
• 제26권5호
• /
• pp.747-753
• /
• 2010

A series of experiments with a laboratory scale ultrasound treatment system for MTBE polluted groundwater was performed to increase the efficiency of MTBE degradation in groundwater. This study evaluated several factors to increase the efficiency of MTBE treatment for artificial and natural groundwater. The treated volume of groundwater, ultrasound frequency and power, and pollutant concentrations have been changed to evaluate its effects on the degradation efficiency of MTBE in batch and continuous flow reactor. For the specific experimental conditions on this paper, MTBE degradations are more efficient at 580 kHz than those at 1 MHz. The efficiency of MTBE degradation is proportional to the intensity of ultrasound power per unit volume of MTBE polluted groundwater. The concentration of ions in groundwater does not much affect the efficiency of MTBE degradation. The $1^{st}$ order degradation constant of MTBE for different power per unit volume at 580 kHz shows linear relationship at same concentration. The $1^{st}$ order degradation constant for 0.1 mM MTBE solution is higher than that for 1 mM MTBE solution. These experimental results could be helpful to seek optimal conditions for relatively large volume of polluted groundwater treatment.

• 한국전자파학회논문지
• /
• 제11권6호
• /
• pp.1006-1014
• /
• 2000

1차 방사기 이동만으로 전 방향에 대해 빔포인팅이 용이한 르네베르그렌즈 안테나를 절반의 르제베르그렌즈 단면에 반사판 부착으로 소형화, 경량화한 반구형 르네베르그렌즈 안테나(주파수 9.375GHz, -3dB 빔 폭 6$^{\circ}$, 렌즈 직경 30.3cm(약 10λ))를 설계 제작하였다. 특성측정결과 -3dB 빔 폭 E면 6.1$^{\circ}$, H면 5.5$^{\circ}$로 설계치대로 양호한 빔 특성이 얻어졌으며, 이득은 약 26dBi(균일분포에 대한 개구효율 $\pi$=44.97%)로 1차 방사깅니 구형마이크로스트립 안테나보다 20.4dB 증가되었다. 또한, 1차 방사기의 근사패턴을 형성시켜 이를 2차 개구면 소스로 한 원방계패턴 계산결과 설계치와 일치함을 확인하였다. 한편, 우선.좌선원편파 특성을 갖도록 1차 방사기를 설계하여 원편과 반구형 르네베르그렌즈 안테나를 구성하였다. 특성 측정결과 -3dB 빔 폭 5.8$^{\circ}$, 사이드로브 -15.3dB, 편파분리도 25dB, 축비 0.74dB, 축비 2dB 이하의 주파수범위 약 1.4GHz(14.9%)로 비교적 광대역의 양호한 원편파특성이 얻어졌다.

• 유기물자원화
• /
• 제4권1호
• /
• pp.33-42
• /
• 1996

예취빈도와 액상구비의 시용수준에 대한 Reed canarygrass의 반응을 조사하여, 잠재생산성의 증대를 위한 경제적이고 합리적인 적정 예취빈도와 액상구비의 시용수준을 추정하고자 하였다. 예취빈도별 연간 건물수량에 대한 예취번초의 상대수량은 3회 예취구에서 2번초, 4회 예취구에서 3번초 및 5회 예취구에서는 4번초에서 다른 예취번초에 비해 가장 높은 상대수량을 나타내었다. 무시용구의 연간 건물수량은 예취빈도에 따라 6.4~7.5 ton/ha의 범위를 나타내었으며, 3회 예취구에서 가장 많은 연간 건물수량을 나타내었다. 액상구비의 시용수준이 증가됨에 따라서 연간 건물수량은 증가되었다. 즉, 3회 예취구에서는 연간 180 kg, 4회 예취구에서는 연간 120 kg 및 5회 예취구에서는 연간 300 kg로 증시하였을 때, 무시용구에 비해 유의하게 높은 건물수량을 나타내었다. 액상구비의 건물생산효율 (kg DM/kg N)은 3회 예취구의 120 kg/ha/cut, 4회 예취구의 30 kg/ha/cut 및 5회 예취구의 90 kg/ha/cut에서 각각 16.8, 25.4 및 10.4 kg 의 가장 높은 건물을 생산하였고, 시용시기에 따른 건물생산효율은 3회 예취구에서 1번초, 4회와 5회 예취구에서는 2번초에서 가장 높았다. 경제적 액상구비의 질소시용수준은 3회 예취구에서 462.7~525.3 kg/ha, 4회 예취구에서 353.1~423.2 kg/ha 그리고 5회 예취구에서 380.1~424.4 kg/ha의 범위를 나타내었다.