• 한국자동차공학회논문집
• /
• 제20권3호
• /
• pp.45-51
• /
• 2012

This work was investigated 2-stage injection strategy on combustion and emissions in a direct injection compression-ignition engine fueled with DME. Single cylinder engine was equipped with common rail. Injection pressure was 700bar, dSOI between the main injection and the pilot injection was varied. Diesel was used as compared fuel of DME in all cases. The results was shown that maximum pressure was higher than all cases and its amount of DME and diesel was similar. Regardless the pilot injection, the main fuel injection timing was same. The heat release rate of the main injection for diesel was high while that of pilot injection for DME was high. The THC was very low regardless of the fuel type and injection strategy. In the single injection, NOx was increased to retard of main injection timing regardless of the fuel type. NOx emissions was decreased with the retardation of the main injection timing regardless of the fuel type in the case of 2-stage injection strategy.

• Elastomers and Composites
• /
• 제47권4호
• /
• pp.341-346
• /
• 2012

사출성형은 고분자성형법 중에서 가장 광범위하게 활용되고 있다. 사출성형은 전형적인 사출성형 외에 가스사출, 물사출, 그리고 사출압축성형 등과 같이 특수한 사출성형방법들이 쓰인다. 사출압축성형은 사출과 압축공정이 합쳐진 것으로 균일한 물성 및 성형의 정밀도를 향상시키기 위하여 사용된다. 또한 사출압축은 잔류응력을 줄이는데도 효과적으로 사용되고 있다. 본 연구에서는 성형품의 형상에 따라 다양하게 나타나는 사출압축성형의 특성에 대해서 컴퓨터 해석을 통해 분석하였다. 성형품에 벽이 있는 제품은 벽의 두께가 압축의 방향과 직각이므로 압축효과가 작게 나타났다. 사출압축성형을 일반사출성형과 비교하였을 때 수축의 균일성 및 수축량 또는 성형수축률이 작게 나타나서 정밀성형에 유리하게 나타났다. 실험계획법을 통해 실제로 제작되고 있는 렌즈에 대해서 최적 사출압축조건을 구하고 이의 결과를 사출성형의 결과와 비교분석하였다.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제25권1호
• /
• pp.12-24
• /
• 2020

This study was conducted to examine an artificial recharge system, which was considered to be an alternative for securing additional groundwater resources in a high-density greenhouse region. An injection well with a depth of 14.0 m was placed in an alluvial plain of the zone. Eight monitoring wells were placed in a shape of dual circles around the injection well. Aquifer tests showed that the aquifer was comprised with high-permeable layer with hydraulic conductivities of 1.5×10^-3~2.4×10^-2 cm/sec and storage coefficients of 0.07~0.10. A step injection test resulted in a specific groundwater-level rising (Sr/Q) values of 0.013~0.018 day/㎡ with 64~92% injection efficiencies. Results of the constant-rate injection test with an optimal injection rate of 100 ㎥/day demonstrated an enormous storage capacity of the alluvial aquifer during ten experimental days. To design an optimal recharge system for an artificial recharge, the high-permeable layer should be isolated by dual packers and suitable pressure should be applied to the injection well in order to store water. An anisotropy ratio of the alluvial aquifer was evaluated to be approximately 1.25 : 1 with an anisotropy angle of 71 degrees, indicating intervals among injection wells are almost the same.

• 대한기계학회논문집A
• /
• 제25권10호
• /
• pp.1575-1582
• /
• 2001

Injection molding is widely used in producing various plastic parts due to its high productivity, and the demand for injection molded products with high precision is increasing. To achieve successful product quality and precision, the design of gating and runner system in injection mold is very important because it influences the melt flow into the cavity. Some deflects, such as weld lines and overpacking, can be effectively controlled with proper selection of gate locations. In the present study, the design of gate locations in injection molding of a dashboard fur automobiles was carried out with CAMP mold, a PC-based simulation system for injection molding. A dummy runner system was developed to simulate a runner system in order to increase the efficiency of the analysis procedure. The numbers and locations of gates were iteratively determined in the present investigation. In this procedure, an acceptable design was obtained in terms of reducing the maximum pressure and clamping force.

• 한국자원식물학회지
• /
• 제20권6호
• /
• pp.548-552
• /
• 2007

This research is the basic research to develop new anti-inflammatory medicine by feeding Scutellariae Radix extract to lipopolysaccharide(LPS) exposed rats, and analyzed it's effect on inflammatory response by LPS derivation. As a result, Plasma interleukin-$1\beta(IL-1\beta)$ and Plasma interleukin-6(IL-6) concentration showed the highest point at 5h after LPS injection, and in this time, the concentration of $IL-1\beta$ and IL-6 in the Scutellariae Radix extract groups at 200mg/kg and 300mg/kg showed lower values than that of control group. Plasma tumor necrosis $factor-\alpha(TNF-\alpha)$ concentration after LPS injection showed the highest point at 2h and showed similar level till at 5h. $TNF-\alpha$ concentration at 2h after LPS injection showed the low value only in the Scutellariae Radix extract 300mg/kg group compared to others, and in 5h, the all Scutellariae Radix extract groups showed lower value than that of the control group. Plasma interleukin-10(IL-10) concentration increased at 2h after LPS injection and reached the highest at 5h. After LPS injection the IL-10 concentration at 2h, the Scutellariae Radix extract injection group at 300mg/kg showed higher value than that of the others, and in 5h after LPS injection, Scutellariae Radix extract 200mg and 300mg groups showed higher value than the control group. Concluding from the above results, in inflammatory response by LPS derivation, the Scutellariae Radix gives positive effect.

• 한국구조물진단유지관리공학회 논문집
• /
• 제10권1호
• /
• pp.115-122
• /
• 2006

현재 콘크리트 구조물의 보수에서 품질의 검사 기준이 없는 상태에서, 단순한 경험에 의한 보수는 문제점을 가지고 있다. 이 문제점을 개선하기 위하여 이 논문은 균열폭과 주입량, 균열폭과 주입시간, 균열폭과 주입압력, 균열폭과 주입압력과 주입시간, 구조물 규모와 주입량, 구조물 별 균열 위치와 주입량, 균열폭 및 구조물 두께와 주입시간과의 관계를 분석하였다. 분석한 결과에서 얻은 자료는 콘크리트 구조물의 보수에 대한 체계적인 품질관리에 도움이 될 것이라 생각한다.

• 한국분무공학회지
• /
• 제25권3호
• /
• pp.95-102
• /
• 2020

Six shear coaxial injectors for a 3 tonf-class liquid rocket engine using oxygen and methane as propellants were designed and manufactured by considering geometric design parameters such as a recess length and a taper angle. Cold-flow tests on the injectors were performed using water and air as simulants. By changing the water mass flow rate and air mass flow rate, the injection pressure drop under single-injection and bi-injection was measured. The discharge coefficients through the injector oxidizer-side and fuel-side were calculated and the discharge coefficient ratio between bi-injection and single-injection was obtained. Under single-injection, the recess served to reduce the injection pressure drop on the injector fuel-side. For the injectors without recess, the discharge coefficients under bi-injection were almost the same as those under single-injection. However, for the injectors with recess, the taper angle and bi-injection had a significant effect on the discharge coefficient.

• 설비공학논문집
• /
• 제27권6호
• /
• pp.300-306
• /
• 2015

For an asymmetric scroll compressor for heat pump application, a numerical simulation was carried out to investigate the effects of injection port design on the compressor's performance under gas injection. To validate the simulation, the numerical results were compared with experimental results obtained from a scroll compressor with a base injection port design. There was good agreement between simulation and experimental results, with around a 1% difference in the injection mass flow rate when the injection pressure was below $12kgf/cm^2A$ for the heating mode. Various injection port angular positions were numerically tested to yield better injection performance. The largest improvement in heating capacity was obtained at angles of $240^{\circ}$ and $200^{\circ}$ inward from the scroll wrap end angle for low-temperature and standard heating conditions, respectively, while the maximum COP improvement was at $365^{\circ}$ and $280^{\circ}$, respectively. A considerable improvement in cooling capacity was also found at the injection port angle of $240^{\circ}$.

• 한국구조물진단유지관리공학회 논문집
• /
• 제10권6호
• /
• pp.191-197
• /
• 2006

본 논문은 터널 콘크리트 구조물의 보수를 위한 무기계 균열주입기술의 표준화에 관한 연구이다. 본 연구를 위하여 균열보수공사가 필요한 터널 라이닝 및 박스 구조물을 선정하여, 균열폭에 따른 주입량, 주입시간 및 주입압력, 주입압력과 주입시간, 구조물 규모에 따른 주입량, 구조물별 균열 위치에 따른 주입량, 균열폭 및 구조물 두께와 주입시간의 관계에 관하여, 현장 조사와 시험평가를 수행하여 구조물의 종류 및 균열의 크기에 따른 균열보수재의 주입압력, 주입량 및 주입시간 등을 명확히 파악하였다.

• 한국분무공학회지
• /
• 제24권3호
• /
• pp.114-121
• /
• 2019

The effect of injector driving current pattern on fuel injection rate of solenoid diesel common rail injector was studied by computer simulation. The time resolved fuel injection rate and injected quantity per stroke of a common rail injector driven with the five current patterns were computer simulated. The fuel injection rate and injected quantity per stroke according to the rail pressure and fuel injection period were also computer simulated. When the common rail injector was driven with the five driving current patterns of peak & hold, there was no difference in the fuel injection rate in the peak section regardless of all the current patterns of the five cases. On the other hand, the magnitude of the hold current value influenced the injection rate and injected quantity per stroke. That is, in the current pattern of three cases where the hold current value is equal to or more than a constant value of the peak current value, the fuel injection rates for the given common rail rail pressure and injection period are same one another. On the other hand, the current pattern of the two cases, in which the hold current value is smaller than a certain value, there is a large fluctuation in the fuel injection rate.