• Clinical Pain
• /
• 제20권2호
• /
• pp.59-69
• /
• 2021

Patients with pain, numbness, and weakness in their elbows, wrists, and hands often need proper rehabilitation treatments. Among them, musculoskeletal injection therapy should be performed after a full evaluation of the patient, taking into account history and physical examination leading to clinical diagnosis. General rules such as accurate diagnosis and injection materials selection are used to achieve maximum benefit with minimal side effects. During injection, patient location, aseptic care, penetration techniques, follow-up and follow-up care must be maintained. Specific techniques may vary depending on the type, lesion, and location of the injection therapy. For optimal effectiveness, physician should inject directly into the lesion and avoid the injection of surroundings as much as possible. Therefore, ultrasound-guided injections are needed to accurately inject. These conditions and other conditions of the hands, wrists, and elbows can be effectively diagnosed and treated with diagnostic ultrasound and ultrasound-guided injections.

• 한국정밀공학회지
• /
• 제10권3호
• /
• pp.231-238
• /
• 1993

Mold-marking industries currently demands to reduce the tooling costs and time in mold making and to improve the productivity and quality in injection molding process. These problems can be easily solved by the laminated injection mold which is made by laser cutting metal sheets and bonding them by the brazing. Comparing with the conventional mold making technology which mainly depends on the machining, the new thchnology enables an arvitary design of cooling circuit whithout any restrictions of geometry. Therefore, it will offer high production tata of the injection molding processes. This paper evaluates the conventional and laminated injection mold making processes with a simple molding geometry, and also the cooling efficienty of the kinds of mold with the filling and cooling analyses. The results show that the laminated injection mold process takes much shorter time in tooling and cooling, and distributes temperatures more uniformly than the conventional one.

• 한국분무공학회지
• /
• 제10권1호
• /
• pp.17-23
• /
• 2005

Even though a relatively complete knowledge base has been established for diesel sprays, much of the knowledge cannot be directly translated to correlate the characteristics of gasoline spray. The macroscopic characteristics of gasoline impingement spray was investigated with photographic and image processing technique by Particle Motion Analysis System. The injector with single hole nozzle diameter of 0.28 mm was used in this experiment and the injection duration was selected as 10 msec. The injection pressure with 0.3, 0.35, and 0.4 MPa, impingement distance or 70, 100 and 130m, impingement angle or 0.15, 30 and $45^{\circ}$ were employed for the variables to affect the spray characteristics of impinging spray. It is clear that there is the analogy on the spray tip penetration between the gasoline impinging jet and diesel free jet. The spray tip penetration of impinging gasoline spray is proportional to the quarter power of the time after start of injection. The maximum height of impinging gasoline spray is also proportional to the quarter power of the time regardless of impingement distance, impingement angle and injection pressure. In addition, the effect of impingement angle on the spray tip penetration is significant according to the time after start of injection, even though there is minor effect in the initial stage of time after start of injection. Moreover, there is no remarkable effect of injection pressure on the spray tip Penetration under the experimental condition used in this study.

• 소성∙가공
• /
• 제12권1호
• /
• pp.3-10
• /
• 2003

The formation of surface defects associated with Jotting in injection molding is related to the geometries of cavity and fate, operational conditions and the rheological properties of polymer. In this study we have examined jetting phenomena in injection molding process for the throe kinds of PCs which have different molecular weights and structures, PBT and PC/ABS alloy with several injection speeds. We have used various cavity shapes those are tensile, flexural and impact test specimens with various gates and cavity thicknesses. Through this study we have observed that the jetting is related to the dic swell of material. This means that the jotting is strongly affected by the elastic flow property rather than the viscous flow property in viscoelastic characteristics of molten polymer. Different resins have different elastic properties, and elastic flow behavior depends on the shear rate of flow, i.e. injection speed. Large die swell would eliminate jetting however, the retardation of die swell would stimulate jetting. In the point of mole design, reducing the thickness ratio of cavity to gate can reduce or eliminate jetting regardless of amount of elasticity of polymer melt.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제29회 추계학술대회논문집
• /
• pp.293-296
• /
• 2007

호주국립대학의 T3 자유충격파관을 이용하여, 마하수 3.7의 유입 유동에 대해 비분사유동, 공동이전 경사분사유동, 공동내부 평행분사유동, 공동내부 역분사유동에 대해 주파수를 확인하고, 공동 유동 특성을 살펴보았다. 비분사유동은 고조파 형태의 주파수가 나타나지 않았으나 10 kHz 부근에서 비교적 큰 압력 스펙트럼이 나타났다. 공동 이전 경사분사는 공동의 앞전에서 박리되는 전단층의 두께를 증가시켜 공동 뒷전에서 발생하는 유동의 진동 현상을 현저히 감소시켰다. 공동 내부 평행분사는 공동의 뒷전에 분사 유동이 직접 부딪히게 되고, 공동의 진동 현상을 오히려 증가시켰다.

• 한국자동차공학회논문집
• /
• 제25권1호
• /
• pp.35-41
• /
• 2017

The use of engineering plastics in automotive components is increasing with the trend towards improving the car strength and reducing weight. Among the different choices of materials, engineering plastic emerged as the necessary material for achieving lower costs, reduced weight and improved production efficiency. To produce the automotive parts, it is important to predict defect and validation of injection molding prior to design. Injection molding analysis and structural analysis are widely applied as a part of the design process when developing automotive parts. Injection molding analysis, in particular, involves a highly complicated mechanism that requires deep knowledge of polymer properties as well as an analytic approach different from that used for a general isotropic material when the molded material is used as a structural material. This is because the parts made of polymer have pre-stress factors such as intrinsic deformation and residual stress. The most important factors for injection molded plastic products are injection molding condition and cavity design, taking into account ease of molding, mass production and application. Despite optimal injection molding conditions and cavity design, however, glass fiber orientation is critically linked to strength reduction. The application of injection molding and structural coupled analysis provides a low-cost solution for product molding and structural validation, all prior to the actual molding. The purpose of this study involves the validation, pre-study, and solution of defect in injection-molded polymer automotive parts using the simulation software for injection molding and structural coupled analysis. Finally, this thesis provides validation of an injection molding and structural coupled analytic mechanism that can demonstrate the effect of glass fiber orientation on mechanical strength. Design improvement ideas for the injection molded product of PPS (Poly Phenylene Sulfide)+40% glass fiber are also suggested.

• Korean Journal of Acupuncture
• /
• 제38권4호
• /
• pp.250-266
• /
• 2021

Objectives : This study was conducted to suggest new alternative methods to improve pharmacopuncture and Korean medicine research by analyzing the injection route, pharmacological effect, and status studies of Chinese herbal injections. Methods : 130 types of marketed and licensed Chinese herbal injection were searched from National Medical Products Administration (NMPA) of China. CNKI, PubMed, EMBASE, and the 2020 edition of the Chinese Pharmacopoeia were used to collect additional information. 'Herbal injection' and 'Chinese herbal injection' were used as keywords. All data were collected mainly on the treatment of Chinese herbal injection. But data which were not related to the relevant research or Chinese herbal injection were excluded. Results : Intramuscular injection accounted for more than half of the single injection route (51%). Acupoint and intramuscular injections accounted for 55% of dual injection routes. Acupoint, intravenous, and intramuscular injections accounted for the largest proportion (76%) of the multiple routes of injections. As for the pharmacological effect, injection for cardiovascular diseases accounted for 29%. About the number of raw herbal materials, single herbal material was the most common. Twelve intervention studies all tested intravenous injections, and half of them investigated cardiocerebrovascular diseases. All were given by intravenous injection. In the side effect section, the most common symptoms were nausea and vomiting. Conclusions : Through the results, it is expected to be used for research and development of new pharmacopuncture and herbal medicine.

• 대한기계학회논문집A
• /
• 제26권11호
• /
• pp.2355-2363
• /
• 2002

The accompanying paper, Part 1, has presented the physical modeling and basic numerical analysis results of both the flow-induced and thermally-induced residual stress and birefringence in injection molded center gated disks. The present paper, Part II, has attempted to investigate the effects of various processing conditions of injection/compression molding process on the residual stress and birefringence. The birefringence is significantly affected by injection melt temperature, packing pressure and packing time. Birefringence in the shell layer increases as melt temperature gets lower. The inner peak of birefringence increases with packing time and packing pressure. On the other hand, packing pressure, packing time and mold wall temperature affect the thermally-induced residual stress rather significantly in the shell layer, but insignificantly in the core region. Injection/compression molding has been found to reduce the birefringence in comparison with the conventional injection molding process. In particular, mold closing velocity and initial opening thickness in the compression stage of injection/compression molding process have significant effect on the flow-induced birefringence, but not on tile thermal residual stress and the thermally induced birefringence.

• 대한기계학회논문집
• /
• 제11권1호
• /
• pp.145-153
• /
• 1987

본 논문에서는 예혼합동축분류화염에 있어서 재순환역 안으로의 기체(공기, 연료, 혼합기) 주입과 2차공기의 족회가 화염안정성, 화염형상 및 재순환역에 미치는 영향을 명확히 하였다.

• 한국자동차공학회논문집
• /
• 제10권4호
• /
• pp.23-32
• /
• 2002

Combustion and flame propagation characteristics of the liquid phase LPG injection (LPLI) engine were investigated in a single cylinder optical engine. Lean bum operation is needed to reduce thermal stress of exhaust manifold and engine knock in a heavy duty LPG engine. An LPLI system has advantages on lean operation. Optimized engine design parameters such as swirl, injection timing and piston geometry can improve lean bum performance with LPLI system. In this study, the effects of piston geometry along with injection timing and swirl ratio on flame propagation characteristics were investigated. A series of bottom-view flame images were taken from direct visualization using an W intensified high-speed CCD camera. Concepts of flame area speed, In addition to flame propagation patterns and thermodynamic heat release analysis, was introduced to analyze the flame propagation characteristics. The results show the correlation between the flame propagation characteristics, which is related to engine performance of lean region, and engine design parameters such as swirl ratio, piston geometry and injection timing. Stronger swirl resulted in foster flame propagation under open valve injection. The flame speed was significantly affected by injection timing under open valve injection conditions; supposedly due to the charge stratification. Piston geometry affected flame propagation through squish effects.