• Journal of Applied Biological Chemistry
• /
• v.56 no.1
• /
• pp.53-57
• /
• 2013

In here, we investigated the quantitative analysis method of indole-3-acetic acid (IAA) and indole-3-butyric acid (IBA) with liquid chromatography-mass/mass spectrometry (LC-MS/MS) or gas chromatography-MS. Two ways of clean-up process were investigated for LC-MS/MS instrumental analysis of IAA, but both a simple dilution and hydrophile-lipophile balance (HLB) solid phase extraction (SPE) were not met the optimal recovery rates for quantitative analysis. On the other hand, the clean-up method for GC-MS was finally optimized through HLB-SPE from 250-folds diluted sample and methylation with trimethylsilyl chloride in methanol for 4 h. The limit of detection for methyl ester of IAA and IBA were both 1.4 mg/L, and recovery rates showed 93-107% from the concentrated liquid fertilizer.

• Elastomers and Composites
• /
• v.37 no.2
• /
• pp.79-85
• /
• 2002

Ethyl-branched polyethylene [PE(2)] containing 2mole% ethyl branch and three ethylene-propylene rubbers (EPR's) having the same ethylene(E)-propylene(P) molar ratio(E/P=50/50) with different stereoregularity, that is, random EPR (r-EPR), alternating-EPR (alt-EPR) and isotactic-alternating-EPR (iso-alt-EPR) were mixed for the investigation or their properties depending on the stereoregularity. Crystallinity of the prepared blends decreased with increasing content of amorphous EPR because of a decrease in both the degree of annealing and kinetics of diffusion of the crystallizable polymer content. With blend composition, crystallinity was reduced with the stereoregularity in EPR. The thermodynamic interaction parameter(x) for the three blend systems approximately equals to zero near the melting point. These systems were determined to be miscible on a molecular scale near or above the crystalline melting point or the crystalline PE(2). From the measurement of $T_m$ vs. $T_c$, the behavior of PE(2) is mainly due to a diluent effect of EPR component. The spherulite size measured by small angle light scattering (SALS) technique depended upon blend composition, and stereoregularity of EPR. The size of spherulite was enlarged with the content of rubbery EPR and the decrease of stereoregularity in EPR.

• Economic and Environmental Geology
• /
• v.44 no.3
• /
• pp.193-201
• /
• 2011

The Geopung Cu deposit consists of two subparallel quartz veins that till the NE-trending fissures in Triassic Cheongsan granite. The quartz veins occur mainly massive with partially cavity and breccia. They can be followed along strike for about 500 m and varies in thickness from 0.2 to 2.2 m. Based on the mineralogy and paragenesis of veins, mineralization of quartz veins can be divided into hypogene and supergene stages. Hypogene stage is associated with hydrothermal alteration minerals such as sericite, pyrite, quartz, chlorite, clay minerals and sulfides such as pyrite, arsenopyrite, pyrrhotite, marcasite, sphalerite, stannite, chalcopyrite and galena. Supergene stage is composed of geothite. Fluid inclusion data from quartz indicate that homogenization temperatures and salinity of hypogene stage range from 163 to $356^{\circ}C$ and from 0.2 to 7.2 wt.% eq. NaCl, respectively. They suggest that ore forming fluids were progressively cooled and diluted from mixing with meteoric water. Sulfur (${\delta}^{34}S$: 4.3~9.2‰) isotope composition indicates that ore sulfur was derived from mainly magmatic source although there is a partial derivation from the host rocks. The calculated oxygen (${\delta}^{18}O$: 0.9~4.0‰) and hydrogen (${\delta}D$: -86~-69‰) isotope compositions suggest that magmatic and meteoric ore fluids were equally important for the formation of the Geopung Cu deposit and then overlapped to some degree with another type of meteoric water during mineralization.

• Korean Journal of Microbiology
• /
• v.25 no.4
• /
• pp.333-338
• /
• 1987

In order to establish the biological treatment system which can be used for treatment of waste aster from acetaldehyde plant, it was investigated optimum nutrient requirements and growth conditions by mixed culture of Micrococcus roseus AW-6, Micrococcus luteus AW-22, Microbacterium lacticum AW-38 and Microbacterium laevaniformans AW-41 as well as the effect of coagulants and neutralization reagents. Also, it was carried out the continuous culture as well as batch culture to treat the waste water by mixed culture of these strains. The COD removal rate was reached to maximum state for 96hrs culture at pH7.0 and $30^{\circ}C$ NaOH as the neutralization reagents was the most effective, but the coagulants had no effect on the COD remonal rate and the optimum dilution times for treatment were 10 fold. The COD removal rate was also increased by supplimenting 200 ppm $NH_{2}NO_{3}$, 50 ppm $KH_{2}PO_{4}$, 15 ppm $CaCl_{2}$ and 1 ppm $MgSO_{4} \cdot 7H_{2}O $ as additional nutrients. The removal rate coefficient $K_{1}$ on the batch culture was $4.5\times 10^{-6}$, and the detention time for BOD removal rate of 85% was approximately 45hrs. The COD of waste water was reduced to 15% of its initial value by the continuous culture. The COD and BOD of the effluents were to be about 60 ppm and 40 ppm, respectively, and final pH was 7.0.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.33 no.5
• /
• pp.899-904
• /
• 2004

The objectives of the experiment were to examine the effects of extrusion process variables on the yield of extruded ginseng extract and to determine the effect of ratio of extruded ginseng extract and microcrystalline cellulose on characteristics of spheronized granules by cold extrusion-spheronization process. Extrusion process variables observed were feed moisture (15, 22, 29%), die temperature (90 110 13$0^{\circ}C$) and screw speed (150 200, 250 rpm). The results showed that moisture content of dried ginseng significantly affected extraction yield (P<0.05). The less moisture content of the feed resulted in the higher yield of the extract. Moisture content of 15%, screw speed of 250 rpm and die temperature of 13$0^{\circ}C$ gave the highest yield of ginseng extract. Mean extraction yield of extruded ginseng using hot water extraction was greatly improved by extrusion process The extract yield of extruded ginseng was 43.5% which was higher than that of red ginseng (38.3%) and white ginseng (29.0%) produced by traditional process. It was possible to make from the mixture of microcrystalline cellulose (200 g) mixed with different concentration of 200 mL solution (0, 5, 20, 30 40 50 60% of ginseng extract with 59.2% dry solid) by using cold extrusion spheronization. When the concentration of ginseng extract Increased, the granulation yield was improved but friability and compression index were reduced. Ginseng extract such as saponin was completely released from spheronized granules in distilled water within 10 min. It can be concluded that spheroniged granule with ginseng extract could be packed in gelatin capsule since granules Possessed proper physical properties and quick release of saponin.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.32 no.3
• /
• pp.89-95
• /
• 2022

In this study, glassy carbon coating was performed on the graphite using a phenolic resin and a curing agent was mixed with ethylene glycol as an additive to form the uniform surface. The phenolic resin was dried and cured under the environments of hot air, then converted into a glassy carbon layer by pyrolysis at 500~1,500℃. FTIR, XRD, SEM analysis, and density/porosity/contact angle measurement were performed for characterization of glassy carbon. The pyrolysis temperature for high-quality glassy carbon was optimized to be about 1,000℃. As the content of the additive increased, the effect of reducing surface defects on the coated surface, reduction of porosity, increase of contact angle, and increase of density were investigated in this study. The method of forming a glassy carbon coating layer through an additive is expected to be applicable to graphite coating and other fields.

• Journal of agriculture & life science
• /
• v.50 no.4
• /
• pp.27-34
• /
• 2016

Sclerotium rolfsii is a well known broad host range soil borne plant pathogenic fungus and caused serious damage to various vegetable crops. To develop an effective biological control agent for S. rolfsii, an isolate which showed strong inhibitory effect on the mycelial growth of S. rolfsii was selected among the antagonistic bacterial isolates collected from vinyl-house soil. The bacterial isolate was identified as Bacillus amyloliquefaciens KBC1009 based on the morphological, physiological characteristics and by 16S rRNA sequence analysis. The growth conditions for B. amyloliquefaciens KBC1009 were optimized in LB media(pH7) by culturing at 30℃ for 72 hrs. Glucose and yeast extract were confirmed as the best carbon and nitrogen sources, respectively. In order to test the inhibitory effect of B. amyloliquefaciens KBC1009 to stem rot of pepper, green house experiment was conducted. Drench of 1/500 diluted bacterial suspension of B. amyloliquefaciens KBC1009(5×108 cfu/ml) to each pepper plant 3 times with 10 days interval showed 66.7% control effectiveness. These results suggest that B. amyloliquefaciens KBC1009 is one of promising biocontrol agent to control stem rot caused by Sclerotium rolfsii.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.1
• /
• pp.23-30
• /
• 2007

The ultimate objective of this study is to develop oxygen-enriched combustion techniques applicable to the system of practical industrial boiler. To this end the combustion characteristics of lab-scale LNG combustor were investigated as a first step using the method of numerical simulation by analyzing the flame characteristics and pollutant emission behaviour as a function of oxygen enrichment level. Several useful conclusions could be drawn based on this study. First of all, the increase of oxygen enrichment level instead of air caused long and thin flame called laminar flame feature. This was in good agreement with experimental results appeared in open literature and explained by the effect of the decrease of turbulent mixing due to the decrease of absolute amount of oxidizer flow rate by the absence of the nitrogen species. Further, as expected, oxygen enrichment increased the flame temperatures to a significant level together with concentrations of $CO_2$ and $H_2O$ species because of the elimination of the heat sink and dilution effects by the presence of $N_2$ inert gas. However, the increased flame temperature with $O_2$ enriched air showed the high possibility of the generation of thermal $NO_x$ if nitrogen species were present. In order to remedy the problem caused by the oxygen-enriched combustion, the appropriate amount of recirculation $CO_2$ gas was desirable to enhance the turbulent mixing and thereby flame stability and further optimum determination of operational conditions were necessary. For example, the adjustment of burner with swirl angle of $30\sim45^{\circ}$ increased the combustion efficiency of LNG fuel and simultaneously dropped the $NO_x$ formation.

• Economic and Environmental Geology
• /
• v.39 no.1 s.176
• /
• pp.9-25
• /
• 2006

Baekun gold-silver deposit is an epithermal quartz vein that is filling the fault zone within Triassic or Jurassic foliated granodiorite. Mineralization is associated with fault-breccia zones and can be divided into two stages. Stage I which can be subdivided early and late depositional stages is main ore mineralization and stage II is barren. Early stage I is associated with wallrock alteration and the formation of sulfides such as arsenopyrite, pyrite, pyrrhotite, sphalerite, marcasite, chalcopyrite, stannite, galena. Late stage I is characterized by Au-Ag mineralization such as electrum, Ag-bearing tetrahedrite, stephanite, boulangerite, pyrargrite, argentite, schirmerite, native silver, Ag-Te-Sn-S system, Ag-Cu-S system, pyrite, chalcopyrite and galena. Fluid inclusion data indicate that homogenization temperatures and salinity of stage I range from $171.6^{\circ}C\;to\;360.8^{\circ}C\;and\;from\;0.5\;to\;10.2\;wt.\%\;eq.$ NaCl, respectively. It suggest that ore forming fluids were cooled and diluted with the mixing of meteoric water. Also, Temperature (early stage I: $236\~>380^{\circ}C,\;$ late stage $I: <197\~272^{\circ}C$) and sulfur fugacity (early stage $I:\;10^{-7.8}$ a atm., late stage I: $10^{-14.2}\~10^{-l6}atm$.) deduced mineral assemblages from stage 1 decrease with paragenetic sequence. Sulfur ($2.4\~6.1\%_{\circ}$(early stage $I=3.4\~5.3\%_{\circ},\;late\;stage\;I=2.4\~6.1\%_{\circ}$)), oxygen ($4.5\~8.8\%_{\circ}$(quartz: early stage $I=6.3\~8.8\%_{\circ}$, late stage $I=4.5\~5.6\%_{\circ}$)), hydrogen ($-96\~-70\%_{\circ}$ (quartz: early stage $I=-96\~-70\%_{\circ},\;late\;stage\;f=-78\~-74\%_{\circ},\;calcite:\;late\;stage\;I=-87\~-76\%_{\circ}$)) and carbon ($-6.8\~-4.6\%_{\circ}$ (calcite: late stage I)) isotope compositions indicated that hydrothermal fluids may be magmaticorigin with some degree of mixing of another meteoric water for paragenetic time.

• Journal of the Korean Wood Science and Technology
• /
• v.8 no.1
• /
• pp.13-21
• /
• 1980

This experiment was carried out to investigate the effect of heating periods on the physical and mechanical properties of maple (Acer mono Max.) by oven heating and heating in water at 100$^{\circ}C$ for 0, 2, 4, and 6 days respectively. The results obtained are summarized as follows: 1. The green volume specific gravity due to oven heating decreased from 6 days of exposure, and that, due to heating in water decreased from 4 days of exposure. 2. The radial shrinkage due to oven heating decreased from 2 days of exposure, but that due to heating in water increased from 6 days of exposure. The tangential shrinkage due to oven heating decreased from 2 days of exposure, but that due to heating in water increased from 2 days of exposure. 3. The amount of water absorption due to oven heating decreased from 2 days of exposure, but that due to heating in water increased from 4 days of exposure. 4. The compressive strength pararelled to grain due to oven heating increased till 4 days of exposure but decreased from 6 days, and that due to heating in water decreased from 2 days of exposure. 5. The shearing strength pararelled to grain due to oven heating increased till 2 days of exposure, but decreased from 4 days of exposure, and that due to heating in water decreased from 4 days of exposure. 6. The bending strength due to oven heating increased till 4 days of exposure but decreased from 6 days, and that due to heating in water decreased from 6 days of exposure. The impact bending absorbed energy due to oven heating decreased from 4 days of exposure, and that due to hearing in water decreased from 2 days of exposure.