• Applied Chemistry for Engineering
• /
• v.24 no.3
• /
• pp.231-238
• /
• 2013

In this study, the $TiO_2$ nano spheres were synthesized by Sol-gel method to give an excellent UV-blocking effect and increase waste adsorption. The pH value was adjusted to obtain a superb UV-blocking effect and adsorption capacity due to the high surface area which is the characteristics of porosity. Base treated $TiO_2$ showed outstanding characteristics. The adsorption of gycerine onto the $TiO_2$ sample using TGA resulted in a high surface area of 1.16 mg/mg. This also showed a high reflectance in the UV-A region. In order to find the optimum dispersion, inorganic powder particles were maintained their sizes as 180 nm for about 6 months. The size of particles were measured using ester oil and silicon oil. Overall, the results reveal that $TiO_2$ has an excellent capability sunscreen in the UV-A region and skin waste adsorption.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.30 no.2
• /
• pp.344-349
• /
• 2001

The removal of chlorine from aqueous solutions on dried Chlorella vulgaris(DCV) and green tea powder(GTP) were investigated as a function of contact time, pH and initial chlorine concentration. Removal by DCV and GTP reached equilibrium after 3hrs and 0.5hr, respectively. Optimum removal pH values of DCV and GTP were determined as above 10. Both Langmuir and Freundlich adsorption models were suitable for describing the short-term removal of chlorine by DCV and GTP. According to Langmuir adsorption isotherms the maximum removal capacity of DCV (2.75mg $Cl_2/mg$) was nearly two times greater than those of GTP (1.53mg $Cl_2/mg$) and activated carbon (1.47mg $Cl_2/mg$). These results suggested that Chlorella vulgaris biomass might potentially be used as an alternative to traditional water treatment materials for removal of residual chlorine in drinking water or process waste-water.

• Fire Science and Engineering
• /
• v.26 no.4
• /
• pp.42-47
• /
• 2012

In the study, fire extinguishing concentration of $K_2CO_3$-Zeolite composite was measured. Zeolite composite is a porous adsorbent which has small particle size, low density and anti-catalytic effect. Scanning Electron Microscopy, X-Ray diffraction and thermal analysis were also conducted to investigate the structural properties of composite. The result showed that despite of weight ratio, the extinguishing concentration of the composite was lower than pure $K_2CO_3$. The extinguishing concentration of $K_2CO_3$-Zeolite composite which has weight ratio of 7 : 3 was 5.72 times lower than that of pure $K_2CO_3$ and 1.1 times lower than that of ABC powder. The SEM and XRD patterns showed that $K_2CO_3$ was adsorbed on the Zeolite properly, and through the thermal analysis, it was founded that the composite is more effective extinguishing agent than pure $K_2CO_3$.

• Journal of the Korean Electrochemical Society
• /
• v.25 no.2
• /
• pp.81-87
• /
• 2022

In this study, the effect of alkylamine on copper electroplating was analyzed using cyclic voltammetry. When water-soluble alkylamines were added to the plating solution, the reduction reaction of Cu²⁺ was inhibited. The inhibition effect of 1,12-diaminododecane has been investigated at various concentrations and conditions of the plating solution. 1,12-diaminododecane was protonated in the acidic plating solution, and therefore, it did not act as a complexing agent for Cu²⁺. Accordingly, it was confirmed that the inhibiton effect of 1,12-diaminododecane was attributed to adsorption on the Cu surface. The adsorption of 1,12-diaminododecane exhibits two characteristics: (i) protonation and subsequent electrostatic attraction with anions pre-adsorbed on Cu surface, and (ii) direct adsorption on Cu surface via amine functional group. The adsorbed 1,12-diaminododecane caused three-dimensional growth and grain refining, as well as the inhibition effect, during Cu electroplating.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.3
• /
• pp.547-556
• /
• 2000

A study have been conducted for the adsorption and desorption characteristics of Cu ion using manganese nodule as adsorbent. For 100 ppm Cu ion solution, the adsorbed amount of Cu ion was more than 90 % at equilibrium state. Adsorption was equilibrated in 42 hours the adsorption reaction was shown to be first order reaction. For the desorption reaction of Cu ion in the region of solution pH 3.5~9.5, the desorption was completed in the acidic region, but it has been decreased as the pH was raised. Also, the desorption rate was higher in the acidic region compared with alkaline region. The desorbed amount was decreased as the reaction temperature increased, therefore, the desorption reaction was thought to be exothermic. Also, several thermodynamic properties were calculated based on experimental results and compared with theoretically driven values. To see the effect of complexing agent on the desorption of Cu ion, EDTA was introduced and the des orbed amount increased in the presence of EDTA.

• Resources Recycling
• /
• v.20 no.6
• /
• pp.28-36
• /
• 2011

The adsorption of nickel(Ni) from sulfuric acid solution was carried out by ion exchange method. A series of batch tests in synthetic solutions were carried out using Lewatit Monoplus TP 220 resin. The following experimental parameters, such as temperature, shaking rate, reaction time, pH, resin dosage and concentration of nickel ions etc. were investigated to establish the effective optimum conditions of nickel adsorption. The solution pH(2.0~5.0) and shaking rate had little effects on the adsorption of nickel and adsorption time of 72hours was required to reach equilibrium. The experimental results show a good agreement with Feundlich isotherm and pseudo-second order reaction. The adsorption behavior of Ni obtained from synthetic solution was compared with that of waste electroplating solution. Elution of nickel from loaded resin increased with increase in $H_2SO_4$ concentration.

• Applied Chemistry for Engineering
• /
• v.21 no.5
• /
• pp.548-552
• /
• 2010

This study focused on the development of effective adsorbent to remove acetylenes for the purification of isoprene. The adsorbents with various pore sizes from $4{\AA}$ to $5{\AA}$ were prepared to investigate the effect of pore size on selective adsorption of acetylene as an impurity. The pore size of zeolite A was adjusted by ion-exchange between Na and Ca ions. The pore size of adsorbents has affected the removal of acetylenes selectively because of the kinetic diameter of acetylenes, such as 2-methyl-1-butyne-3-yen (IPA) and 2-butyne. In a batch adsorption experiment, 5A zeolite with pore size of $5{\AA}$ showed the highest removal capacity of 2-butyne. However, IPA was hardly removed from isoprene by the A-type zeolites. For the adsorption isotherm, modified Langmuir model was well fitted with 2-butyne adsorption. Moreover, the regeneration of adsorbent was carried out to determine optimum method. The adsorbent heated for 12 h at $300^{\circ}C$ was regenerated significantly.

• Journal of Soil and Groundwater Environment
• /
• v.8 no.3
• /
• pp.37-44
• /
• 2003

Fuel oxygenates, such as Methyl tertiary Butyl Ether (MTBE) is additive in gasoline used to reduce air pollution. Gasoline components and fuel additives can leak: form underground storage tanks. MTBE is far more water soluble than gasoline hydrocarbons like BTEX then it travels at essentially the same velocity as groundwater. MTBE in drinking water causes taste and odor problems. Therefore, the purpose of the this study is to examine the ability of ground tire to sorb MTBE in water. The study consisted of running both batch and column tests to determine the sorption capacity, the required sorption equilibration time, and the flow through utilization efficiency of ground tire. The batch test result indicated that ground tire can attain equilibrium sorption capacities about 0.5 mg of MTBE. The result of column test indicate that ground tire has on the 36% utilization rate. Finally, it is clear that ground tire represented an attractive and relatively inexpensive sorption medium for a MTBE. Authors thought that to determine the economic costs of ground tire utilization, the cost to sorb a given mass of contaminant by ground tire will have to be compared to currently accepted sorption media. The cost comparison will also have to include regeneration and disposal cost.

• Journal of the Korean Vacuum Society
• /
• v.20 no.1
• /
• pp.35-41
• /
• 2011

In this study, the interface soaking effect in InAs/GaAs strained-layer superlattice (SLS) on crystalline phase modulation has been analyzed by the x-ray diffraction (XRD) curve. The strain variation induced by As and/or Sb soaking was determined by the separation angle between the substrate peak and the 0th-order superlattice satellite peak in the XRD spectra. Contrated that the As/InAs soaking arises minor GaAs-like interfacial layer, the Sb/GaSb soaking induces InSb-like one. The Fourier-transformed curves of the Pendellosung interference oscillation shows that the optimum soaking times of As/InAs and Sb/GaSb are 2 sec and 12 sec, at which the highest crystallineity has, respectively. An anomalous twin-peak phenomenon that a satellite peak splits into two peaks was observed in the SLS structure co-soaked by As and Sb at InAs${\rightarrow}$GaSb interfaces. We suggest that it may be resulted from coexistence of two kinds crystalline phases of InAsSb and GaAsSb due to intermixing of In${\leftrightarrow}$Ga and Sb${\leftrightarrow}$As.

• Journal of the Korean Chemical Society
• /
• v.48 no.6
• /
• pp.590-598
• /
• 2004

The preconcentration and determination of trace Cu(II) and Pb(II) on calcium alginate beads in aqueous solution were studied. A calcium alginate beads were prepared by adding an alginic acid to sample solution contained Ca(II). Some following conditions were optimized: the pH of sample solution, amount of alginic acid, and stirring time for effective adsorption; the type and concentration of acid, and sonication time in an ultrasonic vibrator for the perfect de-sorption. A sample solution was prepared with Cu(II) and Pb(II) in DI water. And Ca(II) and ethanol was added into the sample solution. The pH of the final sample solution was controlled with buffer solution. The alginic acid were dispersed in the sample solution by a magnetic stirrer. This mixture was stored in room temperature for 30 min to form a calcium alginate. After the beads were filtered and washed on a membrane filter, the analytes were redissolved from the beads by an ultrasonic vibration of 10 minutes in 1.0M $HNO_3$ solution. The effect of diverse ions on the adsorption of analytes were studied. This procedure was applied for the analysis of two real samples. The recoveries in spiked samples were $90.4{\sim}104.3%$ for analytes.