• Journal of the Korean GEO-environmental Society
• /
• v.13 no.4
• /
• pp.53-59
• /
• 2012

In this study, strength and durability of a geo-polymer grout material(HIT) was investigated through unconfined compression strength tests(UCS)), scanning electron microscope(SEM), elution tests, and surface observations. UCS tests showed high initial strength and rapid continuous strength increments when compared to labile wasser glass(LW) and space grouting rocket system (SGR) grout materials, which showed strength reduction after 28 days. The higher strength was also reflected in SEM results which showed calcium silicate hydroxide(C-S-H) gels of the dense hydrate range, indicating higher strength and durability. Additionally, elution tests and grout surface observations showed HIT was in good condition and the decrease in weight was minor when under water for six months. LW and SGR showed the grout surface to be constricted and lower durability due to higher weight increase. These results and observations show HIT to be better suited for coastal structural applications than LW and SGR in long terms of strength and durability.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.9
• /
• pp.85-95
• /
• 2012

The method of using organic acid is more environment-friendly for it improves the strength of the ground. The method of proliferating microbes makes soil particle bonded, finally improves the strength of the ground and decreasing permeability. Although there has been the research on the effect of strength increasing, there has never been a research on the evaluation of field application. In this paper, through the light drop weight test, the dynamic cone penetration test, the field density test, the variation of strength was investigated in the mixed ground with organic acid for 56 days. As the results of the field test, it was found that the strength and stiffness of the ground increased with organic acid, and that through SEM-EDS, the precipitation of calcium carbonate made by specified microbe obviously increased with organic acid material and so the ground was improved. Therefore, the sustainable development of this method needs to be analysed more in the future.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.2
• /
• pp.57-62
• /
• 2013

A crack in a solid propellant increases the area of burning surface, which leads to excessive burning that causes motor failure. Therefore, it is necessary to evaluate fracture toughness of solid propellants. However, it is very difficult to measure fracture toughness of solid propellants because of the nonlinear mechanical behavior. In this study, evaluation of fracture toughness on a solid propellant was carried out under the assumption that the solid propellant is a linear viscoelastic material. Actual displacements from fracture toughness tests using CCT specimens were converted into pseudo-elastic displacements by using stress relaxation characteristics and fracture toughness was evaluated using ASTM E399 standard. Also, effects of test temperature and speed on the fracture toughness were considered.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.10
• /
• pp.5-12
• /
• 2011

Recently, NDS(Natural and Durable Stabilizer)method and other similar methods are composed of inorganic accelerating agent and the ultra-super fine cement have been studied as the ground improvement material in Korea. However, in the existing research, the chemical changing process of NDS in the strength development mechanism with the elapsed curing time and the principles of strength development did not give an explanation. For the popularization of the inorganic grout material, it determined that the mechanism verifying of the curing process had to be clearly preceded. Therefore, unconfined compression test, SEM and XRD analysis were performed by the elapsed curing time and were analyzed. In addition, the same trial for SGR method, that is the representative example of the water glass grout material, was selected as comparative target in order to distinguish properties of NDS more clearly. The result of experiment, the strength development mechanism of NDS could be investigated through the close correlation of the unconfined compression strength - SEM - XRD analysis, and excellence of a performance was confirmed.

• Polymer(Korea)
• /
• v.37 no.4
• /
• pp.455-461
• /
• 2013

Mar behavior and visibility were investigated by applying a constant load to various gloss-coated urethane-acrylate surfaces. Using a area-contact scratch tip which can apply a relatively low stress level to the coated surfaces, the mar damages were generated on the surfaces. When evaluating the mar-induced damage by means of delta-gloss (${\Delta}G$) and delta-luminance (${\Delta}L$) with existing test methodologies, an increase in constant load on the same gloss-coated surface leads to an increase in ${\Delta}G$ and ${\Delta}L$. However, these are not suitable for evaluating and comparing the surface damages of different gloss-coated samples because of a disagreement between the measured values and the mar visibility. It is shown that new mar test assessment proposed in this work not only can be used to quantitatively evaluate the mar damage, but also accounts for the correlation that the increases of the normalized gloss and luminance on coated surfaces correspond with an increase in the mar visibility.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.11a
• /
• pp.119-124
• /
• 2007

24" LCD Monitor용 LED BLU를 개발하기 위하여 1.5W R,G,G,B가 하나의 PKG에 들어있는 LED를 이용하여 Direct type의 Back Light Unit을 개발하였다. 방열 및 휘도 균일도를 고려하여 LED part를 설계, 개발 하였고 LED를 pulse로 구동하기 위하여 Switching circuit이 포함되는 구동회로 부분을 설계, 개발하였다. 또한 Color Sensor와 ICM (Integrated Color Management) IC를 사용하여 Color를 Control하는 제어회로 부분도 개발을 하였다. 제어회로 부분을 개발하기 위하여 MicroController를 사용하였으며 ICM IC와의 통신을 위한 부분도 개발하였다. 이러한 구성을 개발하여 시제품을 직접 제작하였다. 평가를 위하여 성능시험을 실시하였고 광학적인 평가도 시행하였다. 제작된 시제품은 $L558{\times}W359{\times}H30$으로 하였다. 휘도는 목표휘도를 이루었으며 균일도는 85% 이상이 되었다.

• Journal of Pharmaceutical Investigation
• /
• v.34 no.5
• /
• pp.379-383
• /
• 2004

Statistical interpretations in a bioequivalence trial are considered and studied when the missing observations occurred in $2\;{\times}\;2$ crossover experiment. Patel (1985) suggested the approximate test procedures for carryover effect and drug effect in $2\;{\times}\;2$ crossover design when some of data are missing in the second period. A modified Patel method is newly proposed to the bioequivalence trial and it is compared with the current method through the simulation study.

• Proceedings of the KSRS Conference
• /
• 2007.03a
• /
• pp.267-270
• /
• 2007

눈은 지표면의 물리과정에서 중요한 요소 중의 하나로 짧은 시간 동안에 많은 변화를 유도할 있다. 본 연구에 MODIS 채널자료를 이용하여 적설역에서 나타나는 단파적외 채널과 반사도 특성을 알아보았다 일반적으로 MODIS 위성자료를 이용한 적설연구는 근적외 채널을 활용한 NOSI (Normalized Difference of Snow Index)를 주로 사용한다. 하지만 본 연구는 정지기상 위성의 적셜 탐지 능력을 시험하기 위한 연구이다. 따라서 정지 기상 위성 탑재되어 있는 채널의 특성과 비슷한MODIS 가시 채널과 단파 적외 채널 자료를 이용하여 적설지역을 분석하였다단일 가시 채널을 이용하여 적설을 탐지 하는 것은 청천역일 경우 큰 어려움이 없으나 반면 구름과 적설이 혼재되어 있는 지역에서는 탐지 능력이 떨어진다.반면 BID 값을 활용한 적설지역 탐지는 단일 가시 채널을 활용한 방법보다 좋은 결과를 가지지만 하층운이 존재할 때는 여전히 적설과 구름을 명확히 구분하기는 어렵다.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.458-460
• /
• 2004

최근의 전력계통의 대형화와 고용량화로 인하여, 전력계통의 안정적으로 운용에 대한 기대가 절실히 요구되고 있다. 이처럼 계통은 안정적으로 운용하기 위하여 계퉁운용상에 발생하는 사고 및 과도상태를 신속, 정확하게 분석하고 판단함으로서 사고구간을 제거하고 피해구간을 최소화 할 수 있는 보호계전 협조와 실제 계통상에서 발생할 수 있는 다양한 사고를 분석하고 진단할 수 있는 향상된 보호계전 알고리즘 개발을 위한 연구가 필요하다. 따라서, 개발 혹은 개선된 보호계전 알고리즘의 평가를 위하여 다양한 사고 모의가 필요하며, 아울러 이를 기계장치 혹은 보호계전기 하드웨어를 시험할 수 있는 시뮬레이터 장치의 구성이 선행되어야 한다. 본 논문에서는 전력계통 과도현상 모의 프로그램인 PSCAD/EMTDC를 이용하여 다양한 계통 사고 모의하며, 결과 사고 데이터를 활용하여 보호계전 알고리즘을 평가하고자 한다. 한괸, 모의한 사고 데이터를 실시간으로 재현하기 위하여 고성능 DAC 인터페이스 장치를 활용하여 구현하고 다양한 사고 데이터를 데이터베이스 형식의 자료 구조로 구성하여, 대상 계전기 장치의 성능과 알고리즘을 검증하기 위한 시뮬레이터를 제안하고자 한다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.6
• /
• pp.1431-1440
• /
• 1993

This paper presents a new NC machine performance test and calibration system. In order to measure NC machine erros in simpler, and less time-comsuming way, some indirect measuring systems such as circular disk system and double ball bar system have been developed instead of laser interferometer. But these indirect measuring systems have shown their limits in identifying each of NC machine error sources in absolute numerical value. Therefore, we developed an unique NC machine error measurement system which provides a simple measuring process like other conventional indirect methods and still can indentify each of NC machine error sources in absolute numerical value.