• Geophysics and Geophysical Exploration
• /
• v.2 no.2
• /
• pp.86-95
• /
• 1999

This paper presents an efficient three-dimensional (3-D) modeling algorithm using the extended approximation to an electric field integral equation. Numerical evaluations of Green's tensor integral are performed in the spatial wavenumber domain. This approach makes it possible to reduce computing time, to handle smoothly varying conductivity model and to remove singularity problems encountered in the integration of Green's tensor at a source point. The responses obtained by 3-D modeling algorithm developed in this study are compared with those by the full integral equation for a thin-sheet EM scattering. The extensive analyses on the performance of modeling algorithm are made with the conductivity contrasts and source frequencies. These results show that the modeling algorithm are accurate up to the conductivity contrast of 1:16 and the frequency range of 100 Hz-100 kHz. The extended Born approximation, however, may produce inaccurate results for some source and model configurations in which the electric field is discontinuous across the conductivity boundary. We performed the modeling of a composite model of which conductivity varies continuously and this shows the modeling algorithm developed in this study is efficient for 3-D EM modeling. For a cross-hole source-receiver configuration a composite model of which conductivity varies continuously can be successfully simulated using this algorithm.

• Korean Journal of Construction Engineering and Management
• /
• v.12 no.6
• /
• pp.14-21
• /
• 2011

A unit modular system is a construction method which installs on site by manufacturing 50%~90% of the whole process in the factory. This method can minimize the process in the site and maximize the operation, which will reduce the duration and improve the overall quality. The recent paradigm of construction is to be sustainable building. Modular system can be regarded as a sustainable building construction method because it can reduce the amount of construction waste by recycling partial or whole part of overdue building be torn down. A unit modular system is the answer to cope with the increasing market of small size housings. A unit modular system is the most appropriate option at this point. This research proposes the standard operation and construction process of modular system, which enable to optimal system. A case study of reconstructing small-size housing was introduced to support this proposal. Finished unit modular is the reasonable way. However, 80% of complication rate of the modular is the most rational when a defect occurrence during delivery is considered.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.3C
• /
• pp.247-254
• /
• 2008

H.264 provides a good coding efficiency compared with existing video coding standards, H.263, MPEG-4, based on the use of multiple reference frame for variable block size motion estimation, quarter-pixel motion estimation and compensation, $4{\times}4$ integer DCT, rate-distortion optimization, and etc. However, many modules used to increase its performance also require H.264 to have increased complexity so that fast algorithms are to be implemented as practical approach. In this paper, among many approaches, fast mode decision algorithm by skipping variable block size motion estimation and spatial-predictive coding, which occupies most encoder complexity, is proposed. This approach takes advantages of temporal and spatial properties of fast mode selection techniques. Experimental results demonstrate that the proposed approach can save encoding time up to 65% compared with the H.264 standard while maintaining the visual perspectives.

• Journal of the Korea Convergence Society
• /
• v.11 no.1
• /
• pp.1-7
• /
• 2020

Recently 5G technology is one of the technologies that has been receiving much positive responses from users as it is integrated with virtual technology. However, 5G's security issues have not been fully resolved and more security is soon required. In this paper, an approach technique is proposed as a probability-based hierarchy to provide personal privacy for 5G-based IoT users more safely. The proposed technique is aimed at not exposing the privacy of IoT users to third parties by using two random keys created personally by IoT users. In order to satisfy both safety and efficiency, the proposed technology divides the privacy of IoT users into two layers. In the first stage, IoT users will control access to intermediate media using anonymous keys generated by IoT users, and in the second stage, information of IoT users registered with servers will be darkened and replicated. The proposed technique has improved the accuracy of the privacy protection of IoT users as they assign weights to layered information after layering users' privacy information on a probabilistic basis.

• Applied Chemistry for Engineering
• /
• v.3 no.1
• /
• pp.88-99
• /
• 1992

For the development of semiconducting photoelectrode to be more stable and efficient in the process of photoelectrolysis of the water, pure titanium rods were oxidized by anodic oxidation, furance oxidation and flame oxidation and used as electrodes. The Indium islands were formed by electrodeposition of "In" thin film on $TiO_2$ and Ti by electrodeposition. Also $A1_2O_3$ and NiO islands were coated on Ti by the electron-beam evaporation technique. The maximum photoelectrochemical conversion efficiency(${\eta}$) was 0.98% for flame oxidized electrode($1200^{\circ}C$ for 2min in air). Anodically oxidized electrodes have photoelectrochemical conversion efficiency of 0.14%. Furnace oxidized electrode($800^{\circ}C$ for 10min in air) has 0.57% of photoelectrochemical efficiency and shows a band-gap energy of about 2.9eV. The $In_2O_3$ coated $TiO_2$ exhibits 0.8% of photoelectrochemical efficiency but much higher value of ${\eta}$ was obtained with the Increase of applied blas voltage. However, $Al_2O_3$ or NiO coated $TiO_2$ shows much low value of ${\eta}$. The efficiency was dependent on the presence of the metallic interstitial compound $TiO_{0+x}$(x<0.33) at the metal-semiconductor interface and the thickness of the suboxide layer and the external rutile scale.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.5
• /
• pp.40-49
• /
• 2008

A Frequency synthesizer for mobile-DTV applications is implemented using $0.18{\mu}m$ CMOS process with 1.8V supply. PMOS transistors are chosen for VCO core to reduce phase noise. The measurement result of VCO frequency range is 800MHz-1.67GHz using switchable inductors, capacitors and varactors. We use varactor bias technique for the improvement of VCO gain linearity, and the number of varactor biasing are minimized as two. VCO gain deterioration is also improved by using the varactor switching technique. The VCO gain and interval of VCO gain are maintained as low and improved using the VCO frequency calibration block. The sigma-delta modulator for fractional divider is designed by the co-simualtion method for accuracy and efficiency improvement. The VCO, PFD, CP and LF are verified by Cadence Spectre, and the sigma-delta modulator is simulated using Matlab Simulink, ModelSim and HSPICE. The power consumption of the frequency synthesizer is 18mW, and the VCO has 52.1% tuning range according to the VCO maximum output frequency. The VCO phase noise is lower than -100dBc/Hz at 1MHz at 1MHz offset for 1GHz, 1.5GHz, and 2GHz output frequencies.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.04b
• /
• pp.49-49
• /
• 2009

최근 범세계적인 그린에너지 정책에 관련해 화석연료를 대체할 수 있는 수소, 풍력, 태양광 등의 대체 에너지에 대한 관심이 고조되고 있다. 이러한 여러 대체에너지 중에서도 태양광을 전기에너지로 변환하는 태양전지에 관한 연구가 집중되고 있다. 태양전지는 구조적으로 단순하고 제조 공정도 비교적 간단하지만, 보다 널리 보급되기 위해서는 경제성 향상이라는 문제점을 해결해야 한다. 이를 위해서는 기존의 실리콘 태양전지를 대체할 수 있는 신물질에 대한 연구가 필요하며, 그 중에서도 반도체 기술을 이용한 박막형 태양전지는 기존의 실리콘 태양 전지가 가지고 있는 고비용이라는 문제점을 극복할 수 있을 것으로 기대를 모으고 있다. 박막형 태양전지의 박막 재료로는 CIGS, CdTe 등이 연구되어지고 있지만, 아직까지는 기존의 실리콘 태양전지에 비해 에너지변환효율이 낮은 이유로 인해 실용화가 많이 이루어지지 못하고 있는 것이 사실이다. 이러한 박막형 태양전지의 재료들 중에서도 CdTe는 이종접합 박막형 태양전지에 흡광층으로 사용되는 것으로 상온에서 1.45eV 정도의 밴드갭(band gap) 에너지를 갖는 II-VI족 화합물반도체로써 태양광 스펙트럼과 잘 맞는 이상적인 밴드랩 에너지와 높은 광흡수도 때문에 박막형 태양전지로 가장 주목을 받고 있다. CdTe 박막의 제조 방법으로는 진공증착법(vacuum evaporation), 전착법(electrodeposition), 스퍼터링법(sputtering) 등이 있지만 본 연구에서는 스퍼터링법을 이용하여 박막을 증착하였다. 이상과 같이 증착된 CdTe 박막을 화학적기계적연마(CMP, chemical mechanical polishing) 공정을 적용시킴으로써, 태양전지의 에너지변환효율에 직접적인 영향을 끼칠 수 있는 CdTe 박막의 물리적, 전기적 특성들의 변화를 연구하기 위한 선행 연구를 진행하였다. 특히 본 연구에서는 CdTe 박막의 화학적 기계적 연마 특성을 분석하여 정규화를 통한 모델링을 수행하였다. 또한 화학적기계적연마 공정 전과 후의 표면 특성을 관찰하기 위해 SEM(scanning electron microscopy)과 AFM(atomic forced microscope)를 이용하였으며, 구조적 특성 관찰을 XRD(X-ray diffraction)를 사용하여 실험을 수행하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.3
• /
• pp.573-586
• /
• 2016

In construction jobs, a combination of various kinds of machinery is used to perform earthworks at a large-scale site. Individual equipments essentially cooperate with each other on task such as excavation, load, transfer and compaction. While other area have studied cooperation system, related study in domestic construction is in poor condition. In this study, construction equipment fleet management system is developed for solving this problem and find way to improving efficiency in earthworks site. The entire concept of the fleet management system, including its components and process, has been systematically outlined in this paper. An operational methodology has also been suggested, where a number of machines, such as the excavators, trucks and compactors, are chosen and further grouped into a cluster. A case study verify fleet management system's effectiveness on performing task package by comparing existing work method with methodology in this study. Fleet management system in this study is expected to curtail fuel consumption by the reduction of working time and moving distance. Furthermore, it can be anticipated to declining carbon emission effect.

• The Journal of the Korea Contents Association
• /
• v.16 no.7
• /
• pp.689-699
• /
• 2016

As the demand for LCD increases, the importance of inspection equipment for improving the efficiency of LCD production is continuously emphasized. The pattern inspection apparatus is one that detects minute defects of pattern quickly using optical equipment such as line scan camera. This pattern inspection apparatus makes a decision on whether a pixel is a defect or not using a single threshold value in order to meet constraint of real time inspection. However, a method that uses an adaptive thresholding scheme with different threshold values according to characteristics of each region in a pattern can greatly improve the performance of defect detection. To apply this adaptive thresholding scheme it has to be known that a certain pixel to be inspected belongs to which region. Therefore, this paper proposes a region matching algorithm that recognizes the region of each pixel to be inspected. The proposed algorithm is based on the pattern matching scheme with the consideration of real time constraint of machine vision and implemented through GPGPU in order to be applied to a practical system. Simulation results show that the proposed method not only satisfies the requirement for processing time of practical system but also improves the performance of defect detection.

• Journal of Navigation and Port Research
• /
• v.33 no.10
• /
• pp.723-734
• /
• 2009

Container Vessel is becoming larger and faster thanks to the rapid growth of global trade and development of technology. Therefore, 15,000TEU vessel is expected to be ordered in near future. Every nations in north-east Asia are facing strong competition to be logistics hub to get the initiatives of logistics in response to the rapid change of logistics environment. According to the globalization of economy and major ports in this region also are trying to catch big shipping line for their survival. Considering above circumstances of the advent of ultra-large container vessel and spoke-and-hub strategy, it is inevitably necessary to make a fast and accurate vessel job in the terminal in order to be a leading port To meet this objective, current vessel planning system has to be improved innovatively. Therefore, this thesis propose multi distributed vessel planning system which enables multi loading/discharging planning with several planner simultaneously for faster and more accurate than existing planning and enhances quality of planning through information sharing among planners. Also this thesis uses simulation through Arena to verify the efficiency of this multi-distributed vessel planning system.