• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.11
• /
• pp.1291-1297
• /
• 2014

This paper proposes integrated chassis control (ICC) with electronic stability control (ESC) and active rear steering (ARS). Direct yaw moment control is used to generate a control yaw moment. A weighted pseudo-inverse-based control allocation (WPCA) method is adopted to distribute the control yaw moment into tire forces, generated by ESC and ARS. Simulation-based tuning of variables weights in the WPCA is used to enhance the yaw moment distribution performance. Simulations using the vehicle simulation software $CarSim^{(R)}$ show that the proposed ICC is effective in improving maneuverability and lateral stability.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.6
• /
• pp.126-131
• /
• 2012

Tire force is one of important parameters which determine vehicle dynamics. However, it is hard to measure tire force directly through sensors. Not only the sensor is expensive but also installation of sensors on harsh environments is difficult. Therefore, estimation algorithms based on vehicle dynamic models are introduced to estimate the tire forces indirectly. In this paper, an estimation system for estimating lateral force and states is suggested. The state-space equation is constructed based on the 3-DOF bicycle model. Extended Kalman Filter, Unscented Kalman Filter and Ensemble Kalman Filter are used for estimating states on the nonlinear system. Performance of each algorithm is evaluated in terms of RMSE (Root Mean Square Error) and maximum error.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.4
• /
• pp.38-46
• /
• 2011

This paper presents roll angle estimator which used Kalman filter. Recently, the uses of the ELSD (Electronic Limited Slip Differential) and TVD(Torque Vectoring Differential) for vehicle yaw control are studied in many researches. However the roll angle can be negative effect of ELSD and TVD control. Therefore the information of roll angle can be used for vehicle yaw control. Moreover it can be used for rollover prevent control. Recently, most of the vehicles use lateral acceleration and yaw rate sensor. In this paper, design of Kalman filter which used lateral acceleration and yaw rate information is developed. In this paper, in order to verify the estimator ability, the CarSim and Matlab/Simulink are used.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.120-127
• /
• 2007

This paper describes the development of a nonlinear observer for four wheel steer (4WS) vehicle. An observer is designed to estimate the vehicle variables difficult to measure directly. A brake yaw motion controller (BYMC), which uses a PID control method, is also proposed for controlling the brake pressure of the rear and inner wheels to enhance lateral stability. It induces the yaw rate to track the reference yaw rate, and it reduces a slip angle on a slippery road. The braking and steering performances of the anti-lock brake system (ABS) and BYMC are evaluated for various driving conditions, including straight, J-turn, and sinusoidal maneuvers. The simulation results show that developed ABS reduces the stopping distance and increases the longitudinal stability. The observer estimates velocity, slip angle, and yaw rate of 4WS vehicle very well. The results also reveal that the BYMC improves vehicle lateral stability and controllability when various steering inputs are applied.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.6
• /
• pp.59-67
• /
• 2014

A numerical model and a controller of Active Front wheel Steer (AFS) system are designed in this study. The AFS model consists of four sub models, and the AFS controller uses sliding mode control and PID control methods. To test this model and controller an Integrated Dynamics Control with Steering (IDCS) system is also designed. The IDCS system integrates an AFS system and an ARS (Active Rear wheel Steering) system. The AFS controller and IDCS controller are compared under several driving and road conditions. An 8 degree of freedom vehicle model is also employed to test the controllers. The results show that the model of AFS system shows good kinematic steering assistance function. Steering ratio varies depends on vehicle velocity between 12 and 24. Kinematic stabilization function also shows good performance because yaw rate of AFS vehicle tracks the reference yaw rate. IDCS shows improved responses compared to AFS because body side slip angle is also reduced. This result also proves that AFS system shows satisfactory result when it is integrated with another chassis system. On a split-m road, two controllers forced the vehicle to proceed straight ahead.

• Journal of Korea Water Resources Association
• /
• v.32 no.1
• /
• pp.83-94
• /
• 1999

In continental margins, turbid underflows which are not confined to a given channel, are free to spread laterally as well as longitudinally. Lateral spreading can reduce substantially the run out distance of flows along continental shelves and slopes. Laboratory experiments with a large tank, employing saline density currents as surrogates for fine-grained turbidity flow, coupled with dimensional analysis, have been used to develop a simple expression for lateral spreading rates of two-dimensional flows on sloping beds. characteristic length and time are determined by the flow discharge and buoyancy flux at the inlet. By knowing the initial width of the flow, the spreading law can be used to estimate the maximum width of the current at different times as well as the longitudinal spreading rate. Predictions for flows compare favorably against observations.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.555-559
• /
• 2009

난류응력은 순간속도성분을 시간평균성분과 편차성분의 합으로 보고 Navier-Stokes 방정식으로부터 Reynolds 방정식을 유도할 때 나타나게 된다. Reynolds 방정식으로부터 수심 적분된 천수방정식을 유도하는 과정에서 시간 평균된 유속성분을 수심 적분된 유속성분과 편차성분의 합으로 본다면, 분산응력 (dispersion stress)이라고 하는 추가적인 새로운 항이 잔류하게 된다. 점성응력, 난류응력, 그리고 분산응력을 통칭하여 유효응력 (effective stress)이라고 한다. 일반적으로 수심에 비해 수로 폭이 넓은 개수로에서는 유효응력이 흐름특성의 수치 근사해에 큰 영향을 미치지 못한다고 가정하여 2차원 수심적분 모형에서 유효응력을 생략하기도 한다. 또한 유효응력을 적용하더라도, 점성응력이 난류응력에 비해 무시할 만큼 작다고 가정하여 난류응력만을 적용하며, 분산응력은 무시된다. 하지만 만곡부에서는 원심력과 편수위로 인한 횡방향 압력의 불균형이 발생하기 때문에, 만곡부의 이차류가 발생되며, 유속의 연직방향 분포도 일정하지 않게 된다. 따라서 본 연구의 목적은 만곡부의 이차류 특성을 수심적분 2차원 모형에 반영하기 위해 분산응력을 고려한 모형의 개발 및 검증이다. 불규칙한 모의영역을 원활히 나타낼 수 있도록 곡선좌표계를 사용하는 여타 모형들과 달리 유한유소법을 이용하여 수치해를 구하며, 따라서 x, y 좌표축을 사용하는 데카르트 좌표계를 사용하여 지배방정식을 나타낸다. 분산응력의 유 무에 따른 수치결과를 Rozovskii의 $180^{\circ}$ 만곡수로 실내실험 자료와 비교하여 개발 모형을 검증한다.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.6
• /
• pp.727-736
• /
• 2000

The present study investigates the influences of vehicle induced loads on the thermal buckling behavior of straight and curved continuous welded rail (CWR) tracks. Quasi-static loads model is assumed to determine the uplift region, which occurs due to the vertical track deflection induced by wheel loads of vehicle. The lateral loads of vehicle induced by weight, the speed, the superelevation and curvature of track, and other dynamic vehicle track interaction, are included in the ratio of lateral to vertical vehicle load. Parametric numerical analyses are perfomed to calculate the upper and lower critical buckling temperatures of CWR tracks, and the comparison between the results of this work and the previous results without vehicle is also included.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.6
• /
• pp.51-59
• /
• 2004

The evaluation of shear modulus is very important in various fields of civil engineering. In this paper, the site characterization method using HWAW method is applied to determine shear wave velocity profile of two test sites in order to verify the field applicability of HWAW method. Shear wave velocity profiles by HWAW method are compared with shear wave velocity profiles by SASW test and PS-Suspension Logging test. Through field applications, it is shown that HWAW method can minimize the effect of noise and lateral non-homogeneity of the site and determine detailed local shear wave velocity profile of site.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.12
• /
• pp.1596-1607
• /
• 2000

The optimal design of auto-catalyst needs a good compromise between the pressure drop and flow uniformity in the substrate. One of the effective methods to achieve this goal is to use the concept of radially variable cell density. But this method has not been examined its usefulness in terms of chemical behavior and conversion performance. In this work, two-dimensional performance prediction of catalyst coupled with turbulent reacting flow simulation has been used to evaluated the benefits of this method n the flow uniformity and conversion efficiency. The results showed that two cell combination of 93cpsc and 62 cpsc was the most effective for improved pressure drop and conversion efficiency due to balanced space velocity and efficient usage of geometric surface area of channels. It was also found that large temperature difference between the bricks in case that the edge of the frontal face of brick has too much lower cell density(less than 67% of cell density of the center of the brick). This study has also demonstrated that the present computational results show the better prediction accuracy in terms of CO, HC and NO conversion efficiencies compared to those of conventional 1-D adiabatic model by comparison with experimental results.