• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04b
• /
• pp.157-163
• /
• 1995

This paper presents an algorithm to deternine the tool path height for rough machining of sculptured surface. To minimize rough machining of sculptured surface, it is necessary to determine the tool path heights of contour planes. the proposed algorithm searches for the height at which maximum metal removal rate is obtained. This bisection method is accomplished until all shoulder heights are within roughing tolerance. The machining experiment demonstrates the superiority of the algorithm presented in this thesis.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.15-19
• /
• 1996

The cusp height in ball end milling, flat end milling and filleted end milling according to various surface inclination angle was calculated. The calculation result shows that, for each kind of tools, there exists certain range of inclination angle in which cusp height characteristics favorable. From machining time calculation, filleted end mill found to be superior to flat end mill in rough machining of sculptured surface.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.261-261
• /
• 2004

본 논문에서는 고속가공 시 필랫(코너-R) 엔드밀의 곡면가공 적용가능 여부를 연구하기 위하여 비교적 곡률이 완만한 곡면을 채택하여 가공실험을 수행하고 고 결과를 분석하였다. 가공재료는 금형의 재료로 많이 사용되는 SKD11 강을 선택하였다. 볼엔드밀과 필렛엔드밀의 비교를 위하여 2 종류의 공구에 동일한 가공조건으로 가공실험 하였다. 가공 중 측정된 절삭력과 가공면의 표면조도를 분석하여 일반적으로 황삭에서 주로 사용되던 필렛엔드밀을 곡률이 완만한 곡면의 정삭에 적용하였을 경우의 절삭특성과 볼엔드밀의 가공특성을 비교하였다.(중략)

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.11
• /
• pp.1917-1924
• /
• 2003

This paper proposes a roughing path generation method fer machining impeller with 5-axis machining center. Traditional researches are focus on finishing for machining impeller. To achieve efficient machining, roughing method must be studied. The proposed method consists two steps : One is to select optimal tool size and tool attitude by dividing cutting area into two regions to reduce cutting time. The regions are automatically divided by character point on the geometry of impeller blade. After dividing, the tool of the optimal size is selected for each divided region. The other is avoidance of tool interference. Tool interference in cutting areas is avoided by checking the distance between tool axis vector and ruling line on blade surface or approximated plan between ruling line. Using this method, the cutting time is reduced efficiently.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.568-571
• /
• 2004

This paper presents an efficient 5-axis roughing method for centrifugal impeller. The efficient roughing is minimization of cutting time through minimizing tool tilting & rotating motions. Roughing tool path plan consists of the three steps. First, machining areas are divided into sub cutting regions using ruling lines. The biggest tool diameter is, then, determined for each region. Finally, tool paths are generated after fixing the tilting and rotating axis of 5-axis machine. Experimental results showed that the proposed roughing plan considering the divided machining regions is more efficient than the conventional methods.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.398-401
• /
• 2001

This paper presents rough cutting pat고 drilling. This method has differences from conventional method which uses boundary curve by intersecting object to machine and each cutting plane. Die-cavity shape is drilled in z-map, we select various tool and remove much material in the short time. as a result, this method raise productivity. The major challenges in die-cavity pocketing include : 1)finding an inscribed circle for removing material of unmachined regions, 2) selecting optimal tool and efficiently arranging tool, 3) generating offset surface of shape, 4) determining machined width according to the selected tool, 5) detecting and removing unmachined regions, and 6) linking PJE(path-joining element). Conventional machining method calling contour-map is compared with drilling method using Z-map, for finding efficiency in the view of productivity.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.5
• /
• pp.110-119
• /
• 1998

Dynamic cutting force variations in milling process were measured indirectly using spindle motor current. Magnitude of the spindle motor current is independent of cutting direction. Quasi-static sensitivity of the spindle motor current is higher than that of the feed motor current. Dynamic sensitivity of the spindle motor current is lower but cutting force was correctly represented by spindle RMS current in rough milling. In rough milling, chipping and tool fracture were well detected by the proposed tool fracture index using spindle motor current.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.7 s.196
• /
• pp.60-68
• /
• 2007

This paper presents an efficient 5-axis roughing method for centrifugal impeller. The efficient roughing is minimization of cutting time through minimizing tool tilting and rotating motions. To minimized cutting time, machining area is divided into sub-cutting regions using control points on hub curves and shroud curves of blade used to design and analyze centrifugal impeller. For sub-cutting regions, diameters of cutting tools are determined as big as possible. Then, tool paths are generated with the tilting axis and rotating axis of 5-axis machine limited and fixed, which can give more efficient machining speed and machining stability than the conventional methods. Experimental results show that the proposed method is more efficient than the conventional methods to mill with the only one cutting tool without dividing area and the previous methods to mill with simultaneous 5-axis processing with dividing area.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04b
• /
• pp.143-148
• /
• 1995

A study on the generation of optimum tool path for machining the concave parts is discussed. Above all, the various cutting factors and their relationships are considered. Then optimum tool path for concave parts is generated on these cutting variables and their relationships. It is difficult for existing CAD/CAM systems tomachine the concave parts. For cutting the part even the experienced craft must give many attentions and muchtime since it needs consideration of various cutting conditions and geometric properties. The optimum tool path for the concave part is generated onnot only geometric properties byut also cutting conditions. We choose, as variables, feed and cutting direction for productivity, diameter of tool and constant(stable) cutting force for machining accuracy. The results are verified through simulation of the index of performance and cutting force.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.1
• /
• pp.53-64
• /
• 1994

Rouge cutting process takes the major portion of machining operation using NC milling machine. Especially, most of the machining time is spent in this process when molds are machined. Therefore, an efficient algorithm for generating the tool path for rough cutting is suggested in this paper. The first step of the procedure is getting the volume to be machined by applying the Boolean operation on the finished model and the workpiece which have been modeling system. Basic principle of determining machining procedure is that a large tool should be used at the portion of the simple shape while a small tool should be used at the complex portion. This principle is realized by representing the volume to be machined by an octree, which is basically a set of hexahedrons, and matching the proper tools with the given octants. When the tools are matched with the octants, the tool path can be derived at the same time.