• Journal of the Korean Ceramic Society
• /
• v.39 no.3
• /
• pp.272-277
• /
• 2002

Aluminum nitride (AlN) powders and whiskers were synthesized by a modified carbothermal reduction and nitridation where a ($NH_4)[Al(ethylenediaminetetraacetate)]{\cdot}2H_2O$ complex is used as precursor. The AlN powders were obtained by calcining the complex without mixing any carbon source under a flow of nitrogen in the temperature range 1200∼1500$^{\circ}$C and then burning out the residual carbon. The nitridation process was investigated by $^{27}Al$ magic-angle spinning (MAS) unclear magnetic resonance, infrared spectroscopy and X-ray diffraction. The complex is pyrolyzed, converted to ${\rho}$- and ${\gamma}$- alumina and then nitridated to AlN without ${\gamma}-{\alpha}$ alumina transition. The morphology of ${\gamma}$-alumina, when it was converted to AlN, was retained, strongly indicating that ${\gamma}$-alumina is converted to AlN through solid-state $AlO_xN_y$, not through gaseous intermediates such as aluminum and aluminaum suboxides. AlN whiskers were obtained, when a (0001) sapphire was used as a catalyst.

• Journal of the Korean Vacuum Society
• /
• v.13 no.3
• /
• pp.120-126
• /
• 2004

A damage-reduced trench was investigated in view of the defect distribution along trench sidewall and bottom using high resolution transmission electron microscopy, which was formed by HBr plasma and additive gases in magnetically enhanced reactive ion etching system. Adding $O_2$ and other additive gases into HBr plasma makes it possible to eliminate sidewall undercut and lower surface roughness by forming the passivation layer of lateral etching. To reduce the RIE induced damage and obtain the fine shape trench corner rounding, we investigated the hydrogen annealing effect after trench formation. Silicon atomic migration on trench surfaces using high temperature hydrogen annealing was observed with atomic scale view. Migrated atoms on crystal surfaces formed specific crystal planes such as (111), (113) low index planes, instead of fully rounded comers to reduce the overall surface energy. We could observe the buildup of migrated atoms against the oxide mask, which originated from the surface migration of silicon atoms. Using this hydrogen annealing, more uniform thermal oxide could be grown on trench surfaces, suitable for the improvement of oxide breakdown.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.12 no.1
• /
• pp.36-41
• /
• 2002

Abstract The stoichiometric and double-ordered perovskite $Sr_2FeMoO_6$ (SFMO) polycrystalline ceramics were fabricated by sintering at above $900^{\circ}C$ in $H_2$(5%)/Ar reductive ambient. SMO polycrystals showed good ferromagnetic properties andmagnetrotesistqnce ratios of about 15 % at 8K and 3 % at room temperature. Amorphous SFMO thin films were deposited on $LaA1O_3$ and $SrTiO_3$ single crystal substrates using rf sputtering method with the SFMO polycrystalline ceramic target. Double-ordered perovskite polycrystalline SFMO thin films were fabricated by solid state crystallization by annealing the deposited amorphous films at above $680^{\circ}C$ in $H_2$(5%)/Ar reductive ambient. SFMO thin films exhibited ferromagnetic behavior. Their magnetroresistance ratios, however, were only 0.3~0.5% at 8K and disappeared with increasing the measuring temperature. This was attributed to the absence of magnetic spin tunneling between grains due to the porous structure and non-stoichiometric composition of the deposited films.

• Applied Chemistry for Engineering
• /
• v.16 no.5
• /
• pp.635-640
• /
• 2005

Mediated electrochemical oxidation (MEO) is an aqueous process which oxidizes organics electrochemicallly at low temperatures and pressures. The useful process can be used to treat mixed wastes containing hazardous organics. This paper have studied MEO of ethylene glycol (EG) in nitric acids by Fe(III)/Fe(II) and Co(III)/Co(II) system. It investigated current density, supporting electrolyte concentration, hydraulic retention time, removal efficiency of EG by MEO. Removal efficiency of EG by MEO was superior in Co(III)/Co(II) redox system than Fe(III)/Fe(II) redox system, where MEO removal efficiency was 100 percent. In case of EG, the reactions were fast and good yields of carbon dioxide formation was observed.

• The Journal of Natural Sciences
• /
• v.14 no.2
• /
• pp.41-54
• /
• 2004

$LaMnO_3$ and A site substituted $La_{0.9}Sr_{0.1}MnO_3$(a=$5.33\AA$, c=$13.27\AA$), B site substituted $LaMn_{0.9}Cu_{0.1}O_3$(a=$5.52\AA$, c=$13.31\AA$) mixed oxides were prepared by Citrate sol-gel method. The powder X-ray diffraction patterns of these oxides were indexed with single phase hexagonal perovskite structures. According to the TRR result, oxygen stoichiometry of these oxides were oxidative nonstoichiometry as like $LaMnO_{3.16}$, $La_{0.9}Sr_{0.1}MnO_{3.10}$ and $LaMn_{0.9}Cu_{0.1}O_{3.14}$ Reduction reactions of un-substituted $LaMnO_3$ was two steps, but specific site(A site of B site) partially substituted $LaMnO_3$ oxides were procees to three reactions.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.7
• /
• pp.884-891
• /
• 2016

A secondary injection system in a diesel engine has benefits: it can be controlled independently without interrupting engine control, it can be adapted to various layouts for exhaust systems, and it pose no reductant dilution problems compared to post injection systems in the combustion chamber or other supplemental reductant injections. In a secondary injection system, the efficiency of the catalyst depends on the method of reducing the supply. The reductant needs to be maintained and optimized with constant pressure, the positions and angles of injector is a very important factor. The concentration and amount of reductant can be changed by adjusting secondary injection conditions. However, secondary injection is highly dependent upon the type of injector, injection pressure, atomization, spray technology, etc. Therefore, it is necessary to establish injection conditions the spray characteristics must be well-understood, such as spray penetration, sauter mean diameter, spray angle, injection quantity, etc. Uniform distribution of the reductant corresponding to the maximum NOx reduction in the DeNOx catalyst system must also assured. With this goal in mind, the spray characteristics and impingement plate types of a secondary injector were analyzed using visualization and digital image processing techniques.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.5
• /
• pp.208-215
• /
• 2005

The 10mm diameter aggregates made of clay, carbon and $Fe_2O_3$ were prepared to investigate the mechanism of black core formation. The specific gravity, absorption rate, percent of black core area, fracture strength, total Fe analysis, and XRF were measured at various compositions, sintering temperatures, sintering times, sintering atmospheres, and sintering methods. Small addition of $Fe_2O_3$ did not affect physical properties of the aggregates; however, the percent of black core area increased with increasing carbon contents and increasing sintering temperature. Specific gravity of the aggregates decreased and the water absorption ratio increased with increasing percent of black core area. The aggregates sintered at oxidation atmosphere showed clear border between shell and black core area. Hence, the aggregates sintered at reduction atmosphere showed only black core area in the cross-section of the aggregates. The specific gravity of the aggregates sintered at reduction atmosphere increased with increasing carbon contents and that was the lowest of all comparing other aggregates sintered at different atmospheres. Adsorption rate increased with increasing carbon contents at all atmospheres. The fast sintered aggregates showed lower specific gravity, higher absorption rate, and more black core area than the normally sintered aggregates. It was turned out that the aggregates having more black core area showed higher fracture strength than that of aggregates with no black core area. From the total Fe analysis, the concentration of Fe and FeO was higher at black core area than at shell. Because the concentration of $Fe_2O_3$ in the shell was higher than other area, the color of the shell appeared red. It was also turned out from the XRF analysis that carbon was exist only at black core area.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1520-1522
• /
• 1999

저 전압용 형광체는 최근에 활발히 연구가 진행되고 있으며 가장 대표적인 형광체가 ZnO : Zn 녹색 형광체이다. ZnO : Zn 형광체는 자체발광형 형광체로써 ZnO을 환원분위기 하에서 열처리를 함으로써 얻을 수 있다. 본 연구에서는 자발착화 연소반응법(Glycine Nitrate Process)을 이용하여 ZnO : Zn 분말을 합성하고 형광특성 및 분말특성을 알아보았다. 출발물질로는 Zn Nitrate와 Glycine을 이용하였고 자발연소 반응이 발생하는데 적절한 글리신의 양을 확인하기 위해서 글리신과 양이온의 비를 변화시키며 ZnO를 합성하였다. 그리고 Zn Excess가 생겨난 양과 그에 따른 형광특성을 관찰하기 위해 $N_2$ 분위기에서 각기 $500^{\circ}C,\;750^{\circ}C,\;950^{\circ}C$의 온도에서 열처리를 행하였다. 제조된 ZnO 분말의 입자형태와 결정상태는 SEM과 XRD를 이용하여 분석하였고 TG-DTA를 측정하여 열처리 온도에 따른 질량감소(ZR excess)를 관찰하였다. 또 Particle size analyzer로 분말의 크기를 알아보았고 형광체로써의 발광특성을 살펴보기 위해 PL을 이용하여 발광피크를 관찰하였다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2013.05a
• /
• pp.174-174
• /
• 2013

현재 자동차 강판 시장에서는 승객들의 안전 확보와 연비 향상을 위하여 자동차 강판의 경량화 및 고장력화가 급속히 진행되고 있다. 더불어 소비자는 더욱 아름답고 멋있는 외관을 추구하면서 정교한 디자인이 가능할 수 있도록 높은 성형성을 갖는 강판에 대한 요구도 또한 증대되고 있다. 따라서 강도와 성형성을 동시에 확보할 수 있는 DP형, TRIP형 등의 다양한 컨셉을 갖는 변태강화형 고장력강에 대한 개발 요구가 점점 심화되고 있으나 이들 고장력강의 상 제어를 위하여 첨가된 Si, Mn등의 성분들이 표면에 안정한 산화물을 형성하기 때문에 이러한 고장력강은 표면 품질이 열위한 것으로 보고 되고 있다. 따라서 기존 연구에서는 열처리중 표면으로 확산되어 올라오는 Si, Mn 산화물의 저감을 위하여 분위기 중 산소농도나 노점등을 조절하거나, 산화전처리, 선도금처리 등을 통하여 Si, Mn 의 표면 선택산화를 제어하여 도금 결함을 최소화하려는 연구가 많이 진행되고 있다. 그러나 이러한 연구들은 대부분 강판 표면에서의 산화/환원의 반응에 대한 분위기 요인을 제어하는 연구들이며 실제 Si, Mn등의 산화성 원소들이 어떠한 조건에서 어떠한 경로들을 통해서 이동하여 표면으로 올라오는지에 대한 연구는 부족한 상황이다. 따라서 본 연구에서는 산화성 원소들의 표면 확산 거동에 대한 고찰을 위하여 다양한 열처리 온도 조건을 통한 표면 도금성 경향, 합급화 경향 및 표면 분석결과를 바탕으로 확산 거동에 대한 경향을 밝히고자 하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.378-382
• /
• 1999

저 전압용 형광체는 최근에 활발히 연구가 진행되고 있으며 가장 대표적인 형광체가 ZnO Zn 녹색 형광체이다. ZnO : Zn 형광체는 자체발광형 형광체로써 ZnO을 환원분위기 하에서 열처리를 함으로써 얻을 수 있다. 본 연구에서는 자발착화 연소반응법(Glycine Nitrate Process)을 이용하여 ZnO : Zn 분말을 합성하고 형광특성 및 분말특성을 알아보았다. 출발물질로는 Zn Nitrate와 Glycine을 이용하였고 자발연소 반웅이 발생하는데 적절한 글리신의 양을 확인하기 위해서 글리신과 양이온의 비를 변화시키며 ZnO를 합성하였다. 그리고 Zn Excess가 생겨난 앙과 그에 따른 형광특성을 관찰하기 위해 $N_2$ 분위기 에서 각기 50$0^{\circ}C$, 75$0^{\circ}C$, 95$0^{\circ}C$의 온도에서 열처리를 행하였다. 제조된 ZnO 분말의 입자형태와 결정상 태는 SEM과 XRD를 이용하여 분석하였고 TG-DTA를 측정하여 열처리온도에 따른 질량감소(Zn excess)를 관찰하였다. 또 Particle size analyzer로 분말의 크기를 알아보았고 형광체로써의 발광특성을 살펴보기 위해 PL을 이용하여 발광피크를 관찰하였다.