• Journal of Korea Society of Industrial Information Systems
• /
• v.27 no.6
• /
• pp.41-49
• /
• 2022

The Internet Engineering Task Force (IETF) has standardized RPL (IPv6 Routing Protocol for Low-power Lossy Network) as a routing protocol for Low Power and Lossy Networks (LLNs), a low power loss network environment. RPL creates a route through an Objective Function (OF) suitable for the service required by LLNs and builds a Destination Oriented Directed Acyclic Graph (DODAG). Existing studies check the residual energy of each node and select a parent with the highest residual energy to build a DODAG, but the energy exhaustion of the parent can not avoid the network disconnection of the children nodes. Therefore, this paper proposes EC-RPL (Enhanced Connectivity-RPL), in which ta node leaves DODAG in advance when the remaining energy of the node falls below the specified energy threshold. The proposed protocol is implemented in Contiki, an open-source IoT operating system, and its performance is evaluated in Cooja simulator, and the number of control messages is compared using Foren6. Experimental results show that EC-RPL has 6.9% lower latency and 5.8% fewer control messages than the existing RPL, and the packet delivery rate is 1.7% higher.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.49 no.4
• /
• pp.481-496
• /
• 2022

The purpose of this study was to compare factors causing stress in pediatric and general dentists when treating pediatric patients and to evaluate their overall occupational stress level. A total of 191 dentists participated in the online survey, consisting of 66 pediatric dentists and 125 general dentists. The questionnaire was conducted using Google Form. Both groups were stressed due to poor cooperation of patient and caregiver, uncertain prognosis of treatment, and low cost of pediatric dental treatment. The pediatric dentists felt relatively high stress due to poor cooperation from caregivers and an uncertain prognosis of treatment (p < 0.05). Overall occupational stress was high in both groups in the order of patient, time, job environment, and income-related stress, and the degrees of pediatric dentists were lower than general dentists. Among the 3 sub-factors of occupational burnout, more than 98% of both groups showed burnout in "depersonalization", and more than 69% of both groups showed burnout in "emotional exhaustion". Both groups showed a low burnout rate in "reduced sense of accomplishment" and pediatric dentists showed a higher sense of accomplishment than general dentists (p < 0.05). This study showed that both groups were under high occupational stress due to various factors, and efforts were required to relieve stress.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.64 no.6
• /
• pp.65-75
• /
• 2022

Livestock industry in Korea has been growing rapidly and has reached 23 trillion Korean won in 2021. This study focuses on broiler, which is one of the largest sectors in livestock industry. As the effects of climate change get more serious, primary industry such as livestock industry is fragile to climate change since it directly interacts with nature. Therefore, maintaining suitable rearing environment is important. One of the most frequently used ventilation type for controlling the rearing environment of broiler house, tunnel ventilation, causes frequent air velocity fluctuation which makes maintaining the rearing environment important. By measuring the air temperature, relative humidity and air velocity in various points inside the broiler house, the internal thermal environment uniformity was analyzed according to length, width and zone. The experimental house was found to have dead zone with high air temperature, relative humidity and low air velocity near the end of the inlet and at the end of the broiler house. By using heat stress index to analyze quantitatively, zone with highest heat stress index was found to increase by 7.55% compared to the lowest zone. As a result, to maintain uniform rearing environment inside the broiler house, different factors must be measured and analyzed and used to operate the environmental control facilities.

• Journal of The Korean Association of Information Education
• /
• v.26 no.3
• /
• pp.197-207
• /
• 2022

In this paper, we develop a machine learning based block code generation and recommendation model for the purpose of reducing cognitive load of learners during coding education that learns the learner's block that has been made in the block programming environment using natural processing model and fine-tuning and then generates and recommends the selectable blocks for the next step. To develop the model, the training dataset was produced by pre-processing 50 block codes that were on the popular block programming language web site 'Entry'. Also, after dividing the pre-processed blocks into training dataset, verification dataset and test dataset, we developed a model that generates block codes based on LSTM, Seq2Seq, and GPT-2 model. In the results of the performance evaluation of the developed model, GPT-2 showed a higher performance than the LSTM and Seq2Seq model in the BLEU and ROUGE scores which measure sentence similarity. The data results generated through the GPT-2 model, show that the performance was relatively similar in the BLEU and ROUGE scores except for the case where the number of blocks was 1 or 17.

• Journal of Internet Computing and Services
• /
• v.23 no.2
• /
• pp.29-35
• /
• 2022

UV rays have beneficial or harmful effects on the human body depending on the degree of exposure. An accurate UV information is required for proper exposure to UV rays per individual. The UV rays' information is provided by the Korea Meteorological Administration as one component of daily weather information in Korea. However, it does not provide an accurate UVI at the user's location based on the region's Ultraviolet index. Some operate measuring instrument to obtain an accurate UVI, but it would be costly and inconvenient. Studies which assumed the UVI through environmental factors such as solar radiation and amount of cloud have been introduced, but those studies also could not provide service to individual. Therefore, this paper proposes a deep learning model to calculate UVI using solar object information and sunlight characteristics to provide an accurate UVI at individual location. After selecting the factors, which were considered as highly correlated with UVI such as location and size and illuminance of sun and which were obtained through the analysis of sky images and solar characteristics data, a data set for DNN model was constructed. A DNN model that calculates the UVI was finally realized by entering the solar object information and sunlight characteristics extracted through Mask R-CNN. In consideration of the domestic UVI recommendation standards, it was possible to accurately calculate UVI within the range of MAE 0.26 compared to the standard equipment in the performance evaluation for days with UVI above and below 8.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.6
• /
• pp.54-63
• /
• 2022

This paper is a study on the friction damper, which is one of the seismic reinforcement devices for structures. This study developed a damper by replacing the internal friction material with ultra high molecular weight polyethylene (UHMWPE), a type of composite material. In addition, this study applied a multi-friction method in which the internal structure where frictional force is generated is laminated in several layers. To verify the performance of the developed multi-friction damper, this study performed a characteristic analysis test for the basic physical properties, wear characteristics, and disc springs of the material. As a result of the wear test, the mass reduction rate of UHMWPE was 0.003%, which showed the best performance among the friction materials based on composite materials. Regarding the disc spring, this study secured the design basic data from the finite element analysis and experimental test results. Moreover, to confirm the quality stability of the developed multi-friction damper, this study performed an seismic load test on the damping device and the friction force change according to the torque value. The quality performance test result showed a linear frictional force change according to the torque value adjustment. As a result of the seismic load test, the allowable error of the friction damper was less than 15%, which is the standard required by the design standards, so it satisfies the requirements for seismic reinforcement devices.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.6
• /
• pp.14-22
• /
• 2022

In this study, a fire test was conducted to evaluate the fire performance of precast concrete (PC) slabs in an outdoor environment in response to the increase in fire incidents caused by the growth of warehouses. Prior to the field fire test, the tensile yield strength of the tendon at elevated temperatures was tested to analyze the mechanical properties. Also, by referring to previous studies, the thermal properties of tendon and the mechanical and thermal properties of concrete were investigated. A field fire test was conducted to analyze the structural and fire performance of two identical slabs with 50 and 150 mm bearing length. As the bearing length increased, deflection and horizontal displacement decreased. The fire test lasted for 200 minutes without the collapse of slabs, validating current codes. Based on the structural performance which maintained even with concrete spalling and rupture of some tendons, the bonded method is assumed to be practical in pre-tensioned PC slabs. The results of fire test are expected to be utilized in evaluating the fire performance of PC slabs in warehouses.

• Journal of Practical Engineering Education
• /
• v.14 no.1
• /
• pp.205-217
• /
• 2022

For high school students in Jeonbuk, this study aims to identify the problems caused by outflow of local youth population and their preference factors to enter university in Seoul-metropolitan area, and to draw out the direction of local human resources program, through questionnaire investigation and focused group interview. The main findings are as follows: First, 68.8% of high school students, especially the top grade students prefer to enter university in metropolitan area. The metropolitan cultural characteristics, such as reputation of universities and ranking, openness and anonymity, and urban infrastructure attract students. Second, there is a close relationship between the individual background, growth area - enrollment area - employment area, and the location dependency without return migration is very strong. Third, local human resources program was evaluated as a meaningful activity for high school students, in order to understand the further education and career, and have an interest in local universities. Therefore, it is necessary to discover industries consistent with local identity, create networks, develop and implement programs considering the actual educational conditions. The gender-free program, supplement program for the integrated curriculum, and contents that to supplement science subjects should be developed. Additionally, this issue could be resolved expanding the perspective of balanced national development and improve the local environment to enhance the urban attraction points.

• Journal of the Korean Society of Safety
• /
• v.37 no.4
• /
• pp.120-128
• /
• 2022

Printed circuit boards (PCBs) are a basic component in the electronics industry and are widely used in nearly all electronic products, such as mobile phones, tablet computers, and digital cameras, as well as in electric equipment. PCB manufacturing involves the use of many chemicals and chemical processes and therefore has more risks than other manufacturing sectors. This study aims to identify the causes of possible accidents during PCB manufacturing through risk assessment, develop and implement safety measures, and evaluate the effectiveness of these measures. Note that the safety measures developed to mitigate the risks of a certain process were also implemented for other similar processes. The risk assessments conducted over seven years, from 2015 to 2021, at a PCB manufacturing company identified 361 hazardous processes. Between 2016 and 2019, 41-56 hazardous processes were identified per year; such processes decreased to fewer than 20 per year after 2020. Application of the risk assessment results to the improvement of the hazardous processes with the similar characteristics seems to be effective in decreasing the risks. Equipment-related factors such as lack of appropriate maintenance, low work standards, and defective protection devices were responsible for 59.8% of all possible accidents. Because PCB manufacturing involves many chemicals, skin contact with hazardous substances, electric shock, fire, and explosion were the most common types of possible accidents (81.7%). In total, 505 safety measures were implemented, including 157 related to purchase and improvement of equipment and devices for safety (31.1%), 147 related to the installation/modification of fire prevention facilities (29.1%), and 69 related to the use of standard electrical appliances (13.7%). Risk assessment conducted after implementing the safety measures showed that these measures significantly decreased risk; 247 processes (68.4%) had a risk level of 3, corresponding to "very low," and 114 processes (31.6%) showed a risk level of 4, corresponding to "low." In particular, risk assessment of 104 processes with risk scores of 12 and 10 other processes with risk score of 16 showed that the risk decreased to 4 after implementing the safety measures. Thus, implementing these measures in similar manufacturing sectors that involve chemical processes can mitigate risk.

• The Journal of the Convergence on Culture Technology
• /
• v.8 no.6
• /
• pp.703-708
• /
• 2022

Tables and figures in academic literature contain important and valuable information. Tables and figures represent the essence of the refined study, which is the closest to the raw dataset. If so, can researchers easily access and utilize these image data through the search system? In this study, we try to identify user perceptions and needs for image data through user and case studies. Through this study we also explore expected effects and utilizations of image search systems. It was found that the majority of researchers prefer a system that combines table and figure indexing functions with traditional search functions. They valued the provision of an advanced search function that would allow them to limit their searches to specific object types (pictures and tables). Overall, researchers discovered many potential uses of the system for indexing tables and figures. It has been shown to be helpful in finding special types of information for teaching, presentation, research and learning. It should be also noticed that the usefulness of these systems is highest when features are integrated into existing systems, seamlessly link to fulltexts, and include high-quality images with full captions. Expected effects and utilizations for user-centered image search systems are also discussed.