• Korean Chemical Engineering Research
• /
• v.55 no.5
• /
• pp.690-697
• /
• 2017

In this study, styrene-isoprene-styrene (SIS)-styrene-butadiene-styrene (SBS) modified asphalt was prepared for waterproof-sheet to measure its properties including softening point, penetration, low temperature flexibility, viscosity and adhesion. Then the properties of SIS-SBS modified asphalt imparted with self-healing were optimized to seek for optimal compositions of SIS and SBS versus asphalt according to response surface methodology (RSM). As the content of SBS or SIS was increased, both properties of softening point and viscosity, measured at high temperature, were increased with a statistical significance. However, the increments of softening point and viscosity per unit content of SBS added, were observed to be greater than those per unit content of SIS added, respectively. It was due to the difference of thermal properties of SBS and SIS at high temperature that the cross-linking degree of SBS was increased by gelation accompanied with the increase of viscosity, while chain-entanglement of SIS was relatively reduced owing to a chain scission of poly(isoprene) blocks causing the decrease of viscosity. To the contrary, SIS-SBS modified asphalt showed a behavior of the least elasticity resulting in both the maximum of penetration and adhesion, measured at room temperature, as well as the lowest low temperature flexibility at the composition of SIS, 4 g and SBS, 8.5 g based on asphalt, 63 g.

• Korean Journal of Food Science and Technology
• /
• v.9 no.4
• /
• pp.284-290
• /
• 1977

The lipid components, fatty acid compositions, physical and chemical characteristics of crude oil in Amorpha fruticosa seed were determined and proximate compositions of it were also analyzed. The results were summarized as follow: 1) The proximate composition showed moistrue to be 10.14%, crude protein to be 21.77%, crude fats to be 12.73%, carbohydrates to be 51.75% and crude ash to be 3.61%. 2) Specific gravity, refractive index, smoke point and titer of the crude oil were $0.925\;(15/15^{\circ}C)$, $1,477(15^{\circ}C)$, $175^{\circ}C$ and $14.8^{\circ}C$, respectively. 3) Iodine, saponification, acid, ester value and unsaponifiable content of the crude oil were 144, 182, 2.9, 179 and 5.17%, respectively. 4) Lipid components were separated by TLC and quantitatively determined by TLC scanner to give 75% triglycerides, 14% esterified sterols, 3.08% phospholipids, 4.4% free sterols and 3.77% free fatty acids. 5) Fatty acid compositions were quantitatively determined by GLC to give 76.21% linoleic acid, 9.92% palmitic acid, and 5.07% stearic acid as the main components, oleic, linolenic, palmitoleic and arachidic acid were presented in small quantities.

• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.5
• /
• pp.288-302
• /
• 2017

Accurate measurement of benthic nutrient fluxes (BNF) is a prerequisite for evaluating the effect of sediments on nutrient cycle in the surface water. The intact sediment cores were collected in July 2015 at the midstream of Nakdong River. We identified pre-incubation time (6, 12, 24 hr), dissolved oxygen concentration (90, 70, 50% saturation), diffusive boundary layer thickness (0, 0.6-0.8, 1.2-1.4 mm), and incubation temperature (10, 17, 20, $25^{\circ}C$) as the most important control factors, and measured the BNF fluctuation with the variation of these factors using the laboratory sediment core incubation method. Since the chemical composition, redox condition, hydrodynamic regimes and microbial activities at the sediment-water interface were changed as a result of the alteration of control factors, sediment core incubation should be conducted under as close to the natural conditions of study site as possible, in order to produce the results similar to actual values. Relative percentage differences between two replicates were below 20% in most control factors, which showed satisfactory precision for strict compliance with the experimental conditions and procedures. In the further studies, we will compare the results of core incubation with those of in situ measurements to confirm the accuracy of the sediment core incubation method.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.8 no.4
• /
• pp.100-110
• /
• 2000

Studies were conducted to know effects of the bulking agents (saw dusts, mushroom waste, wheat bran coconut meal, rice hulls) adding o moisture control, fermentation methods (aerobic and anaerobic) and periods (1 to 20 days) of food waste fermentation for animal feeds on chemical compositions and in vitro DDM (digestibility of dry matter). Experiment designs were focussed basically to obtain extension service data. The NDF (neutral detergent fiber) composition in the oak and pine saw dust were 93.5% and 95.4% (DM basis) in respectively. Thus, the fermented food waste feeds using saw dust (50%) increased NDF(12%), and decreased in vitro DDM(48%) compared to those of raw materials before aerobic fermentation. The oak saw dust showed higher DDM compared to pine. Mushroom wastes which is a residues of mushroom culture mixed originally willow saw dust (80%) and wheat bran (20%) showed quite higher feed value compared to both saw dusts. It was found that an in vitro DDM and NDF composition in fermented feeds appeared highly dependent or the NDF composition in bulking agents. With an increase wheat bran ratio substitute mushroom waste showed linearly decreased NDF, and increased in vitro DDM in the fermented food waste feeds. The fermented feeds added bottling agents composed higher NDF resulted in higher NDF and lower in vitro DDM with prolonged fermentation time. The feeds from anaerobic fermentation appeared lower NDF and higher in vitro DDM compared to those of aerobic fermentation.

• Korean Chemical Engineering Research
• /
• v.49 no.6
• /
• pp.829-834
• /
• 2011

Lysozyme in egg white functions as bacteriolysis agent and ovalbumin plays a role as antigen in immune system. Egg white analysis methods usually include electrophoresis, gel permeation chromatography and reversed-phase HPLC(RP-HPLC). Among them, RP-HPLC was selected for rapid analysis and C18 column(Agilent, USA) was used as HPLC column. Optimum conditions were searched by changing mobile phase and temperature. Capacity factor and resolution were calculated and compared for various elution conditions. In the isocratic elution, mobile phase volume ratio was changed from 30/70/0.1 to 60/40/0.1(Acetonitrile(ACN)/Distilled water(DW)/Trifluoroacetic acid(TFA)). ACN composition was increased by 10% and temperature was set as $20^{\circ}C$. In the gradient elution, ACN/DW ratio was changed from 10/90 to 60/40 during 20 minute and temperature was varied as 20, 30 and $40^{\circ}C$. In the isocratic elution, three peaks were separated at 50/50/0.1. Lysozyme and ovalbumin were confirmed as first and third peak in three peaks respectively. In the gradient elution, four peaks were separated at $30^{\circ}C$. Lysozyme and ovalbumin were confirmed as first peak and third peak in four peaks respectively.

• Korean Chemical Engineering Research
• /
• v.43 no.2
• /
• pp.236-242
• /
• 2005

Membrane fouling by protein mixtures during microfiltration has been investigated for binary mixtures of bovine serum albumin (BSA), casein, lysozyme, pepsin, and ovalbumin. Filtration experiments were carried out using $0.2{\mu}m$ polycarbonate track-etched (PCTE) membrane in a stirred cell under constant transmembrane pressure (14 kPa) and concentration of hydrogen ion (pH=11) to study the effect of mixture composition on filtrate flux decline. Flux decline data were analyzed using a pore blockage-cake formation model developed recently. It was found that the model is in a good agreement with the experimental data. Fouling parameters such as the rate of pore blockage(${\alpha}$), the initial resistance of the protein deposit ($R_{po}$) and the increasing rate of the protein layer resistance(${\beta}$) were used to evaluate the rate of filtrate flow by membrane fouling in the binary mixture system. Generally, the trend of ${\alpha}$ is comparable with that of filtrate flux decline. It was also found that fast flux decreasing was observed over the binary mixture containing casein. The result is due to high value of the initial resistance of the protein deposit ($R_{po}$) over casein.

• Microbiology and Biotechnology Letters
• /
• v.40 no.2
• /
• pp.128-134
• /
• 2012

Foot and mouth disease (FMD) is one of the most notorious and contagious viral diseases afflicting cloven-hoofed animals. In this study, the physicochemical properties of leachate from a FMD landfill site at 773-1, Waryong, Andong, Korea and the ground water from 777, Waryong, Andong, Korea, were analyzed for 1 year from December $10^{th}$ 2010 to November $17^{th}$ 2011. The leachate was collected from the FMD landfill site during March, May, July, September and November, 2011 and changes in pH, brix, water content, insoluble solids, crude proteins, crude lipids, total and reducing sugars and ash content were determined. Considering the annual profiles of temperature and rainfall at the FMD landfill site, the dramatic changes in the physicochemical properties of the leachate from March to July, and especially from May to July, such as increases in pH, and a rapid reduction of brix and organic matter, may be closely linked to the growth of microorganisms in the leachate. The sharp decreases in the concentration of biominerals, such as Mg, Ca, and Fe from 1073, 4311 and 56.2 ppm in March to 151, 78, and 0.1 ppm in November, further suggest that decreases in organic matter in the leachate result from degradation by microorganisms originating from the intestines of the livestock. Analysis of the profiles of the organic materials in the leachate revealed that the properties of the leachate were similar to those of excremental matter-derived water. These results could be applied to a number of fields for the analysis of organic matter behavior, the development of the degradation process, and risk analysis in the environment for hygiene and food industries, of leachate from FMD landfill sites.

• Composites Research
• /
• v.30 no.2
• /
• pp.116-125
• /
• 2017

The purpose of this study is to develop silicon carbide fiber showing an excellent mechanical properties under highly oxidative conditions at high temperature. Polycarbosilane(PCS) as a preceramic precursor was used for making the SiC fiber. PCS fiber was taken by melt spinning method followed by melting the PCS at $300{\sim}350^{\circ}C$ in N2 gas. The Curing of PCS fiber was carried out in air oxygen chamber, prior to high temperature pyrolysis. Degree of cure was calculated by characteristic peak's ratio of Si-H to $Si-CH_3$ in FT-IR spectra before and after curing of PCS fiber. The properties of SiC fiber was affected greatly by the degree of cure. The SiC fiber produced by controlling fiber tension during heat treatment showed good properties. The SiC fiber exposed to $1000^{\circ}C$ at air from 1 min. up to maximum 50 hrs showed around 60% reduction in tensile strength. We found that large amount of carbon content on the fiber surface after long-term exposure has resulted in lower tensile strength.

• Applied Chemistry for Engineering
• /
• v.9 no.6
• /
• pp.829-834
• /
• 1998

Concerned with environmental issue, a new decomposition method for CFCs that caused the destruction of ozone layer was proposed. Using thermal plasma process, CFC113 decomposed completely. In order to quantify the tendency in decomposition and recombination of CFC113, thermodynamic equilibrium calculations were performed. The calculation was conducted with CFC113, $H_2$, $O_2$ at 1 atm and 300 K~5000 K. In the experiment, products which are generated after decomposition in the plasma were examined by varying reacting gases($H_2$, $O_2$) flow rates and the changes of inside diameters of quenching tubes. Decomposition products were analyzed using Gas Chromatograph. The results are very promising with a decomposition efficiency greater than 99.99%. As to CFC113/$H_2$=1/3, conversion to CO decreased with increasing $O_2$ ratio. When CFC113/$O_2$=1/1, 1/1.5 and 1/2, conversion to CO increases above $H_2$ ratio of 3. The change of CO conversion is not sensitive to power changes. As total flow rate increased, CO conversion was slightly decreased. When the inside diameter of the quenching tube was changed from 8mm into 4mm, CO conversion was increased due to enhanced quenching rate.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.6
• /
• pp.138-146
• /
• 2008

The chemical compositions, cell wall biopolymers and non-isothermal behavior of the stem biomass of Nicotiana Tabacum originated from tobacco industry were investigated in depth. On a weight basis, the contents of total ash and total sugar are 19.1% and 20.7% respectively. Lignin content was around 3% of tobacco stem biomass while pectin was over 7%. The holo-cellulose content in cell wall biopolymer was around 13% and the $\alpha$-cellulose constitutes 60% of the total holo-cellulose. The thermal behavior of stem biomass showed different patterns depending on either inert (nitrogen) or oxidizing (air) atmospheric condition. In the air atmosphere, the rapid thermal decompositions at around $473^{\circ}C$ and $581^{\circ}C$ were recorded as the peaks in DTG curve, while the peaks were not shown in the nitrogen atmosphere condition. The thermal analysis of the freeze dried soluble obtained from hot water extraction of tobacco stem biomass showed that the rapid thermal decomposition at around $581^{\circ}C$ in the air atmosphere was due to the residual char originated from the soluble fraction. The distinct difference in thermal decomposition between hemicellulose and cellulose were easily found in the DTG curve obtained in the nitrogen atmosphere.