• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.14 no.2
• /
• pp.169-178
• /
• 2016

The properties of wastes for melting need to be considered to minimize the maintenance of refractory and to discharge the molten slags smoothly from a plasma torch melter. When the nonflammable wastes from nuclear facilities such as concrete debris, glass, sand, etc., are melted, they become acid slags with low basicity since the chemical composition has much more acid oxides than basic oxides. A molten slag does not have good characteristics of discharge and is mainly responsible for the refractory erosion due to its low liquidity. In case of a stationary plasma torch melter with a slant tapping port on the wall, a fixed amount of molten slags remains inside of tapping hole as well as the melter inside after tapping out. Nonmetallic slags keep the temperature higher than melting point of metal because metallic slags located on the bottom of melter by specific gravity difference are simultaneously melted when dual mode plasma torch operates in transferred mode. In order to minimize the refractory erosion, the compatible refractories are selected considering the temperature inside the melter and the melting behavior of slags whether to contact or noncontact with molten slags. An acidic refractory shall not be installed in adjacent to a basic refractory for the resistibility against corrosion.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.4
• /
• pp.498-505
• /
• 2020

Aggregate occupies about 70-85% of the concrete volume and is an important factor in reducing the drying shrinkage of concrete. However, when constructing high-rise buildings, it acts as a problem due to the high load of natural aggregates. If the load becomes large during the construction of a high-rise building, creep may occur and the ground may be eroded. Material costs increase and there are financial problems. In order to reduce the load on concrete, we are working to reduce the weight of aggregates. However, artificial lightweight aggregates affect the interface between the aggregate and the paste due to its higher absorption rate and lower adhesion strength than natural aggregates, affecting the overall strength of concrete. Therefore, in this study, in order to grasp the interface between natural aggregate and lightweight aggregate by type, we adopted a method of measuring electrical resistance using an EIS measuring device, which is a non-destructive test, and lightweight bone. The change in the state of the interface was tested on the outside of the material through a blast furnace slag coating. As a result of the experiment, it was confirmed that the electric resistance was about 90% lower than that in the air-dried state through the electrolyte immersion, and the electric resistance differs depending on the type of aggregate and the presence or absence of coating. As a result of the experiment, the difference in compressive strength depending on the type of aggregate and the presence or absence of coating was shown, and the difference in impedance value and phase angle for each type of lightweight aggregate was shown.

• Journal of Wetlands Research
• /
• v.6 no.3
• /
• pp.55-70
• /
• 2004

The wetland ecosystem is a complex products of various erosion force, accumulation as water flows, hydrogeomorphic units, seasonal changes, the amount of rainfalls, and other essential element. There is no single, correct, ecologically sound definition for wetlands because of the diversity of wetlands and the demarcation between dry and wet environments occurs along a continuum, but wetland plays various ecosystem functions. Despite comprehensive integration through classification and impact factors there is still lacking in systematic management of wetlands. Classification system developed by the USFWS(1979) is hierarchical progresses from systems and subsystems at general levels to classes, subclasses, dominance types, and habitat modifiers. Systems and subsystems are delineated according to major physical attributes such as tidal flushing, ocean-derived salts, and the energy of flowing water or waves. Classes and subclasses describe the type of substrate and habitat or the physiognomy of the vegetation or faunal assemblage. Wetland classes are divided into physical types and biotic types. For the wise management of wetlands in Korea, this study was carried out to examine methodology of USFWS classification system and discuss its application for Korean wetland hydrogeomorphic units already known. Seven wetland types were chosen as study sites in Korea divided into some different types based on USFWS system. Three wetland types belonging to palustrine system showed no difference between Wangdungjae wetland and Mujechi wetland, but Youngnup of Mt. Daeam was different from the former two types at the level of dominant types. This fact means that setting of classification system for management of wetland is needed. Although we may never know much about the wetland resources that have been lost, there are opportunities to conserve the riches that remain. Extensive inventory of all wetland types and documentation of their ecosystem functions are vital. Unique and vulnerable examples in particular need to be identified and protected. Furthermore, a framework with which to demonstrate wetland characteristics and relationships is needed that is sufficiently detailed to achieve the identification of the integrity and salient features of an enormous range of wetland types.

• Korean Journal of Soil Science and Fertilizer
• /
• v.18 no.3
• /
• pp.289-296
• /
• 1985

To clarify the soil characteristics and genesis of the clayey terrace soils distributed in Yeongcheon (inland region) and Yeongil (coastal region), 9 typifying pedons including a recent local deposits were studied. The physico-chemical properties found were summarized as follows; 1. The contents of available water of the terrace soils were ranged from 12.0 to 20.3%. They were increased with increaseing clay content up to 35%, and then decreased at clay content of 35 to 55%, but were maintained about 12 to 13% when the clay content exceeds 55%. 2. The amount of water stable aggregates in the surface soils were ranged from 55.0 to 81.1%, and were low in cultivated upland where water erosion were accelerated while high in the paddy where the double cropping were practiced. The index of aggregate in cultivated upland were higher in the surface soils but the paddy soils were higher in subsoils. 3. The colloidal reactions checked by the differences between pH in $0.01N-Na_2SO_4$ and $H_2O$ indicate exchangeable acidity to exchangeable neutrality, which means a sort of Red-yellow soil forming process had been prevailed during genesis of the terrace soils. 4. Cation exchange capacity of the clayey terrace soils were averaged about 15.8-20.2me/100g of fine earth and 35.6-52.6me/100g of clay. The rates of base saturation were 32.7 to 57.6% and the rates decreased with increasing the elevations of terraces. 5. The activities of free iron oxides were 0.061 to 0.739 and the values decreased with increasing elevation while the crystallinity index of iron oxides positively correlated with elevations the values ranged from 0.067 to 0.537.

• Korean Journal of Soil Science and Fertilizer
• /
• v.6 no.1
• /
• pp.35-52
• /
• 1973

Red Yellow Soils occur very commonly in Korea and constitute the important upland soils of the country which are either presently being cultivated or are suitable for reclaiming and cultivating. These soils are distributed on rolling, moutain foot slopes, and terraces in the southern and western parts of the central districts of Korea, and are derived from granite, granite gneiss, old alluvium and locally from limestone and shale. This report is a summary of the morphology, physical and chemical characteristics of Red Yellow Soils. The data obtained from detailed soil surveys since 1964 are summarized as follows. 1. Red-Yellows Soils have an A, Bt, C profile. The A horizon is dark colored coarse loamy or fine loamy with the thin layer of organic matter. The B horizon is dominantly strong brown, reddish brown or yellowish red, clayey or fine loamy with clay cutans on the soil peds. The C horizon varies with parent materials, and is coarser texture and has a less developed structure than the Bt horizon. Soil depth, varied with relief and parent materials, is predominantly around 100cm. 2. In the physical characteristics, the clay content of surface soil is 18 to 35 percent, and of subsoil is 30 to 90 percent nearly two times higher than the surface soil. Bulk density is 1.2 to 1.3 in the surface soil and 1.3 to 1.5 in the subsoil. The range of 3-phase is mostly narrow with 45 to 50 percent in solid phase, 30 to 45 percent in liquid one, and 5 to 25 percent in gaseous state in the surface soil; and 50 to 60 solid, 35 to 45 percent liquid and less than 15 percent gaseous in the subsoil. Available soil moisture capacity ranges from 10 to 23 percent in the surface soil, and 5 to 16 percent in the subsoil. 3. Chemically, soil reaction is neutral to alkaline in soils derived from limestone or old fluviomarine deposits, and acid to strong acid in other ones. The organic matter content of surface soil varying considerably with vegetation, erosion and cultivation, ranges from 1.0 to 5.0 percent. The cation exchange capacity is 5 to 40 me/100gr soil and closely related to the content of organic matter, clay and silt. Base saturation is low, on the whole, due to the leaching of extractable cations, but is high in soils derived from limestone with high content of lime and magnesium. 4. Most of these soils mainly contain halloysite (a part of kaolin minerals), vermiculite (weathered mica), and illite, including small amount of chlorite, gibbsite, hematite, quartz and feldspar. 5. Characteristically they are similar to Red Yellow Podzolic Soils and a part of Reddish Brown Lateritic Soils of the United States, and Red Yellow Soils of Japan. According to USDA 7th Approximation, they can be classified as Udu Its or Udalfs, and in FAO classification system to Acrisols, Luvisols, and Nitosols.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.1
• /
• pp.139-146
• /
• 2015

The amount of by-product from sulphur increases in domestic industrial facilities. However, the amount of its consumption is limited so that the amount of unused sulphur continues to increase. Therefore, in this study, the use sulfur polymer as the concrete surface protecting material was conducted. The compressive strength showed that as the substitution ratio of filler increased up to 40%, the compressive strength also increased. A high compressive strength was shown at the curing temperature of $40^{\circ}C$ (SS, FA) and $60^{\circ}C$ (OPC) according to the type of filler. The difference of compressive strength between air dry curing and water curing was insignificant so that there was no significant influence of moisture during curing process. The evaluation result of bond strength showed that the highest bond strength was shown at the air-dry condition of $40^{\circ}C$ regardless of type of filler. Bonding didn't occur properly during water curing in comparison to air dry curing. Also, in case of the specimen cured at $60^{\circ}C$, discoloration and hair cracks appeared due to the influence of temperature, and the highest bond strength was shown at the substitution ratio of 20% (SS, FA) and 30% (OPC) according to the type of filler. The releasing test result of harmful substance showed that no harmful substance was released, so there is no harmfulness in the surface protecting material using sulfur polymer. As a conclusion drawn in this study, it is most appropriate to substitute silica by approximately 20%, mix and cure at the air-dry condition of $40^{\circ}C$ in order to use sulfur polymer as the surface protecting material.