• Annual Conference of KIPS
• /
• 2017.04a
• /
• pp.1193-1194
• /
• 2017

실시간으로 화재 발생을 감지하고 관리자와 사용자에게 알리기 위해 본 연구에서는 센서와 드론을 활용한 스마트 빌딩 화재 알림 시스템을 제안한다. 시스템은 스마트센서, 드론, 컨트롤서버, 관리자앱으로 구성되어 있다. 온도감지 센서를 통해 빌딩 내부의 온도를 실시간으로 전송하고 온도가 일정 범위를 벗어난 경우 관리자에 알림 메시지를 보내고 드론에게 정찰 명령을 보낸다. 관리자는 전송된 온도와 드론이 정찰한 사진을 확인하여 화재를 파악하고 화재발생의 경우 빌딩 내부의 모든 사용자에게 알림 메시지를 전송한다. 이를 통해 기존의 CCTV 보다 화재 상황에 대해 좀 더 능동적이면서 빠르고 정확하게 대응할 수 있으며 나아가 화재 신고 및 원인 규명에도 도움이 될 것이다.

• Fire Science and Engineering
• /
• v.31 no.3
• /
• pp.73-78
• /
• 2017

In this paper, the fire risk using a bimetal type thermometer for construction installation is presented. Because construction equipment is used widely in the field and the site is exposed to explosions and fire by combustible gas or fume, strong restrictions on the structure and usage are applied. Moreover, the risk of fire increases as precise temperature measurements are poorly conducted via an inner temperature sensor inside construction furnace. Therefore, this paper presents the results of structural analysis of a bimetal temperature sensor which is used widely in construction installation and temperature measurement experiments relative to the material property of the target object. The results revealed the relatively precise temperature of the liquid object, whereas those of the gas and solid object showed a lower temperature compared to the real temperature. This shows that bimetal-type temperature sensor is more suitable for measuring a liquid state object than measuring a gas or solid state object.

• Fire Science and Engineering
• /
• v.11 no.2
• /
• pp.11-17
• /
• 1997

The objective of this research is to study on the decision of the interface height in a room in case of trashcan, chair, carpet and sofa as a fire starter in a residential room by performing the experimental studies. For the decision of the interface height, the temperatures of various positions in fire room are measured and the averaged temperatures are calculated from these measured temperatures every time and height. The temperatures of all positions in fire room are obtained as the basis of the measured temperatures and the middle point of the highest temperature slope is decided as the interface point. The interface heights were distinct and were around 1[m] maintaining constant state. However, at the time of the maximum temperature, the interface height was lowered to 0.25[m]-0.75[m] from the floor.

• Nuclear Engineering and Technology
• /
• v.26 no.4
• /
• pp.471-483
• /
• 1994

A sodium fire facility with a test chamber of 1.7㎥ volume was constructed and operated to carry out experiments of sodium fires such as pool, spray, and columnar fires which might take place in sodium-related facilities. The experimental results of pool fires showed that the increase of temperature and pressure in the test chamber was much smaller than that of spray and columnar fires even though their amount of sodium injection in the chamber was much larger compared to other types of fires. And it was found in pool fires that the temperatures of sodium pool and the gas temperature in the test chamber had been maintained much longer than other types of fires, and that the chamber pressure had come to vacuum due to depletion of the oxygen for a large amount of sodium injection in the chamber. The experimental results of spray fires showed that sprayed sodium of small particles instantly reacted with oxygen, and that its reaction heat increased gas temperature and pressure of the test chamber rapidly and decreased them shortly. And the maximum gas temperature and pressure of the test chamber in spray fires ore greatly changed according to the inlet sodium temperature in the test chamber. The characteristics of the columnar fires were almost similar to those of spray fires, but the maximum temperature and pressure of the test chamber were much smaller even for a large amount of sodium injection. And it was shown in spray and columnar fires that the temperatures at each measurement position in the test chamber were quite different due to the instantaneous sodium oxidation in comparision with pool fires. Finally, the graphex powder was proved to be a very effective extinguisher against sodium pool fires.

• Fire Science and Engineering
• /
• v.21 no.1 s.65
• /
• pp.51-59
• /
• 2007

The purpose of this study is analyzing the fire behavior according to the fire load for G underground shopping mall located in Daegu city. when predict fire behavior, fire load and ventilation coefficient are important factor who dominate fire temperature or fire continuance time. Therefore, size of unit room, opening size and inflammable investigated on the field. Fire load calculated using unit calorific value by each material of inflammable that investigate. And reduction model experimented fire load about 6 models with variable. Fire behavior analyzed by heat flows of inside space that temperature rise and temperature change by time of fire source.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2011.04a
• /
• pp.378-383
• /
• 2011

지능형 터널 배연시스템은 터널상부의 온도를 감지하는 온도감지부에서 들어오는 신호를 해독하여 화재위치 및 화재크기를 선정하고 제연설비의 운전방향 및 배연량을 조절함으로써 연기를 효율적으로 제어할 수 있는 시스템이다. 지능형 터널 배연시스템의 성능을 검증하기 위하여 실물터널의 크기를 1/60로 축소한 모델에서 두가지의 화원위치에 따라 실험을 수행하였다. 화재 발생 후 초기에는 온도가 상승하다가 제연팬이 작동하면 온도가 급격히 낮아진 후 일정하게 유지되면서 서서히 증가한다. 터널화재시 승객의 피난 장애를 주는 연기의 제어를 통해 터널의 안전성을 향상시킬 수 있는 것을 확인하였다.

• Fire Science and Engineering
• /
• v.23 no.2
• /
• pp.41-48
• /
• 2009

In this paper, to overcome the limitation of the existing wired fire sensors and alert facilities, the real-time temperature data collected from the fire detectors applied USN is analyzed the time series and spacial features of temperature inside building using the GIS spatial modeling method. Resulting from the analysis of the distribution features by the spacial location and time series, the temperature sensors applied USN is installed by the consideration of the spacial structures features. This paper will suggest the objective and practical guideline of installation of fire sensors applied USN.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05a
• /
• pp.393-395
• /
• 2011

기존의 화재 감시 시스템은 보통 연기, CO 혹은 온도와 온도의 변화량을 가지고 화재 여부를 판단하였다. 대부분의 각각의 센서에서 측정된 값을 가지고 미리 설정한 값과 비교하여 기준을 넘었을 경우에 화재라고 결정한다.건물 내부에 화재가 발생하였을 경우에는 연기와 고열로 인하여 접근이 어려울 경우가 대부분이다. 사람의 손이 닿지 않는 경우에 화재 감시반 센서모듈을 통하여 고열과 가득한 연기로 인한 내부 환경을 판정하여서 화재상황을 인식하는 방식을 제안한다.

• Fire Protection Technology
• /
• s.28
• /
• pp.23-29
• /
• 2000

• 방재와보험
• /
• s.89
• /
• pp.52-59
• /
• 2001