• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.1
• /
• pp.63-73
• /
• 2021

This paper presents a algorithm for automatic target recognition robust to the influence of the flame in order to track the target by EOTS(Electro-Optical Targeting System) equipped on UAV(Unmanned Aerial Vehicle) when there is aerial target or marine target with flame at the same time. The proposed method converts infrared images of targets and flames into a gradient vector field, and applies each gradient magnitude to a polynomial curve fitting technique to extract polynomial coefficients, and learns them in a shallow neural network model to automatically recognize targets and flames. The performance of the proposed technique was confirmed by utilizing the various infrared image database of the target and flame. Using this algorithm, it can be applied to areas where collision avoidance, forest fire detection, automatic detection and recognition of targets in the air and sea during automatic flight of unmanned aircraft.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.6
• /
• pp.173-180
• /
• 2003

This paper deals with the experimental results that apply to a new wire by an artificial flame-maker because it's difficult to directly analyze the characteristic of deterioration by a forest fire. Those results include surface characteristics for a conductor. In addition, there's been an experiment and analysis about the surface characteristics of the wire of ACSR 480$\textrm{mm}^2$ which was removed from Pohang area by a forest fire. Then, the database will be made to predict the state of deteriorated wires by a forest fire using those two data, and data necessary to diagnose the life state of an ACSR wire affected by a forest fire will be given.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.3
• /
• pp.67-75
• /
• 2019

The laminar burning velocity of endothermic fuel surrogates is measured in this study, in order to investigate combustion characteristics of aviation fuel after being used as coolant in an active cooling system of a hypersonic flight vehicle. A Bunsen burner was manufactured such that the laminar burning velocity can be taken for two types of surrogate fuels, SF-1 and 2. The results showed that the burning velocity of surrogate fuels was faster at high equivalence ratio conditions than that of the reference fuel (RF), and specifically, the velocity of SF-1 had the maximum value at the highest equivalence ratio compared with those of SF-2 and RF.

• Fire Science and Engineering
• /
• v.26 no.6
• /
• pp.85-91
• /
• 2012

To reduce human life and property damage at the fire in a building, it is most critical to control flame spread in the early stage. Fire spread prevention measure generally includes fire resistance performance securing of structure member in the arson zone and use limitation based on combustion performance of finishing material. The latter is most fundamental fire safety design to determine flame spread, but domestic combustion test determines combustion performance by specimen sized fire test method. Thus, there are many restrictions in the determination of combustion performance by composite material such as sandwich panel. Especially, outer finishing material uses a variety of composite material such as dry bit, aluminum composite panel, and metal panel compared to inner finishing material. Therefore, this study would determine vertical fire spread features by a full scaled fire experiment through the test method of ISO 13785-2, an international test standard.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.213-216
• /
• 2009

In order to see the flame behavior in the gas turbine combustor, combustion test was performed by using sector combustor. Ignition test with torch ignition system was carried out at the various combustor inlet velocity and air fuel ratio. Also, flame blow out limit was measured by changing fuel flow rate with fixed air mass flow rate. In the test results, stable ignition is possible at air excess ratio of 6 and this limit is gradually increased with combustor inlet air velocity. The minimum blow out limit is about 4 at 40 m/s of combustor inlet velocity. This blow out limit is also increased up to about 10 with increasing combustor inlet velocity.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2013.04a
• /
• pp.173-174
• /
• 2013

액체로켓 시험설비는 다량의 연료를 사용하므로 사고 발생의 가능성이 높다. 또 발생 가능한 폭발/화재 사고는 과도한 폭발과압 및 화염구로 인해 많은 손실을 가져 올 수 있다. 이에 액체로켓엔진 시험설비에서 발생 할 수 있는 사고의 유형 및 손실 정도에 대해서 연구 하였다. 본 문서에서는 액체로켓 시험설비에서 발생 할 수 있는 폭발 및 화재에 적합한 방재 방법에 관한 내용을 담고있다.

• Fire Science and Engineering
• /
• v.28 no.3
• /
• pp.34-42
• /
• 2014

The concentrations of inert gases ($N_2$, Ar, $CO_2$ and He) required to induce the flame instabilities such as swing, rotation, lifted and blow-out were measured in a cup burner nonpremixed flames for $CH_4$ and $C_3H_8$ fuels. Quantitative differences in the extinguishing concentration with fire suppression criteria (i.e. blow-out or onset of flame instability) were also examined. It was found that the difference in extinguishing concentration was increased with the appearance of lifted flame and the low extinguishing performance of inert gaseous. The maximum difference in extinguishing concentration with the suppression criteria was approximately 35% at the highest fuel velocity condition (1.3 cm/s) for the $C_3H_8$-air nonpremixed flame. It can be also expected that the extinguishing concentration by the criteria based on the onset of flame instability will provide the useful information from the viewpoint of the accurate and economical design concentration.

• Journal of the Korean Institute of Gas
• /
• v.19 no.5
• /
• pp.36-40
• /
• 2015

To evaluate the safety of propane cylinder, the flame test was performed by the flame exposure scenario of propane cylinder. The cylinder which was exposed in a flame was rapidly occurred to increase the internal pressure by liquid expansion, if so it cause of physical explosion. Therefore, the cylinder which was applied with thermal pressure relief device sholud be not bursted and the propane should be discharged to outside safely. The flame average temperature that was around of cylinder is $600^{\circ}C$, and then it increased $700^{\circ}C$ by discharged propane. The result of flame test, the cylinder was deformed, but it was not bursted. The regulations of flame exposure test for propane cylinder were not restricted, this paper can be applied to restrict the flame test if the cylinder is possible to expose the flame. Also, the results is expected as reference for estimation of the pressure cylinder performance.

• Korean Chemical Engineering Research
• /
• v.48 no.5
• /
• pp.603-608
• /
• 2010

A study has been conducted experimentally to investigate behavior of ignition and flame spread over metal dust deposits with particle size using by a developed apparatus and thermogravimetric analysis(TGA). Zr, Ta and Mg-Al(90:10 wt%) alloy metal powders including Mg and Ti with different particle size were used. Also we used PMMA(Polymethylmethacrylate) powder to compare the combustion properties to those of metal powders. When dust layers were more than 5 mm in thickness, the dependency of deposit depth on flame spread rate over dust layer was not shown. With decreasing mean particle diameter, flame spread rate over Ti dust layer decreased, while the spread rate over Mg dust layer increased. For mean diameter of $51{\mu}m$, fire spread rate over pure Mg dust layer decreased to about 50 percent in Mg-Al(90:10 wt%) dust layer. The oxide thickness of metal dust used in this study tended to be inversely proportional with the spread rate, and it was quite small for influence with particle size. From the results of TGA for Ti and Mg, weight increasing curves(550 for Mg, 578 for Ta) were observed in the oxidation process, and they seems to be caused by ignition of upper dust layer.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.04a
• /
• pp.2-2
• /
• 1998

현대우주항공(주)가 미국의 AlliedSignal사와 함께 국제 공동 개발중인 10MW급의 ASE120 엔진은 항공용 엔진을 산업용으로 개조한 개조형 엔진으로서 희박 예혼합 예기화(Lean Premix prevaporization) 방식의 연소기를 쓰고 있다. 이 연소기는 연소에 관여하는 공기량을 부하에 따라 가감하여 일정 공연비를 유지하는 air staging법을 사용하고 있으며 이로써 연소화염온도를 일정치로 조절하여 연소중 생성되는 유해가스의 양을 목표치 이하로 제어한다. 연소화염온도 설계치는 2912$^{\circ}$F이며 배기가스 발생량은 NOx, CO모두 궁극적으로 10ppmv 이하를 목표로 하고 있다. 이러한 건식 저 배기가스(Dry Low Emission) 연소기가 그 역할을 다하기 위하여는 양호한 혼합기를 확보하는 것이 선결 문제이다. 본 연구소에서는 두 개의 혼합기(mixing can)가 180$^{\circ}$ 간격으로 환형 연소기(annular type)에 접선 방향으로 설치되어 대칭을 이루고 있고 혼합기의 혼합성능을 측정하기 위하여 제작된 시험장치에는 하나의 혼합기만을 쓰고 있다.