• 한국가시화정보학회:학술대회논문집
• /
• 2005.04a
• /
• pp.61-83
• /
• 2005

연소현상의 가시화를 위한 몇 가지 레이저 진단기법의 응용 예를 소개한다. 이에는 유동 가시화를 위한 반응성 Mie 산란, 주화학종의 계측을 위한 Rayleigh 및 Raman 산란, 미소화학종 계측을 위한 레이저유도 형광법, 온도계측을 위한coherent anti-Stokes Raman 산란법 및 매연계측을 위한 광 소멸/산란법 등이 포함된다. 이러한 기법들이 확산화염, 층류 및 난류 부상 화염, 비예혼합 와도 내의 화염전파, 매연생성 등의 연구에 적용되어 물리적 메커니즘을 이해하는데 유용하게 적용된 사례를 보고한다.

• 한국가시화정보학회:학술대회논문집
• /
• 2005.04a
• /
• pp.115-154
• /
• 2005

SI 엔진의 연소특징은 비정상 난류 예혼합 화염이며 여기서 내부 유동은 직접 화염 전파에 영향을 미치며 난류와 거시적 유동의 패턴 모두 중요한 역할을 한다. 내연기관 연소에서 난류는 매우 중요한 역할을 하고 통상 엔진 속도($\approx$흡입유동 속도)에 비례하며 그 주요 역할은 고속 운전 시 해당 사이클 내에 연소가 완료되는 데 기여하지만 출력저하, 제어 및 측정 그리고 사이클 변동과 관련하여 실질적으로 난류 제어를 통한 엔진 성능 개선은 사실상 불가능하다. 실물 엔진의 성능 파라미터로 주로 유동의 거시적 거동이 사용되며 이 유동과 연료 분사계가 혼합기 분포 상태와 화염 전파 방향을 결정하여 최종적으로 엔진의 성능을 지배한다. 따라서 가시화를 통한 연소 진단도 이 현상에 주목할 필요가 있으며 거시적 파라미터를 성능에 연관하는 다양한 기법이 존재하고 이들은 매우 풍부한 데이터베이스를 통해 비교적 정확한 성능의 예측을 가능하게 하고 이 점에 주목한 엔진만 성공을 거두었다. 이 거시적 현상에 주목하여 가시화를 통해 성층화 현상을 실험적으로 해석한 예를 제시하였다. SI 엔진 가시화에서 기법보다 중요한 것은 현상의 이해이다. 이를 위해 성공적 가시화 진단을 위해서는 우선 현상에 대한 모델링이 필요하고 이 모델에서 가시화를 통해 규명 가능한 현상을 추출해 내는 것이다.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1994.11a
• /
• pp.84-89
• /
• 1994

주유동에 수직으로 분사된 제트 화염의 구조는 이해하기 위하여 화염 길이와 온도를 측정하고 reactive mie scattering 방법을 이용하여 단면 가시화를 실시하였다. 주유동 속도와 제트 분사 속도의 증가에 따라 화염 길이도 함께 증가함을 알 수 있고, 단면 가시화 결과 화염 내부에 존재하는 inner vortical structure는 일반적인 동축제트 화염과 같은 대칭 구조를 갖지 앉고 유동 조건에 따라 inner vortical motion 의 생성 위치가 변화함을 알 수 있다 이는 본 유동장의 특성 중의 하나인 bound vortex와 제트와 주유동이 접하는 상류 면에서 발생하는 rolling-up 의 강도에 좌우됨을 알 수 있다.

• 한국가시화정보학회:학술대회논문집
• /
• 2005.12a
• /
• pp.74-79
• /
• 2005

The tribrachial flame in laminar coflow jet has been investigated experimentally with unsteady propagating condition. With adopting various visualization techniques, including OH-PLIF, Rayleigh Scattering technique, it was confirmed that the location of tribrachial point is on the inclined surface of flame and the propagation speed of tribrachial flame was significantly affected by the velocity gradient.

• Journal of the Korean Society of Visualization
• /
• v.14 no.3
• /
• pp.51-58
• /
• 2016

New concept spark plug was developed to study its influence on the combustion characteristics of SI engine. It has pre-ignition chamber at the lower end of spark plug and flame hole, in which fresh mixture gas can be put in through the flame hole without any fuel supply system. This spark plug was tested in a single cylinder engine dynamometer for different air fuel ratio to measure the fuel consumption rate, emission gases, and MBT timing. And constant volume combustion chamber was made to understand flame characteristics of spark plug. New spark plug induced fast burn compared to the conventional spark plug and its effects were increased in lean air fuel ratio. Pre-ignition chamber spark plug with 5 holes which had adjusted size was more stable and effective in combustion performance than pre-ignition chamber spark plug with 1 hole. And its effects showed larger differences in lean air fuel ratio than stoichiometric condition. Flame kernel and flame growth process of conventional spark plug and pre-ignition chamber spark plug studied by flame visualization of schlieren method.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.12
• /
• pp.1375-1381
• /
• 2011

Combustion processes in an optically-accessible single-cylinder heavy-duty diesel engine equipped with a highpressure common-rail injection system were investigated for JP-8 and diesel. Direct imaging and two-color thermometry were employed to verify the emission trend for both fuels. The combustion process was characterized by image analysis with focus on luminosity. The results of two-color thermometry were analyzed on the basis of the flame temperature and KL factor distribution. Analysis of the combustion process by direct imaging showed that the ignition delay was longer for JP-8 than for diesel, while the flame was extinguished rapidly. Analysis of the flame luminosity showed that the combustion intensity was higher for diesel and that the flame lasted for a longer duration in this case. Two-color thermometry results showed that the high-temperature region extended over a large area during JP-8 combustion, implying the formation of a large amount of $NO_x$. In addition, the KL factor showed low level over a large area and relatively homogeneous in the case of JP-8 combustion, which implied that less smoke was produced when using this fuel.

• Journal of the Korean Society of Visualization
• /
• v.11 no.1
• /
• pp.22-27
• /
• 2013

An investigation into the influence of ultrasonic standing wave on the structural behavior of propane/air premixed flame has been made to get a clue to the combustion reaction acceleration and combustion instability. Visualization technique utilizing the Schlieren photography was employed for the observation of structural variation of the flame reaction zone. Evolutionary characteristics of the flame front were caught by the high-speed Schlieren image, through which local flame velocity of the moving front were analyzed in detail.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.2 s.257
• /
• pp.132-140
• /
• 2007

The temperature and soot of the visualized diesel engine's turbulent flow of the flame was measured qualitatively. In the combustion chamber, in order to judge the affect that the swirl current has on the current ratio two heads with different ratios were used. Using a high speed camera, the results were analyzed using flame visualization. In order to measure the temperature and soot of the turbulent flames like diesel flames, two color methods were used to acquire temperature and the soot of the flames according to the conditions through analyzing the two wavelengths of the flames. It was possible to measure the highest temperature of the non-swirl head visualized engine, which is approximately 2400K, and that swirl head engine managed up to 2100K. With respect to the visualized diesel engine soot, we got the grasp of the KL factor which bears the qualitative information of the soot. This study is dedicated to suggesting the possibility of measuring not only the temperature but also soot of the diffusion flame of the diesel engine turbulent flames.

• Journal of the Korean Society of Visualization
• /
• v.9 no.4
• /
• pp.35-40
• /
• 2011

An experimental investigation of the characteristic of non-premixed lifted flames with nozzle hole-tone of high-frequency has been performed. Before the fuel was supplied to nozzle, the fuel was supplied through a burner cavity which was located under the nozzle. The fuel passed through the excitation cavity under the influence of the high-frequency affects the lifted flame characteristics. The measurements were performed in flow range that occurs lifted flame and blow out. When the high-frequency is generated from burner cavity, the lifted length became shorter, and noise reduced comparing to unexcitation case. Additionally, operating flow range was increased and diameter of flame base became smaller with high-frequency effect. Through this experiments, it's ascertained that the high-frequency excitation can be adopted with effective method for flame stability and noise reduction.

• Journal of the Korean Society of Visualization
• /
• v.2 no.1
• /
• pp.8-11
• /
• 2004

Conditional sampling measurement is required for conditional averages as well as unconditional Favre averages to resolve different flame structures of turbulent combustion. A Favre average can be obtained as an integral of conditional average and Favre PDF in terms of the mixture fraction, which is a preferred choice as a sampling variable in diffusion controlled turbulent combustion. MILD combustion data are presented as an example for a conditionally averaged data set and comparison with CMC calculation results.