• Journal of the Korea Society for Simulation
• /
• v.28 no.2
• /
• pp.1-14
• /
• 2019

A full scale hydrodynamic simulation that requires an accurate reproduction of shock-induced detonation was conducted for design of an energetic component system. A detailed hydrodynamic analysis SW was developed to validate the reactive flow model for predicting the shock propagation in a train configuration and to quantify the shock sensitivity of the energetic materials. The pyrotechnic device is composed of four main components, namely a donor unit (HNS+HMX), a bulkhead (STS), an acceptor explosive (RDX), and a propellant (BPN) for gas generation. The pressurized gases generated from the burning propellant were purged into a 10 cc release chamber for study of the inherent oscillatory flow induced by the interferences between shock and rarefaction waves. The pressure fluctuations measured from experiment and calculation were investigated to further validate the peculiar peak at specific characteristic frequency (${\omega}_c=8.3kHz$). In this paper, a step-by-step numerical description of detonation of high explosive components, deflagration of propellant component, and deformation of metal component is given in order to facilitate the proper implementation of the outlined formulation into a shock physics code for a full scale hydrodynamic simulation of the energetic component system.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.353-358
• /
• 2008

Inha Rocket Research Institute has made the igniter that is combination of black powder and PVA polymer for ignition small rocket. But recent igniter is not satisfy because of the performance of igniter is not identified. So, we confirmed requirement of igniter by comparing of ratio of black powder and PVA through experimental method. Especially we studied with ignition temperature for propellant and stable combustion pressure that is requirements of propellant. We can know the tendency of combustion properties by ratio of oxidizer and combustion catalyst through changing of temperature and pressure of exhaust gas of igniter.

• Explosives and Blasting
• /
• v.34 no.3
• /
• pp.1-9
• /
• 2016

The shaped charge were made for identifying the effect of controled blasting using relatively low VOD explosive for cutting rock mass with changing quality and thickness of metal liner. The metal liner was attached on both sides of a charge for directional cutting, when the shaped charge exploded in rock mass. Also, a efficiency of shaped charge was identified by concrete member experiment. And a center guide used for maintaining stand-off between shaped charge and hole wall. A case of Fe liner of thickness 0.8mm formed the deepest notch of experiments and the directional cutting of concrete member was identified.

• Tunnel and Underground Space
• /
• v.32 no.2
• /
• pp.160-172
• /
• 2022

The design regulations for simple explosive storage in Korea only stipulate standards for the materials and thickness of the wall of the structure because the amount of explosives that can be stored is small. There is concern about secondary damage during an internal explosion in a simple storage facility, and it is necessary to reexamine the current standards. The numerical analysis for the TNT 15 kg explosion inside the simple storage was carried out by setting the factors using the robust experimental design method. The displacement of the structure generated under the same time condition was analyzed, and the contribution was evaluated. The contribution of concrete thickness was the highest, and the contribution of concrete strength and rebar arrangement was lower than that of concrete thickness. The reinforcement diameter contributed extremely little to the displacement. The structural standards of the simple storage that are currently applied are insufficient on blast resistance, and it is necessary to present new design standards. Therefore, the design factor to be applied later analysis and actual experiments were taken into consideration. For the design variables, the thickness of the concrete was 15 cm considering the displacement, the concrete strength was selected as general concrete considering the inlet discharge pressure, the factor with the lowest average displacement was selected for the reinforcement arrangement and the diameter of the reinforcement, the factor with the smallest level was selected in consideration of economic feasibility because the difference in displacement was low.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.570-573
• /
• 2011

In this study, we described the Pyrovalve used in the propulsion system. It is very important to reduce Pyrovalve-debris as far as possible because Pyrovalve is a pyrotechnic device for controlling fuel and air line of propulsion system. So we focused on redesigning to reduce debris through several analyses and tests.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.327-330
• /
• 2009

A Through-Bulkhead Initiation Module(TBIM) using CH-6 was designed. The TBIM works as the shock-wave generated by a donor charge transmits to the acceptor charge. The structural safety of TBIM housing was calculated via modeling analysis, and the ignition characteristic was proved by 10 cc closed bomb test(CBT). The reliability analysis was made using Probit method on the basis of CBT results. The optimal bulkhead thickness of TBIM which is the most important design parameter was determined using reliability analysis.

• Explosives and Blasting
• /
• v.20 no.4
• /
• pp.29-37
• /
• 2002

발파진동 및 소음은 일반적으로 발생원인이 사회간접자본의 건설이나 자원 의 개발이라는 공익성과 관련되는 것이 대부분이다. 최근에는 환경문제에 대한 관심이 높아지면서 발파진동이나 소음에 대한 관심이 높고, 또한 많은 민원이 발생되고 있다. 아무튼 발파진동의 측정은 발파에 의해 발생하는 지반 및 구조물의 진동을 파악하여 발파진동 규제기준의 수행 여부를 평가하거나 또는 발파성능을 평가할 목적으로 관련 기관들에 의해 진동측정이 실시되고 있다. 따라서 규정의 준수에 대한 판정은 발파소음과 지반진동 측정의 정확도와 신뢰도에 의존하게 된다. 그러나 발파진동측정에 대한 통일적인 방법이나 지침이 없기 때문에 현장실무에서 측정방법이나 자료처리방법 등에 많은 어려움이 따르고 있다. 따라서 ISEE의 발파진동측정을 위한 실무지침을 중심으로 진동계측자료가 신뢰성을 보장하기 위한 작업의 일환으로 발파진동 측정시 고려해야 할 사항들에 대해 고찰함으로써 발파진동 측정방법에 대한 이해를 높이고자 한다.

• Explosives and Blasting
• /
• v.36 no.1
• /
• pp.1-11
• /
• 2018

In this study, several underwater steel cutting tests and AUTODYN numerical analyses were conducted to evaluate the penetration performance of a shaped charge device. Parameter analyses for the contribution rate were conducted by using the robust design method. The parameters adopted in this study were chamber type, stand-off, and wire setting, each of which had three levels in the analysis. Analysis results showed that the contribution rate was most affected by the stand-off, followed by the chamber type and wire setting. Experiments of underwater steel cutting were conducted at water depth of 25m. As expected, the experiments and numerical simulation showed similar results for underwater steel cutting performance, and thus the feasibility of the shaped charge device for underwater steel cutting at deep water depth was verified.

• Explosives and Blasting
• /
• v.34 no.4
• /
• pp.1-9
• /
• 2016

For underwater steel structure, cut that underwater shaped charge device that combines a spring hose, which is an external device of pressure resistance and flexibility with flexible shaped charge, was invented. As a basic experiment for an optimum condition design, an penetration performance was compared by external device shape. To evaluate the result of an experiment, image analysis was carried out after obtaining the model by using the liquid rubber for the penetrated steel plate. To simulate the penetrating process of shaped charge, the AUTODYN program has been used. As a result of analysis, while the average penetration depth of circular and square shaped external devices were similar, the penetration quality was more uniform in the case of circle. In addition, water infiltration occurred in square case, displacement and strain rate according to the increase of the water pressure were measured high.

• Explosives and Blasting
• /
• v.39 no.1
• /
• pp.1-9
• /
• 2021

As the national economic growth and the rapid increase in industrial structures are aging, the demand for removing steel structures is increasing, and research on improving the penetration performance of the linear shape charge explosives. In the study, numerical analyses were performed on the effect of the type of explosive used in the self-made shape charging container and the initiation method on the cutting performance of the steel plate and the effect on the shaped explosive installed close to it. ANSYS LS-DYNA, which can analyze the large deformation problem of materials due to explosion, was used, and an ALE(Arbitrary-Lagrange-Eulerian) model was applied that enables interlocking analysis of gases, liquids, and solid.