• Journal of Intelligence and Information Systems
• /
• v.3 no.2
• /
• pp.11-22
• /
• 1997

본 연구에서는 비선형 최적화 문제를 효율적으로 해결하기 위한 혼합유전알고리즘(Hybrid Genetic Algorthm : HGA)을 개발하였다. HGA는 기존 유전알고리즘의 적용에 있어 문제점으로 지적된 정밀도의 적용문제와 벌금함수의 사용을 배제하였으며 지역적최적점으로 빠르게 수렴하는 기존의 지역적 탐색법과 유전알고리즘 적용이후 수렴된 해 주변에 대한 정밀탐색법을 함께 고려하여 설계하였으며 이를 세가지의 비선형 최적화 문제 적용하여 본 논문에서 개발한 HGA의 유효성을 보였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.103-103
• /
• 2004

실제 작용하는 하중상태는 요소의 형상과 작용하중의 복잡성 때문에 혼합모드 하중상태를 나타낸다. 또한 혼합모드 피로균열은 전파과정 동안 부재의 구속형상이나 외부 작용하중의 급격한 변화에 의해서도 영향 받게 된다. 이로 인하여 피로균열은 균열선단에서 지속적이면서 급격한 응력 재분배의 상태를 경험한다. 그러므로 다양한 응력 재분배 상태에서의 혼합모드 피로균열에 대한 고찰이 필요하다. 본 연구에서는 응력 재분배상태 하에서 나타나는 혼합모드 피로균열의 전파거동에 대한 특징이 실험적으로 고찰되었다.(중략)

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.113-113
• /
• 2004

실제 사용중인 기계나 기계구조물은 다양한 환경 및 복잡한 설계조건으로 인하여 변동하중과 다축에서 작용하는 혼합모드 하중 상태에 놓이는 경우가 대부분이다. 하지만, 순수 모드 I 하중상태 하에서의 연구는 활발히 이루어졌으나, 실제 구조물에서 대부분 발생하는 혼합모드 하중상태 하에서의 연구는 아직 부족한 실정이다. 또한 기계구조물내의 많은 성분요소에 존재하는 작용 하중 방향에 수직적이지 않게 되며, 초기균열의 균열선상에서 성장하지 않는다.(중략)

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.10a
• /
• pp.226-226
• /
• 2003

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.10a
• /
• pp.233-233
• /
• 2003

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.103-104
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.06a
• /
• pp.725-726
• /
• 2007

• Journal of the Korean Magnetics Society
• /
• v.8 no.2
• /
• pp.86-92
• /
• 1998

Homegeneous feedstock is necessary to make plastic magents with uniform magnetic properties, therefore the optrimized mixing route and the homogeneity evaluation method are demanded. In this paper, method of homogeneity evaluation and effect of homogeneity on the magnetic prperites were investigated using Sr-ferrite /EVA plastic magnets. The feedstocks with different homogeneity were prepared using batch mixer and single screw extruder. The homogeneities of feedstocks were tested by torgue sensor, capilary rheometer, and measurement of magnetic properties. Mixing torque measurement using torque sensor was an effective method to determine the critical powder loading, but it was nor suitable to suitable to determine the feedstock mixing quality. Particle alignment measurement of a plastic magent was very accurate to evaluate the homogeneity, but expensive equipments were required to make and measure the samples. Pressure measurement using capillary rheometer was a very effective and easy method with high accuracy. Homogeneous feedstock increased the particle alignment of plastic magnet. Remanet flux density and maximum energy product increased linearly and quadratically with increasing particle alignment, respectively.

• Membrane Journal
• /
• v.11 no.4
• /
• pp.161-169
• /
• 2001

Single and mixed particle suspensions of kaolin, bentonite, starch and PMMA were carried out using a dead-end Amicon fi1tration cell with microfilteration membranes. The experimental data of permeate fluxes were fitted by the constant pressure fi1tration models in order to investigate fouling steps. In 0.1 wt% mixed solution of equal amount of kaolin and starch, the permeation flux was about 30% lower than the average of each particle flux. However, the permeation flux for kaolin/PMMA mixed solution was about 10% higher than the average of each particle flux. In the cases of bentonite and PMMA or starch mired solution, the improvement effect on permeation flux was weaken than that of kaolin mixed solution. Also, the membrane fouling resistance for mixed particle solution of equal amount of kaolin and starch was minimum at 0.05 wt% particle concentration.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.5
• /
• pp.90-96
• /
• 2001

This paper proposes the hybrid fuzzy control system for fast response time and precision control of auto-equipment which exist disturbance, parameter alteration of system, uncertainty. The purposed system, which provides the improvement in terms of the control region in high speed and precision control, first used the fuzzy control method for fast response time and when the error reaches the preset value, used the frequency-locked method for precision control. The theoretical and experimental studies have been carried out. The presented results from the above investigation show considerably improved performance in the position control of auto-equipment.