Proceedings of the Korea Water Resources Association Conference
/
2019.05a
/
pp.203-203
/
2019
도시화로 인한 불투수면의 증가는 물순환 왜곡, 비점오염원 발생 및 수생태계 건상성 훼손 등을 야기시키며, 이를 해결하기 위하여 다양한 LID 기법을 적용하고 있다. 일반적으로 LID 내 적용 되는 여재들은 무기성여재로 중량이 크고 미세공극의 부재로 물리화학적 및 생물학적 저감기능이 제한적이다. 따라서 본 연구에서는 중량성이 낮은 생물폐자원을 선정하여 LID 시설 적용성평가를 수행하고자 한다. 생물폐자원은 발생량, 경량성 및 용이성을 고려하여 꼬막껍질(CS)과 호두껍질(WS)을 선정하였다. 생물폐자원의 산화부식을 고려하여 무기성 여재인 화산석과 혼합하여 Bioretention 시설에 적용하였으며, 여재 혼합비율에 따라 총 3가지의 Case 로 구성하였다. 식생은 구절초와 꽃댕강나무를 식재하였으며, 여재의 물리적 특성 분석을 위하여 적용 전과 후의 SEM(Scanning Electronic Microscope)을 수행하였다. 모니터링은 도로퇴적물 100g과 물 110L를 제조하여 인공강우유출수를 이용하여 수행하였으며, $0.0003{\sim}0.007m^3/sec$의 유속으로 주입하였다. 시설의 유입 및 유출부에서 유량 측정 및 수질 시료를 채취하였으며, 채취된 시료는 수질오염공정 시험법에 준하여 입자상 물질, 유기물, 영양물질 및 중금속 등을 분석하였다. Bioretention 시설의 모니터링 결과를 이용하여 물수지 및 TSS 저감 효율을 산정하였으며. 물수지 분석결과 시설의 저류율은 Case 1(soil) > Case 3(WS+RV) > Case 2(CS+RV) 순으로 나타났다. 시설 내 공극률이 가장 낮았던 Case 1에서 저류율이 약 55%로 가장 높게 것으로 분석되었다. Case 3(WS+RV)은 Case 2(WS+RV)와 시설 내 공극률이 유사함에도 불구하고 저류율이 약 10% 높은 것으로 분석되었다. 오염물질 저감효율 분석 결과, TSS와 TP의 제거효율은 모든 Case에서 약 75% 이상으로 높게 나타났으며, COD의 경우 모래를 적용한 Case 1에 비해 생물폐자원인 꼬막껍질과 호두껍질을 적용한 Case에서 약 1.3배 이상 높게 나타났다. 호두껍질과 꼬막껍질의 SEM 분석 결과 표면에 다공성이 형성되어 있는 것으로 조사되었다. 이는 여과 및 저류기작으로 인한 물순환 효과증대와 다공성과 돌기사이로 인한 입자상의 물질 여과 및 흡착으로 인하여 오염물질의 제거효율이 증대 된 것으로 평가된다. LID시설 내 생물폐자원과 무기성여재를 적절히 배합하여 복합여재로 조성할 경우 침하현상을 방지할 뿐만 아니라 저류 및 침투기능 향상과 미생물의 서식환경을 제공하기에 물순환 회복 및 비점오염물질 저감에 기여할 것으로 평가된다.
Chae, Yeon-Hwa;Moon, Heung Soo;Kim, Seyoung;Woo, Sang Kuk;Park, Ji-Yeon;Lee, Kee Sung
Composites Research
/
v.30
no.2
/
pp.84-93
/
2017
This study investigates thermal and mechanical characterization of environmental barrier coating on the $SiC_f-SiC$ composites. The spherical environmental barrier coating (EBC) powders are prepared using a spray drying process for flowing easily during coating process. The powders consisting of mullite and 12 wt% of Ytterbium silicate are air plasma sprayed on the Si bondcoat on the LSI SiC fiber reinforced SiC composite substrate for protecting the composites from oxidation and water vapor reaction. We vary the process parameter of spray distance during air plasma spray of powders, 100, 120 and 140 mm. After that, we performed the thermal durability tests by thermal annealing test at $1100^{\circ}C$ for 100hr and thermal shock test from $1200^{\circ}C$ for 3000 cycles. As a result, the interface delamination of EBC never occur during thermal durability tests while stable cracks are prominent on the coating layer. The crack density and crack length depend on the spray distance during coating. The post indentation test indicates thermal tests influence on the indentation load-displacement mechanical behavior.
In order to use a polysaccharide, curdlan, as a concrete admixture, we first developed a pilot-scale fermentation process for the mass production of curdlan. We also examined the rheological properties of curdlan, and tested how well the curdlan obtained in this work increased the segregational resistance of the cement slurry. Fermentation was performed in a 300-liter fermenter equipped with 3 disk-turbine impellers. Since curdlan production is stimulated under nitrogen-limiting conditions, the culture pH was shifted from the optimal pH for cell growth (pH 7.0) to the optimal pH for curdlan production (pH 5.5) at the onset of ammonium exhaustion. We obtained a curdlan production of 65 g/L in 120 hr batch cultivation of Agrobacterium species. The insoluble curdlan at the final stage of fermentation was readily harvested by centrifugation together with the cells. The freeze-dried sample contained 78% (w/w) of curdlan. The solubility and viscosity of the curdlan increased with the increase of the solution pH, which enhances the viscosity of concrete since the pH of concrete is extremely high (pH 13.0). Test results of the curdlan as a concrete admixture with cement slurry demonstrated that it prohibits the leakage of water. In conclusion, this work certifies and enlarges curdlan's industrial potential as a concrete admixture.
Proceedings of the Korean Information Science Society Conference
/
2001.04a
/
pp.37-39
/
2001
반도체 설계는 급속한 기능 추가와 기가 헬쯔에 육박하는 고속 동작에 부응하는 제품의 설계와 빠른 출시를 위하여 다방면의 연구를 거듭하고 있다. 하지만, 인터넷과 정보 가전의 모바일 기기에서 요구하는 폭발적인 기능의 추가와 가전기기의 최소화를 위하여서는 그 요구를 감당하지 못하고 있다. 이를 위한 방안으로 설계 재활용과 System-On-Chip의 설계가 수년 전부터 대두되었으나 아직 큰 실효를 거두지 못하고 있다. SoC설계는 다기능을 한 칩에 구성하는 방법을 시도하고 있고, 설계 재활용은 기존의 설계(IP)를 다른 것과 혼합하여 필요한 기능을 제공하는 방법이 시도되고 있다. 이 두가지의 VLSI 설계 방식 흐름을 가능하도록 하기 위한 연구로써, 레이아웃 이식에 관한 연구를 진행하였다. IP 재활용을 위하여서는 다양한 공정변화에 신속히 대응하고, 기존의 설계 설계규칙으로 설계된 면을 현재의 공정인 0.25um, 0.18um 테크놀러지에 맞도록 변환하는 VLSI 소프트웨어 시스템을 필요로 한다. 레이아웃 설계도면을 분석하여 소자 및 배선을 인식하는 알고리즘을 연구와 개발하고, 도면을 첨단 테크놀러지의 설계 규칙에 부응하도록 타이밍, 소비 전력, 수율을 고려한 최적의 소자 및 배선의 크기를 조절하는 방법을 고안하며, 칩 면적을 최적화할 수 있는 컴팩션 알고리즘을 개발하여 레이아웃 설계 도면을 이식할 수 있는 자동화 소프트웨어 시스템을 연구하였다. 더불어, 현재 반도체 소프트웨어 시스템의 최대 문제점에 해당하는 처리 속도와 도면의 처리 능력을 비교, 검토하여 본 연구가 속도면에서 평균 27배 효율면에서 3배 이상의 상대우위를 점하였다.전송과 복원이 이루어질 것이다.하지 않은 경우 단어 인식률이 43.21%인 반면 표제어간 음운변화 현상을 반영한 1-Best 사전의 경우 48.99%, Multi 사전의 경우 50.19%로 인식률이 5~6%정도 향상되었음을 볼 수 있었고, 수작업에 의한 표준발음사전의 단어 인식률 45.90% 보다도 약 3~4% 좋은 성능을 보였다.으로서 hemicellulose구조가 polyuronic acid의 형태인 것으로 사료된다. 추출획분의 구성단당은 여러 곡물연구의 보고와 유사하게 glucose, arabinose, xylose 함량이 대체로 높게 나타났다. 점미가 수가용성분에서 goucose대비 용출함량이 고르게 나타나는 경향을 보였고 흑미는 알칼리가용분에서 glucose가 상당량(0.68%) 포함되고 있음을 보여주었고 arabinose(0.68%), xylose(0.05%)도 다른 종류에 비해서 다량 함유한 것으로 나타났다. 흑미는 총식이섬유 함량이 높고 pectic substances, hemicellulose, uronic acid 함량이 높아서 콜레스테롤 저하 등의 효과가 기대되며 고섬유식품으로서 조리 특성 연구가 필요한 것으로 사료된다.리하였다. 얻어진 소견(所見)은 다음과 같았다. 1. 모년령(母年齡), 임신회수(姙娠回數), 임신기간(姙娠其間), 출산시체중등(出産時體重等)의 제요인(諸要因)은 주산기사망(周産基死亡)에 대(對)하여 통계적(統計的)으로 유의(有意)한 영향을 미치고 있어 $25{\sim}29$세(歲)의 연령군에서, 2번째 임신과 2번째의 출산에서 그리고 만삭의 임신 기간에, 출산시체중(出産時體重) $
Journal of the Korea Academia-Industrial cooperation Society
/
v.20
no.12
/
pp.247-253
/
2019
3D printing technology has attracted considerable attention because of its potential to fabricate the intricate design of ceramic products. In this study, ceramic 3D nozzle printing was introduced to manufacture complex alumina products with a ceramic pigment. The alumina paste was formulated by incorporating an elastomer to impart viscoelastic properties. Viscoelastic pastes play an essential role in ceramic 3D nozzle printing. The effects of the viscoelastic properties of the ceramic pastes on their printability were assessed using comprehensive rheological analysis, and various shapes were printed. As a result, the paste with a high yield stress showed better printability. In addition, a ceramic pigment was added to the developed pastes to increase the aesthetics of the printed ceramic structure. The printed ceramic parts were sintered in air at 1300 ℃. The stability of the ceramic pigment was confirmed even after high-temperature sintering.
This paper presents a new framework for design and economic evaluation of wind energy-based electricity supply system. We propose a network optimization (mixed-integer linear programming) model to design the underlying energy supply system. In this model we include practical constraints such as land limitations of onshore wind farms and different costs of offshore wind farms to minimize the total annual cost. Based upon the model, we also analyze the sensitivity of the total annual cost on the change of key parameters such as available land for offshore wind farms, required area of a wind turbine and the unit price of wind turbines. We illustrate the applicability of the suggested model by applying to the problem of design of a wind turbines-based electricity supply problem in Jeju. As a result of this study, we identified the major cost-drivers and the regional cost distribution of the proposed system. We also comparatively analyzed the economic performance of on/off shore wind farms in wind energy-based electricity supply system of Jeju.
Kim, Sang-Woo;Park, Kyung-Min;Ha, Jae-Uk;Lee, Jae-Hwan;Chang, Pahn-Shick
Korean Journal of Food Science and Technology
/
v.41
no.2
/
pp.173-178
/
2009
Epidemiological studies showed that high trans-fat consumption is closely associated with getting the risks of cardiovascular disease. The objective of this study was to produce trans-free fat through lipase-catalyzed interesterification, as a substitute for the cream margarine commonly used in industry. Optimum conditions for interesterification in a packed bed enzyme bioreactor (PBEB) were determined using response surface methodology (RSM) based on central composite design. Three kinds of reaction variables were chosen, such as substrate flow rate (0.4-1.2 mL/min), reaction temperature (60-70$^{\circ}C$), and ratio of fully hydrogenated canola oil (FHCO, 35-45%) to evaluate their effects on the degree of interesterification. Optimum conditions from the standpoint of solid fat content (SFC) were found to be as follows: 0.4 mL/min flow rate, 64.7$^{\circ}C$ reaction temperate, and 42.8% (w/w) ratio of FHCO, respectively. The half-life of immobilized lipase in PBEB with two stages at 60$^{\circ}C$ ($1^{st}$ stage) and 55$^{\circ}C$ ($2^{nd}$ stage) was about more than 30 days as estimated by extrapolating the incubation time course of tristearoyl glycerol (TS) conversion, whereas the half-life of the enzyme in PBEB with single stage at 65$^{\circ}C$ was only about 15 days. Finally, the results from SFC analysis suggest that trans-free fat produced in this study seems to be a suitable substitute for the cream margarine commonly used in industry.
Kim, Jin-Seop;Kim, Jong-Bum;Kim, Jae-Ho;Lee, Na-Young;Jung, Sung-Hee
Journal of Radiation Protection and Research
/
v.33
no.1
/
pp.13-20
/
2008
The flow rate measurements in a multi-phase flow pipeline were evaluated quantitatively by means of a clamp-on sealed radioisotope based on a cross correlation signal processing technique. The flow rates were calculated by a determination of the transit time between two sealed gamma sources by using a cross correlation function following FFT filtering, then corrected with vapor fraction in the pipeline which was measured by the ${\gamma}$-ray attenuation method. The pipeline model was manufactured by acrylic resin(ID. 8 cm, L=3.5 m, t=10 mm), and the multi-phase flow patterns were realized by an injection of compressed $N_2$ gas. Two sealed gamma sources of $^{137}Cs$ (E=0.662 MeV, ${\Gamma}$$factor=0.326\;R{\cdot}h^{-1}{\cdot}m^2{\cdot}Ci^{-1}$) of 20 mCi and 17 mCi, and radiation detectors of $2"{\times}2"$ NaI(Tl) scintillation counter (Eberline, SP-3) were used for this study. Under the given conditions(the distance between two sources: 4D(D; inner diameter), N/S ratio: $0.12{\sim}0.15$, sampling time ${\Delta}t$: 4msec), the measured flow rates showed the maximum. relative error of 1.7 % when compared to the real ones through the vapor content corrections($6.1\;%{\sim}9.2\;%$). From a subsequent experiment, it was proven that the closer the distance between the two sealed sources is, the more precise the measured flow rates are. Provided additional studies related to the selection of radioisotopes their activity, and an optimization of the experimental geometry are carried out, it is anticipated that a radioisotope application for flow rate measurements can be used as an important tool for monitoring multi-phase facilities belonging to petrochemical and refinery industries and contributes economically in the light of maintenance and control of them.
An ore of stone obtained from quarry lose its about 60% such as the muck and the stone-dust during the process of making the architectural block, the crushed aggregate and so on. A part of the muck is only reutilized for the crushed aggregate as road pavement materials, while the most of the muck in the shape of powder is mixed with water and then it is deposited in a sludge tank. The muck in the shape of powder is called the stone-dust. If the stone-dust is discharged and sprayed, an ecosystem will have terrible damage because the seepage of surface water, the flow of ground water and the movement of air are not occurred smoothly by packing the void of soils. As the Waste Management Law (2003) in Korea, the stone-dust is sorted out the industrial waste and the most of that is dumped in ground. Therefore, the establishments of an efficient recycling plan are necessary through the improvement of engineering properties of the stone-dust. To investigate the possibility of recycle and improvement for the stone-dust, the stone-dust and natural soils are sampled from six quarries in Korea. The various soil tests are performed by use of the mixed soils with the stone-dust content ratio. As the result of various soil tests, the recycle possibility of the stone-dust is analyzed as subbase layer materials of the roads.
KSCE Journal of Civil and Environmental Engineering Research
/
v.36
no.6
/
pp.1101-1107
/
2016
As an increase in the amount of RAP, there are growing interests in recycling asphalt concrete. In case of using the RAP as recycled asphalt pavement, it tends to be quality deteriorate. Therefore, the amount of RAP using is advised to be limited or has to be used with rejuvenator. In this study, asphalt mixture containing WMRA was analyzed to be used up to 50% for the sake of convenience on the process. As the results of evaluation, there was no significant difference in case of using 30% of RAP in the test of Marshall stability. However, in case of WMRA using up to 50%, it was satisfied criteria by flow value at 34.7. Further, result of toughness test was found that the crack resistance showed 55% higher than using straight asphalt when using WMRA binder up to 50%. According to the results of directly comparing crack resistance through repeated direct tensile test, it was shown that the fatigue crack resistance of WMRA pavement was increased by 263%. Therefore, it was shown that WMRA binder was effective in recycling RAP because WMRA binder could increase the percentage of RAP using up to 50%.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.