• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.2
• /
• pp.345-353
• /
• 1987

An analysis is performed to study flow and heat transfer characteristics of mixed free and forced convection about a sphere. Nonsimilar boundary layer equations which are valid over the entire regime of mixed convection are derived in terms of the mixed convection parameter, Gr/Re$^{2}$, through a dimensional analysis. The transformed conservation equations are solved by a finite difference method for the whole range of mixed convection regime. Numerical results for fluids having the Prandtl number 0.7 and 7 are presented. As the mixed convection parameter increases, the local friction coefficient and local heat transfer coefficient increases as well. For small Prandtl number, the friction coefficient is larger, while for large Prandtl number, the heat transfer coefficient is larger. Natural convection effect on the forced flow is more sensitive for small Prandtl number fluid. Flow separation migrates rearward as an increase in the mixed convection parameter. For small Prandtl number, the buoyancy effect is relatively small so that the flow separation occurs earlier.

• Journal of the Korean Vacuum Society
• /
• v.10 no.3
• /
• pp.341-349
• /
• 2001

Numerical calculation has been performed to investigate the fluid flow, heat transfer and local mass fraction of chemical species in the MOCVD(metalorganic chemical vapor deposition) manufacturing process. The mixing of reactants (trimethylgallium with hydrogen gas and ammonia) was presented by the concentration of each reactant to predict the uniformity of film growth. Effects of inlet size, location, mass flow rate and susceptor/cold wall tilt angle on the concentration were reported. From the numerical calculation, the concentration of reactants could be qualitatively predicted by the Nusselt number(heat transfer) and the optimum mass flow rate, wall tilt angle and inlet condition were considered.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.6
• /
• pp.2083-2099
• /
• 1991

An experiment has been carried out to investigate the aerodynamic effect of surface roughness on the characteristics of the turbulent separation and reattaching flow downstream of a backward-facing step. The distributions of boundary layer parameters, forward-flow fraction and turbulent stresses in the region near the reattachment point are measured with a split film sensor. It is demonstrated that the streamwise distributions of the forward-flow fraction in the recirculation and reattachment regions are similar, independent of the roughness. The reattachment length is found to be only weakly affected by the roughness. It is also shown that the velocity profile on the rough surface approaches to that of the equilibrium turbulent boundary layer faster than that on the smooth surface in the redeveloping region after reattachment.

• Journal of Korea Water Resources Association
• /
• v.38 no.12 s.161
• /
• pp.1051-1060
• /
• 2005

The present study analyzes hydrologic utilization of optimal radar-derived rainfall by using semi-distributed TOPMODEL and evaluates the impacts of radar rainfall and model parametric uncertainty on a hydrologic model. Monte Carlo technique is used to produce the flow ensembles. The simulated flows from the corrected radar rainfalls with real-time bias adjustment scheme are well agreed to observed flows during 22-26 July 2003. It is shown that radar-derived rainfall is useful for simulating streamflow on a basin scale. These results are diagnose with which radar-rainfall Input and parametric uncertainty influence the character of the flow simulation uncertainty. The main conclusions for this uncertainty analysis are that the radar input uncertainty is less influent than the parametric one, and combined uncertainty with radar and Parametric input can be included the highest uncertainty on a streamflow simulation.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.04a
• /
• pp.4-4
• /
• 2000

일반적인 액체추진제 로켓엔진의 연소는 분사제트의 미립화, 액적의 증발, 기상 추진제의 혼합, 화학반응 등, 일련의 물리적 과정들로 이루어지고, 여기서 특성속도 효율은 크게 분사특성 및 연소의 두 단계에서 결정되게 된다. 액체추진제 로켓엔진에 사용되는 여러 분무형태 중, 동축형 분사기에서는 액상과 기상 제트의 운동량 차에 의해 미립화가 이루어지며, 분무 액적들의 전개와 더불어 분사기 출구를 포함한 전 영역에서 연소가 발생되므로 매우 복잡한 물리적 특성들을 포함하게 된다. 본 연구에서는 기상 연료-액상 산화제의 동축형 분무연소를 JANNAF의 방법을 사용하여 수식화 하였으며, 이를 바탕으로 분무특성과 연소성능 예측을 위한 프로그램을 작성, 분사조건에 의한 분무특성과 그에 따른 연소성능을 계산하였다. 연속, 운동량, 에너지 및 혼합비 방정식의 지배방정식들을 바탕으로 기상 유동을 수식화 하였으며, 별도로 액적의 소산 및 연소과정을 모사하기 위한 별도의 수식들이 추가되었고, 이 식들을 결합하여 액적의 크기, 분포를 포함하는 액체 제트의 미립화 정도를 공간적으로 계산하였다. 미립화 모델의 검증을 위하여 계산 결과를 Reitz의 실험과 Giridharan의 모델 등과 비교하였으며 잘 일치하는 경향을 나타내었다. 또한 동축형 분사기에서의 분무 특성을 예측하기 위해 액체 산소, 기체 수소를 추진제 조합으로 하는 동축형 분무 연소장에서의 제트 길이, 액적의 크기, 액체 제트의 속도를 계산하였다. 계산 결과 액체 제트의 접촉길이는 분사공의 지름이 증가할수록 웨버수가 증가되므로 짧아지는 것으로 관찰되었으며 액적의 크기도 분사공의 지름이 증가할수록 작아지는 경향을 나타내었다. 액체 제트의 속도는 처음에는 일정하게 유지되다가 운동량을 보존하기 위해 가스로부터 운동량을 받아 점차 가속되어지는 것으로 나타났다.본 규격은 키, 총장, 어깨길이, 등길이, 머리길이, 머리둘레, 진동둘레, 목둘레, 가슴둘레, 허리둘레, 배둘레, 엉덩이둘레, 앞품, 뒤품, drop치를 포함하고 있고, 각 규격에서 호칭간 치수 간격도 함께 제시하고 있다. 본 연구 결과에서 보듯, 현행 8규격의 무진복의 각 호칭간 적정 허용범위를 고려해 합리적인 치수체계를 정립한다면 치수에 대한 적합도가 상당히 증가할 뿐 아니라 생산비용도 상당히 감축할 것으로 생각된다.나타났다. 4) 호감적 서비스능력 차원에서 세 독립변수간에 유의한 3원 상호작용이 존재하는 것으로 나타나( $F_{2,228}$=15.62, P<.001) 20대에 적합한 의복 착용시( $F_{2,228}$=3.98, P<.05)와 60대에 적합한 의복 착용시( $F_{2,228}$=16.55, P<.001) 점포유형과 격식차림간에는 유의한 상호작용이 존재하는 것으로 나타났다. 5) 호감을 구성하는 세 요인들이 구매의도에 미치는 영향을 조사한 결과 호감적 인상차원은 29%(P<.001), 호감적 서비스능력차원은 6%(P<.001)의 구매의도를 설명해 주는 것으로 나타났다. 본 연구결과 노년 소비자에게 호감을 주는 판매원의 외모는 구매의도에 영향을 주어 실버의류산업의 이익증대와 밀접한 연관을 갖는 서비스품질의 중요한 요인으로 밝혀졌다.중요한 요인으로 밝혀졌다.로운 단백질 EPSPS가 다른 여러 식물에 이미 존재하고 있는 단백질로서 우리가 이미 이러한 식품을 섭취할 때 이 단백질도 같이 섭취해오고 있었다는 점, 둘째. 이 단백질이 소화액 분해 실험에서 짧은 시간내에 분해가 되었다는 점, 셋째. 재조합 된 콩과 자연 콩이 성분 분석에서 차이를 나타내지 않았다는 점, 네 번째. 쥐를 통한 다양섭취 실험에서 아무런 이상 반응이 없었

• Journal of the Korean association of regional geographers
• /
• v.18 no.3
• /
• pp.253-267
• /
• 2012

The study looked into the type and characteristics of debris landforms in Mt. Mudeung. By focusing on the representative area, we aimed to categorize the debris landforms based on the morphologic and genetic characteristcis. The types of debris areas in Mt. Mudeung can be divided into the exposed debris type, mixed type of matrix, and the boulder-hidden type. Supply of block in the debris slope area displays different features depending on types of rocks. For the stony slopes of andesite, the block must be moved from the columnar joint or cliff in the upper part. The andesite debris slopes display dominant edge shape while displaying no round shape. The granite stony slopes display dominant round shape and the present exposed slope was assumed to be formed as the core stone which was deep weathered moved along slope during the periglacial era and the matrix was removed after post-glacial era. The movements of blocks are assumed to be caused by solifluction process. The joint area where granite and andesite areas meet, granite is located beneath andesite area, and this implies that blocks were actively freezing and creeping by solifluction and freezing and thawing at that time. It can be assumes that the granite matrix formed plain slope and then andesite boulder covered up the slope. Currently, the blocks in the stony slopes of Mt. Mudeung shows almost no mobility and the stony slopes created under periglacial climate can be considered to be fossil landform.

• Journal of Oral Medicine and Pain
• /
• v.37 no.4
• /
• pp.233-242
• /
• 2012

The purposes of this study were to compare psychological profiles, to investigate the differences in the clinical characteristics, and to compare treatment outcomes between myogenous pain and arthrogenous pain subgroups of temporomandibular disorder (TMD) based on Research Diagnostic Criteria for Temporomandibular disorders (RDC/TMD). Two hundred and fifty two patients diagnosed as TMD were divided into three groups based on the RDC/TMD axis I diagnostic guidelines; myogenous pain group, arthrogenous pain group, and mixed pain (both myogenous pain and arthrogenous pain) group. RDC/TMD history questionnaire was administered to each patient and depression, somatization, jaw disability, pain intensity, disability days, and graded chronic pain scale were analyzed. Bruxism, clenching, insomnia, headache, and unilateral chewing were assessed in a standardized TMD dysfunction questionnaire and the duration of onset, chronicity of pain, treatment period, the effectiveness of the treatment, and improvement of symptoms also analyzed. Myogenous pain group had higher depression (p=0.002), and somatization scales (p<0.001) than the arthrogenous pain group. Mixed pain group showed higher pain intensity (p=0.008), disability days (p<0.001), graded chronic pain scale (p=0.005), somatization (p<0.001), and depression scores (p=0.002) than the arthrogenous pain group. Jaw disability did not show any significant differences among the three groups (p=0.058). Arthrogenous pain group reported more limitation of mouth opening than myogenous pain group (p=0.007). Duration of onset showed that the arthrogenous pain group had lowest prevalence of chronicity among three groups (p=0.002). Mixed pain group patients showed lowest symptom improvements among three groups (p=0.007). Multiple linear regression analysis results showed that the treatment effectiveness was significantly associated with somatization score (${\beta}$=-0.251, p=0.03).

• Ecology and Resilient Infrastructure
• /
• v.10 no.3
• /
• pp.64-72
• /
• 2023

Biopolymer is a versatile material used in food processing, medicine, construction, and soil reinforcement. 𝛽-glucan is one of the biopolymers that improves the soil water content and ion adsorption in a drought or toxic metal contaminated land for plant survival. We analyzed drought stress damage reduction in sweet potatoes (Ipomoea batatas L. cv. Sodammi) by measuring the growth and major protein expression and activity under 𝛽-glucan soil amendment. The result showed that sweet potato leaf length and width were not affected by drought stress for 14 days, but sweet potatoes grown in 𝛽-glucan-amended soil showed an effect in preventing wilting caused by drought in phenotypic changes. Under drought stress, sweet potato leaves did not show any changes in electrolyte leakage, but the relative water content was higher in sweet potatoes grown in 𝛽-glucan-amended soil than in normal soil. 𝛽-glucan soil amendment increased the expression of plasma membrane (PM) H⁺-ATPase, but it decreased the aquaporin PIP2 (plasma membrane intrinsic protein 2) in sweet potatoes under drought stress. Moreover, water maintenance affected the PM H⁺-ATPase activity, which contributed to tolerance under drought stress. These results indicate that 𝛽-glucan soil amendment improves the soil water content during drought and affects the water supply in sweet potatoes. Consequently, 𝛽-glucan is a potential material for maintaining soil water contents, and analysis of the major PM proteins is one of the indicators for evaluating the biopolymer effect on plant survival under drought stress.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.3
• /
• pp.9-19
• /
• 2015

Experimental research on characteristics of particle-laden jet by using a coaxial injector was conducted in order to design fuel and oxidizer injectors of the supercavitation underwater vehicle. $1{\mu}m$ and $42{\mu}m$ particles was simultaneously injected to obtain particle and fluid velocity. Small particles($1{\mu}m$) and large particles represent fluid and fuel characteristics respectively. Small particles, which was processed using PIV algorithms, and one for the large particles processed using PTV algorithms. Fluid phase axial velocity increases according to particle loading ratio increases, and particles are located at the outside of the high vorticity region in a mixing layer of a coaxial injector.

• Restorative Dentistry and Endodontics
• /
• v.33 no.1
• /
• pp.28-38
• /
• 2008

This study was to investigate the influence of composite resins with different elastic modulus, cavity modification and occlusal loading condition on the stress distribution of restored notch-shaped noncarious cervical lesion using 3-dimensional (3D) finite element (FE) analysis. The extracted maxillary second premolar was scanned serially with Micro-CT. The 3D images were processed by 3D-DOCTOR. ANSYS was used to mesh and analyze 3D FE model. A notch-shaped cavity and a modified cavity with a rounded apex were modeled. Unmodified and modified cavities were filled with hybrid or flowable resin. After restoration, a static load of 500N was applied in a point-load condition at buccal cusp and palatal cusp. The stress data were analyzed using analysis of principal stress. The results were as follows: 1. In the unrestored cavity, the stresses were highly concentrated at mesial CEJ and lesion apex and the peak stress was observed at the mesial point angle under both loading conditions. 2. After restoration of the cavity, stresses were significantly reduced at the lesion apex, however cervical cavosurface margin, stresses were more increased than before restoration under both loading conditions. 3. When restoring the notch-shaped lesion, material with high elastic modulus worked well at the lesion apex and material with low elastic modulus worked well at the cervical cavosurface margin. 4. Cavity modification the rounding apex did not reduce compressive stress, but tensile stress was reduced.