• The Journal of Engineering Geology
• /
• v.28 no.4
• /
• pp.605-618
• /
• 2018

Korea follows the slope design criteria during construction. It was enacted by the Ministry of Land, Transport and Maritime Affairs. There are cases where the Soil-nail is designed as a measure to secure slope stability. The arrangement of the soil-nail may be arranged at equal intervals or may be arranged differently depending on the soil failure model. The optimum design of the countermeasure method is determined by securing stability of the slope through optimization of dimensions and shape. However, when uniform nails are placed at low elevations in slopes, the standard safety factor is exceeded, which may hinder economic design. It is preferable to arrange the reinforcement of the nails over the entire slope. When the horizontal spacing of the nails was topology optimized according to the slope height, it was possible to minimize the amount of reinforcement while satisfying the standard safety factor. Since the active load is reduced in the section where the slope height is lowered, the safety factor after reinforcement may be excessively increased. Therefore, the phase optimization method is proposed as an economical optimal design method using the reinforcing shape density. In addition, a relational expression was designed to optimize the horizontal spacing by slope height.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1566-1567
• /
• 2011

일반적으로 배전반과 변압기와 같은 고전압 전력기기를 운전하는 경우에는 외부 환경에 의한 열화특성뿐만 아니라 전력기기 내부의 구조적 특성에 의한 절연적 특성 변화가 발생하게 된다. 따라서 고신뢰성의 고전압 전력기기를 설계하기 위해서는 이와 같은 점을 고려한 내부 설계가 이루어져야 한다. 본 연구에서는 접지부에 여러 가지 형상을 가지는 볼트와 같은 구조물을 위치시키고 그에 따른 절연파괴전압의 변화에 대한 연구를 수행하였다. 동일한 전극 간격에 대한 AC 전압의 특성변화를 실험을 통하여 측정하고 분석하였다. 실험 결과, 절연파괴전압은 접지측에 위치한 볼트의 형상에 따라 크게 변화한다는 사실을 알 수 있었으며, 이와 같은 결과는 고전압 전력기기를 설계 및 제작하는데 큰 도움이 될 수 있을 것으로 판단된다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.10a
• /
• pp.28-28
• /
• 1998

단일 충돌제트의 경우 충돌면에서의 열전달 효과는 제트 출구와 충돌면 사이의 간격, 노즐 형상에 따른 제트출구의 초기조건, Re$_{D}$수 변화와 충돌면의 형상이나 표면거칠기 등에 따라 변화하게 된다. 그러나 수직 충돌제트의 경우 정체영역에서의 국소적인 열전달 향상은 용이하나 반경 방향으로 열전달이 점차 감소하게 된다. 따라서 충돌면의 전반적인 열전달 향상을 위해서는 열전달이 정체점보다 상대적으로 낮은 영역에서 열전달 향상이 필요하다. 또한, 실제 적용시 충돌면의 형상이나 협소한 공간에서 노즐위치의 제약으로 인하여 충돌제트가 수직으로 분사되는 경우보다 경사진 제트가 더욱 많이 응용된다. 더욱이, 수직충돌제트가 사용되는 많은 상황에서도 주위의 다른 공기 흐름의 영향으로 인하여 실제 제트가 경사각을 갖고 분사되어진다 이러한 경사충돌제트의 중요성에도 불구하고 경사충돌제트에 대한 연구는 수직충돌제트에 대한 연구보다 상대적으로 적게 이루어져 왔다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.2
• /
• pp.445-450
• /
• 2016

This paper studied on the influence of naval vessel shape on vertical magnetic field after the vessel was demagnetized. The triangular shape, the rectangular shape and circular shape were adaped from vessel's structual drawings. Magneto-static FEM analysis was performed to obtain the iduced magnetic field due to earth magnetic field for those shapes. During demagnetization process, magnetic field of residual magnetization was observed. The holizontal and vertical magnetic field were calculated depending on vertical bias magnetic field through magnetc component seperation. To demagnetize naval vessel ship, demagnetizing coils shoud be wound more finely in the vow and stern of the ship than it should be in the mid-part of the ship.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.42 no.6
• /
• pp.67-76
• /
• 2005

This paper proposes a compact-sized surface myoelectric sensor for the myoelectric hand prosthesis. To fit the surface myoelectric sensor in the socket for the myoelectric hand prosthesis, the sensor should be a compact size. The surface myoelectric sensor is. composed of a skin interface and a single processing circuit that are mounted on a single package. The skin interface has one reference and two input electrodes, and the reference electrode is located in the center of two input electrodes. In this paper we propose two types of sensors with the circle- and bar-shaped reference electrode, but all input electrodes are the bar-shaped. The metal material of the electrodes is the stainless steel (SUS440) that endures sweat and wet conditions. Considering the conduction velocity and the median frequency of the myoelectric signal, we select the inter-electrode distance (IED) between two input electrodes as 18mm, 20mm, and 22 mm. The signal processing circuit consists of a differential amplifier with a band pass filter, a band rejection filter for rejecting 60Hz power-line noise, amplifiers, and a mean absolute value circuit. We evaluate the proposed sensor from the output characteristics according to the IED and the shape of the reference electrode. From the experimental results we show the surface myoelectric sensor with the 18mm IED and the bar-shaped reference electrode is suitable for the myoelectric hand prosthesis.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.4
• /
• pp.35-42
• /
• 2015

This study analytically reviewed the behavior of Steel Plate Concrete(SC) walls subjected to cyclic loads to investigate the effects of shape and arrangement spacing of studs on the behavior of SC walls. To perform it, 9 cases of finite element analyses considering the different shape and spacing of studs in SC wall were carried out. As the results, the skeleton curves were obtained from the load-displacement history curves and the ultimate and yielding forces were increased as the spacing of studs decrease. In addition, the strength of inclined studs are shown to be bigger compared to that of general studs. The damping ratios are increased as the decrease of strength ratio. Finally, as the decrease of stud spacings, the cumulative dissipated energy was increased and the seismic performance was improved.

• Journal of Korea Water Resources Association
• /
• v.52 no.4
• /
• pp.255-264
• /
• 2019

The trapezoidal ribs had been installed in the retaining wall in order to reduce to flood damage in the impingement of mountain rivers. In this study, experiments in open channel with the trapezoidal ribs on sidewall were conducted to evaluate the effect of flow resistance by the trapezoidal shape. The hydraulic flow characteristics according to the flow rates were surveyed where the wall roughness is k-type that dimensionless spacings, ${\lambda}_{nv}$, are 6, 9, and 12. The flow-resistance factors such as roughness and friction coefficients increased generally with increase of the spacing of ribs. In high flow rate the friction coefficient showed the maximum value when ${\lambda}_{nv}$ is 9. Though the trapezoidal ribs has the relatively smaller flow resistance compared to the square ribs, their form drag accounted for mean 62% of the total flow resistance. It was confirmed that the optimal spacing of trapezoidal ribs to maximize the effect of flow resistance as the wall roughness increases are 9 to 12 times of the height of trapezoidal ribs.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.1
• /
• pp.1-8
• /
• 2014

Two-dimensional laminar numerical analyses were carried out for investigating the thermo-hydraulic characteristics of wavy channels with different shape parameters ($0.5{\leq}{\in}{\leq}1.5$, $0.1{\leq}{\gamma}{\leq}0.4$). PAO (polyalphaolefin), which is used for electronics cooling, is considered as the working fluid. In addition, constant properties, periodically developed flow, and uniform channel wall temperature conditions are assumed. Streamline and temperature fields, isothermal Fanning friction factors, and Colburn factors are presented for different Reynolds numbers in the laminar region ($1{\leq}Re{\leq}1000$). The results show that heat transfer is enhanced when the channel corrugation ratio (${\gamma}$) is large and channel spacing ratio (${\in}$) is small in the low Reynolds number region (Re < 50) and when ${\in}$ and ${\gamma}$ are large in the high Reynolds number region ($Re{\geq}50$).

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.11
• /
• pp.971-978
• /
• 2016

Recent trends in miniaturization and lightness in portable electronics parts have driven developments in subminiature screws. This study aims to investigate the thread rolling process of a subminiature screw with an outer diameter and pitch of 1.0 and 0.25 mm, respectively. Finite element (FE) analyses were performed for the thread rolling process of symmetric and asymmetric screw threads. Through FE analyses, various process parameters, such as the horizontal and vertical die gap and the rolling stroke, were investigated in terms of the forming accuracy. The material flow characteristics in the thread rolling process of the symmetric and asymmetric screws were also discussed, and the relevant process parameters were determined accordingly. These simulation results were then reflected on real thread rolling processes, from which the symmetric and asymmetric screws could be formed successfully with allowable dimensional accuracy.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.11
• /
• pp.1125-1130
• /
• 2017

The tooth shapes of serration-type and spline-type reactors are optimized using finite element methods to improve the working life of the part and to lower the stress concentration during rotation resulting from contact with the outer race for a reactor operating with $170^{\circ}C$ transmission oil. The results of thermal expansion analyses between an Al reactor and the steel outer race indicate that, before optimization, the gap between the two parts increases further as the serration-type reactor expands by 0.1 mm and the spline-type one strains by 0.08 mm. Because of shape optimization, a trapezoidal shape is obtained from the initial triangular serration and the rectangular spline of the two reactors. The maximum von Mises stress of the serration-type convertor decreased by 24.5 ％, and by 9.3 ％ for the spline-type convertor. In addition, there is a 13 ％ reduction in the axial thickness, as compared to the initially designed model.