• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.5
• /
• pp.69-76
• /
• 2020

Global warming is a very important problem as it causes rapid climate change and natural disasters. Therefore, researches related to renewable energy are being actively conducted while promoting policies such as reducing carbon dioxide emission and increasing the proportion of renewable energy. Solar power generation is being applied in urban areas like BIPV as well as existing idle areas outside the city. Therefore, in this study, precast concrete blocks developed for paving roadways capable of solar power generation were designed and constructed. For the evaluation of field applicability for 6 months, skid resistance and block settlement were measured. As a result of the experiment, it was found that skid resistance satisfies the standard of general roadway in Korea, but not the standard of highway. The skid resistance tended to decrease as time passed. In addition, the settlement of the block gradually increased slightly, but it is much smaller than the allowable settlement of the roadway. Therefore, it is necessary to establish a maintenance period and method based on the periodic measurement results in the future.

• The Journal of Engineering Geology
• /
• v.31 no.2
• /
• pp.187-197
• /
• 2021

Clay mineral content of weathered zone is a key parameter for landslide studies. Electrical resistivity tomography is usually performed to delineate the geometry of complex landslides and to identify the sliding surface. In clay-bearing weathered zone, parallel resistivity Archie equation is employed to investigate the effect of conductivity added (resistivity reduced) by clay minerals of kaolinite and montmorillonite, which is dependent on their specific surface area and cation exchange capacities (CEC). A decrease of overall resistivity and apparent formation factor is observed with increasing pore-water resistivity, significantly in montmorillonite. Formation factor is found decreased with increasing porosity and decreasing cementation factor. Parallel Archie equation was applied to the electrical resistivity data from the test area (Sinjindo-ri, Taean-gun, Chungcheongnam-do, Korea) which experienced land creeping in the year of 2014. A panel test with varying clay-mineral contents provides the best fit section when the theoretical section constructed with the assumed contents approaches the field section, from which the clay-mineral content of the weathered zone is estimated to be approximately 10%. Resistivity interpretation schemes including the clay mineral contents for land creeping studies explored in this paper can be challenged more when porosity, saturation, and pore-water resistivity are provided and they are included in the numerical resistivity modeling.

• Analytical Science and Technology
• /
• v.34 no.6
• /
• pp.251-258
• /
• 2021

Knives are most frequently used as weapons in violent crimes. Criminals leave behind knife sheaths made of paper and tape at crime scenes. It is difficult to develop fingerprints using tape attached to a porous surface, resulting in the need to explore effective techniques for identifying fingerprints as well as the distribution of fingerprints on each surface, when evidence such as paper knife sheaths are found. In this study, 50 knife sheaths were prepared. The cyanoacrylate fuming (CA fuming) method was applied to develop fingerprints on the non-adhesive side of the tape, and a dual-purpose 1,2-indanedione/Zn (1,2-IND/Zn) reagent was used to separate tape from paper while simultaneously developing fingerprints on the paper. The fingerprints on the adhesive side of the tape were developed using Wet Powder Black^®. Using the R statistical analysis program (The R Foundation for Statistical Computing), we used a heat map to indicate the location of fingerprints developed from each surface. More fingerprints were detected at the ends than in the center of the adhesive side of the tape, and although the non-adhesive sides of tape and paper did not present clear distribution patterns, many fingerprints were developed that had sufficient clarity for personal identification. The results of this study may be applicable for processing evidence when paper sheaths are found at crime scenes.

• Journal of the Institute of Convergence Signal Processing
• /
• v.22 no.4
• /
• pp.179-184
• /
• 2021

Along with the development of the fourth industry, the public sector has increasingly paid more attention to search using drones and real-time monitoring, for various goals. The drones are used and researched to complete a variety of searching and monitoring missions, including search for missing persons, security, coastal patrol and monitoring, speed enforcement, highway and urban traffic monitoring, fire and wildfire monitoring, monitoring of illegal fishing in reservoirs and protest rally monitoring. Police stations, fire departments and military authorities, however, concentrate on the hardware part, so there are little research on efficient communication systems for the real-time monitoring of data collected from high-performance resolution and infrared thermal imagining cameras, and analysis programs suitable for special missions. In order to increase the efficiency of drones with the searching mission, this paper, therefore, attempts to propose an image analysis technique to increase the precision of search by producing image data suitable for searching missions, based on images obtained from drones and provide the foundation for improving relevant policies and establishing proper platforms, based on actual field cases and experiments.

• Korean Journal of Remote Sensing
• /
• v.38 no.6_1
• /
• pp.1423-1444
• /
• 2022

In this study, the sensitivity of the mid-infrared radiance to atmospheric and surface factors was analyzed using the radiative transfer model, MODerate resolution atmospheric TRANsmission (MODTRAN6)'s simulation data. The possibility of retrieving the land surface temperature (LST) using only the mid-infrared bands at night was evaluated. Based on the sensitivity results, the LST retrieval algorithm that reflects various factors for night was developed, and the level of the LST retrieval algorithm was evaluated using reference LST and observed LST. Sensitivity experiments were conducted on the atmospheric profiles, carbon dioxide, ozone, diurnal variation of LST, land surface emissivity (LSE), and satellite viewing zenith angle (VZA), which mainly affect satellite remote sensing. To evaluate the possibility of using split-window method, the mid-infrared wavelength was divided into two bands based on the transmissivity. Regardless of the band, the top of atmosphere (TOA) temperature is most affected by atmospheric profile, and is affected in order of LSE, diurnal variation of LST, and satellite VZA. In all experiments, band 1, which corresponds to the atmospheric window, has lower sensitivity, whereas band 2, which includes ozone and water vapor absorption, has higher sensitivity. The evaluation results for the LST retrieval algorithm using prescribed LST showed that the correlation coefficient (CC), the bias and the root mean squared error (RMSE) is 0.999, 0.023K and 0.437K, respectively. Also, the validation with 26 in-situ observation data in 2021 showed that the CC, bias and RMSE is 0.993, 1.875K and 2.079K, respectively. The results of this study suggest that the LST can be retrieved using different characteristics of the two bands of mid-infrared to the atmospheric and surface conditions at night. Therefore, it is necessary to retrieve the LST using satellite data equipped with sensors in the mid-infrared bands.

• Geophysics and Geophysical Exploration
• /
• v.9 no.4
• /
• pp.271-278
• /
• 2006

Investigations of underground cavities are required to provide useful information for the reinforcement design and monitoring of the ground subsidence areas. It is, therefore, necessary to develop integrated geophysical techniques incorporating different geophysical methods in order to accurately image and to map underground cavities in the ground subsidence areas. In this study, we conducted geophysical investigations for development of integrated geophysical techniques to detect underground cavities at the field test site in the ground subsidence area, located at Yongweol-ri, Muan-eup, Muan-gun, Jeollanam-do. We examined the applicability of geophysical methods such as electrical resistivity, electromagnetic, and microgravity to cavity detection with the aid of borehole survey results. The underground cavities are widely present within the limestone bedrock overlain by the alluvial deposits in the test site where the ground subsidences have occurred in the past. The limestone cavities are mostly filled with groundwater or clays saturated with water in the site. The cavities, thus, have low electrical resistivity and density compared to the surrounding host bedrock. The results of the study have shown that the zones of low resistivity and density correspond to the zones of the cavities identified in the boreholes at the site, and that the geophysical methods used are very effective to detect the underground cavities. Furthermore, we could map the distribution of cavities more precisely with the study results incorporated from the various geophysical methods. It is also important to notice that the microgravity method, which has rarely used in Korea, is a very promising tool to detect underground cavities.

• Journal of dental hygiene science
• /
• v.6 no.4
• /
• pp.295-302
• /
• 2006

This study was conducted to study the effects of the TA Theory and the TA Program, an educational testing tool developed to improve functional communication skills for dental hygienists. The results taken from the experiment using the TA program has been verified by Examination Tool for Personnel Communication developed by Chung(2001). 44 in two experimental groups and 16 in control group took part in TA Program training sessions. The experimental Group I received TA technique training session for 12 hours per day in a period of three days and Group II for 6 hours per day in a period of two days. From this experiment, the following conclusion was obtained. The results are as follows: 1) As it can be seen from the results of the examination taken prior to the experiment, the subjects of the control group and experimental groups were homogenous in all categories including self-disclosure, awareness, evaluation and acceptance of feedback, self-expression, coping with feelings, clearness, avoidance, dominance, handling of differences, and perceived acceptance. 2) After the training of TA Program was completed on Group I and II, the examination results are as follows: Control Group (1.5158), Group I (1.8260) / Control Group (1.4684), Group II (1.9985). The results of Group I and II (1.7970 and 1.9985 respectively) therefore showed a meaningful difference. 3) From the results of the experiment it is shown that dental hygienists' communication skills improved after receiving the TA Program training. Therefore TA Program may be used as an effective tool for such purpose. 4) As it can be observed from the data, Group I and II showed difference in the degree of improvements. Therefore, there needs to be a further investigation on the effects of the difference in training period. 5) This program is not only limited to the education of dental hygienists but may be widely applied to various forms of education and teaching methods.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.164-164
• /
• 2017

스마트 돈사 환경의 복지 및 생산성 향상을 위하여 정량 분석법을 기반으로 한 모돈 관리의 중요성이 증가하고 있다. 모돈은 교배, 임신, 분만, 포유, 이유를 순환적 반복하여 이루어지는데 모돈의 관리는 돈사 농장의 생산성 및 경제성과 직결된다. 모돈 관리에 필요한 환경 및 계측정보를 획득하고 이 정보로부터 모돈의 개체관리를 극대화시키고 최적의 방안을 찾고자 지속적으로 계측이 가능한 모돈의 돈사 모니터링 시스템이 필요하다. 모돈의 행동특성 계측이 가능한 시스템이 필요한 이유는 모돈의 행동 특성(섭식 및 지제불량 등)에 상응하는 대사 불량, 질병 및 발정 징후 등을 조기에 발견할 수 있기 때문이다. 돈사 내에서 정지 상태로 판별이 되는 모돈의 지제상태(기립상태, 누운 상태, 앉은 상태)와 다르게 연속적인 움직임으로부터 판별되는 모돈의 섭식상태를 분석하기 위해서는 계측 시스템과 이를 분석해주는 시스템간의 시간적 차이를 최소화 할 수 있는 실시간 신호 처리 기술이 필수적이다. 모돈의 섭식을 정량적으로 지수화하기 위한 센서의 최소 SPS(sample per second)는 600 Hz($100Hz{\times}6$개)로서 최소 6개 ADC 채널과 최소 1,200 Hz 이상으로 샘플링 할 수 있는 마이크로 컨트롤러가 필요하다. 또한 16 비트의 분해능으로 1분 동안 연속 계측을 수행할 경우 필요한 정보량은 153,600 KByte ($1,200sample/s{\times}16bit/sample{\times}8Byte/bit$)으로 실시간 처리를 수행하기에 매우 큰 정보량이라 판단할 수 있다. 수행하고자 하는 정보처리 기법에 따라 다소 상이할 수 있으나, 1분을 주기로 모돈의 섭식 분석을 수행하고자 할 경우 최도 150 MByte의 정보량을 처리하기 위한 최소의 클럭수는 단순 대입의 경우 2.5 Mhz (clock/second) ($=1clock/Byte{\times}150MByte/60seconds$) 이며 덧셈(4 clock)의 경우 10 Mhz, 곱셈(16 clock)의 경우 40 Mhz의 클럭이 필요하다. 또한 정보의 저장 및 도시를 위해 필요한 부가적인 회로(LCD, SD메모리) 구동을 위해 필요한 클럭을 고려할 경우 추가적인 클럭이 필요하다. 이를 종합적으로 고려하여 120 Mhz ($= 40Mhz{\times}3$) 이상의 클럭이 필요하다고 판단할 수 있다. 또한 센서 계측 주기의 시간 분해능을 균등하게 유지하기 위해선 계측->도시->저장의 과정을 교차적으로 수행해야 한다. 이러한 과정을 거처 최종적으로 선정한 마이크로 프로세서는 ARM Cortex-M4이며 168 MHz로 연산 수행이 가능하여 목표하고자 하는 신호처리를 수행 할 수 있다. 현장 예비 실험을 통해 기대 성능을 만족하였으며, 시간 복잡도가 높은 연산을 대비하여 최적 시분할 스케쥴링 기법에 대한 보완이 필요하다고 판단되었다.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.171-171
• /
• 2017

전산유체역학(CFD: Computational Fluid Dynamics)를 이용한 스마트팜 환경 내부의 정밀 제어 연구가 진행 중이다. 시계열 데이터의 난해한 동적 해석을 극복하기위해, 비선형 모델링 기법의 일종인 인공신경망을 이용하는 방안을 고려하였다. 선행 연구를 통하여 환경 데이터의 비선형 모델링을 위한 Tensorflow활용 방법이 하드웨어 가속 기능을 바탕으로 월등한 성능을 보임을 확인하였다. 그럼에도 오프라인 일괄(Offline batch)처리 방식의 한계가 있는 인공신경망 모델링 기법과 현장 보급이 불가능한 고성능 하드웨어 연산 장치에 대한 대안 마련이 필요하다고 판단되었다. CFD 해석을 위한 Solver로 SU2(http://su2.stanford.edu)를 이용하였다. 운영 체제 및 컴파일러는 1) Mac OS X Sierra 10.12.2 Apple LLVM version 8.0.0 (clang-800.0.38), 2) Windows 10 x64: Intel C++ Compiler version 16.0, update 2, 3) Linux (Ubuntu 16.04 x64): g++ 5.4.0, 4) Clustered Linux (Ubuntu 16.04 x32): MPICC 3.3.a2를 선정하였다. 4번째 개발환경인 병렬 시스템의 경우 하드웨어 가속는 OpenCL(https://www.khronos.org/opencl/) 엔진을 이용하고 저전력 ARM 프로세서의 일종인 옥타코어 Samsung Exynos5422 칩을 장착한 ODROID-XU4(Hardkernel, AnYang, Korea) SBC(Single Board Computer)를 32식 병렬 구성하였다. 분산 컴퓨팅을 위한 환경은 Gbit 로컬 네트워크 기반 NFS(Network File System)과 MPICH(http://www.mpich.org/)로 구성하였다. 공간 분해능을 계측 주기보다 작게 분할할 경우 발생하는 미지의 바운더리 정보를 정의하기 위하여 3차원 Kriging Spatial Interpolation Method를 실험적으로 적용하였다. 한편 병렬 시스템 구성이 불가능한 1,2,3번 환경의 경우 내부적으로 이미 존재하는 멀티코어를 활용하고자 OpenMP(http://www.openmp.org/) 라이브러리를 활용하였다. 64비트 병렬 8코어로 동작하는 1,2,3번 운영환경의 경우 32비트 병렬 128코어로 동작하는 환경에 비하여 근소하게 2배 내외로 연산 속도가 빨랐다. 실시간 CFD 수행을 위한 분산 컴퓨팅 기술이 프로세서의 속도 및 운영체제의 정보 분배 능력에 따라 결정된다고 판단할 수 있었다. 이를 검증하기 위하여 4번 개발환경에서 운영체제를 64비트로 개선하여 5번째 환경을 구성하여 검증하였다. 상반되는 결과로 64비트 72코어로 동작하는 분산 컴퓨팅 환경에서 단일 프로세서 기반 멀티 코어(1,2,3번) 환경보다 보다 2.5배 내외 연산속도 향상이 있었다. ARM 프로세서용 64비트 운영체제의 완성도가 낮은 시점에서 추후 성공적인 실시간 CFD 모델링을 위한 지속적인 검토가 필요하다.

• Journal of Bio-Environment Control
• /
• v.6 no.4
• /
• pp.284-291
• /
• 1997

This study was conducted to evaluate the optimum hydroponic system and nutrient solution for shortening the early growth period and quality improvement of dendrobium ( Dendrobium Phalaenopsis) seedlings. Dendrobium seedlings with 3 to 4 leaves were transplanted in the deep flow technique(DFT) system, aeroponic system, and ebb and flow system with different concentration of balanced nutrient solutions recommended by the Japanese Horticultural Experiment Station. Growth characteristics of shoot and root were recorded and evaulated among treatments. For autumn cultivation, plant height was the longest at the DFT system with quarter concentration of nutrient solution, where aeroponic system with half concentration of nutrient solution. Aeroponic system stimulated the root growth but fresh weight was observed in the plots of DFT system. For spring cultivation, pH values increased up 7.5 at the DFT and aeroponic system, where EC values did not fluctuate regardless of cultural system. Ebb and flow system showed the best result in the growth of plant followed by BFT system and aeroponic system. Higher concentration of nutrient solution within this range of treatment was recommended for the growth promotion of leaf length and width in DFT system. In conclusion, growth responses differed depending on the cultural system, concentrations of nutrient solutions and duration of cltivation.