• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.12
• /
• pp.1097-1106
• /
• 2011

Unsteady numerical analysis was performed to simulate air-launched missiles from a complete helicopter in hover by using an unstructured overset mesh flow solver coupled with a module of six degree-of-freedom motion of equations. The unsteady computations have been performed to obtain flow fields around the complete helicopter including main rotor, tail rotor, and fuselage equipped with multiple missiles, and six-DOF simulation has been performed to predict the behavior of the air-launched missile. The effects of the launching position and the missile thrust on the trajectory of the missile were investigated as well as the aerodynamic interference of the air-launched missile under the unsteady downwash produced by main rotor.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.2
• /
• pp.103-110
• /
• 2022

Degradation of handling qualities(HQs) due to bad weather or mechanical failure can pose a fatal risk to pilots unfamiliar with such situation. In particular, icing is an important issue to consider as it is a frequent cause of accidents. Most of the previous research works focuses on aerodynamic performance changes due to icing and the corresponding icing modeling or methods to prevent icing, whereas the present work attempts to actively compensate for HQ degradation due to icing on a full-scale helicopter through flight control law design. To this end, the present work first demonstrates HQ degradation due to icing using CONDUIT software, and subsequently presents a robust control design via the RS-LQR(Robust Servomechanism Linear Quadratic Regulation) procedure to compensate for the HQ degradation. Simulation results show that the proposed robust control maintains Level 1 HQ in the presence of icing.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.6
• /
• pp.519-529
• /
• 2010

In the present study, unsteady calculations have been performed to simulate flows around a UH-60A full configuration including main rotor, fuselage, and tail rotor. A flow solver developed for helicopter aerodynamic analysis was used for the simulation of the complete helicopter in high-speed and low-speed forward flight. Unsteady vibratory loads on the main rotor blades were compared with flight test and other calculated data for the assessment of the present flow solver. Aerodynamic interaction of the three components of the helicopter was investigated by comparing with the results of main-rotor-alone, main rotor and fuselage, and tail-rotor-alone configurations. It was found that the existence of the fuselage has an effect on the normal force distribution of the main rotor by varying downwash distribution on the rotor disc, and tip vortices trailed from the main rotor strongly interact with the tail-rotor.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.9
• /
• pp.801-811
• /
• 2021

Lightning can deliver large amounts of energy to the aircraft in a short period of time, resulting in catastrophic consequence. In particular, lightning strikes accompanied by high temperature heat and current can damage aircraft surface and internal electronic equipment, seriously affecting flight safety. Lightning experiments to analyze this effect use a Component A waveform with a maximum current of 200 kA as specified in SAE ARP 5412B. However, the actual lightning occurs mostly below 35kA and lightning indirect tests are conducted by reducing waveforms to prevent damage to internal electronic equipment. In this study, we examine previous methods to plot the Component A reduced waveform and identify their limitations. We then propose a new method to plot the reduced waveform based on adjusting the correction factor of the aircraft lightning Component A waveform. Finally, the electromagnetic analysis software EMA3D was used to compare the internal induced current size reduction ratio of the internal cable harness of the EC-155B helicopter.

• Transactions of the KSME C: Technology and Education
• /
• v.3 no.3
• /
• pp.183-191
• /
• 2015

In this study, the finite element analysis was carried out to investigate dynamic characteristics of the AGF(Active Gurney Flap) which is under development for reducing vibration and noise of the helicopter rotor system. The Gurney flap is a kind of small flat plate, mounted normal to the lower surface of the airfoil near to the trailing edge. An electric motor, L-shaped linkages and flap parts were integrated into a rotor bade, and 3~5/rev control was given to the AGF to reduce the vibration in the fixed frame. Thus, an explicit time integration method was adopted to investigate the dynamic response of the AGF with considering both centrifugal force due to the rotor rotation and active control input, and it can be seen that the vertical displacement of the AGF was satisfied to meet the design requirement.