• 한국정밀공학회지
• /
• 제19권12호
• /
• pp.142-149
• /
• 2002

In this paper, the metal forming process is caused of rise of the unit cost of production in increase of the lead-time and cost because of manufacturing final product through a few the number of processes. Flow control complex forming is proposed to put into formulation in order to apply cold forging from conventional approximate similarity theory, and the forming loads of the real material(AISI 1008) can be calculated by put at the new similarity formula the load by plasticine model material experiment through hub clutch. In order to reduce lead-time and cost the technology is used to manufacture with lower die of this product. By the application synthetic resin as the raw material, it is have the merit such short lead-time, low cost, good surface finish etc., as compared with the machine work.

• 한국정밀공학회지
• /
• 제25권12호
• /
• pp.33-38
• /
• 2008

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 추계학술대회 논문집
• /
• pp.531-532
• /
• 2008

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.1383-1384
• /
• 2013

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.1385-1386
• /
• 2013

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.1313-1314
• /
• 2010

• 한국기계가공학회지
• /
• 제9권6호
• /
• pp.101-108
• /
• 2010

The drum clutch investigated in this study is formed in 5 forming steps, which are 1st deep drawing, 2nd deep drawing, restriking, embossing, and $Grob^{TM}$ processes. Dimensional accuracy of the final products greatly depends upon how much more accurate pre-form is manufactured in the previous forming processes before the $Grob^{TM}$ process. The deep drawing, restriking and embossing processes in which the pre-form is formed are very important and decisive steps. Thus in some cases, excessive strain by these operations causes dimensional inaccuracy and cracks initiated from the base and wall of the product. Process variables such as the punch shapes both of 1st and 2nd deep drawing, and punch angle were selected to evaluate the deformation characteristics. The optimum parameters were determined from forming simulations using commercial FEM codes, DEFORM and Tauchi method, specifically developed for metal forming simulation. Finally, experiments for the whole drum clutch forming processes were carried out to verify the optimized forming parameters and the analytical results.

• 한국산학기술학회논문지
• /
• 제20권9호
• /
• pp.517-524
• /
• 2019

오버드라이버 허브클러치는 자동차 6단 자동 변속기 미션에 장착되어 엔진의 여유출력을 이용해 연료사용을 절감시켜주는 부품이다. 본 연구에서는 오버드라이버 허브클러치 제품에 대해 피어싱 공정 중 펀치에 가해지는 하중 및 소재 처짐량을 최소화 하고자 한다. 공정 중 펀치의 하중과 처짐량에 영향을 줄 수 있는 다이 클리어런스(die clearance)와 전단각도(shear angle) 그리고 마찰계수(friction coefficient)를 설계 변수로 설정했다. 또한 펀치의 하중과 소재 처짐량에 대해 각 설계 변수들의 영향도를 확인하기 위해 민감도 분석(sensitivity analysis)을 진행했다. 그 결과 전단 각도, 마찰 계수, 다이 클리어런스 순으로 하중 및 처짐량에 대해 민감한 것으로 조사되었다. 이를 통해 펀치의 하중과 소재 처짐량을 목적함수로 설정하고, 반응표면법(Response Surface Method)을 통해 각 설계 변수들과 목적함수의 방정식을 도출했다. 이를 통해 설정된 설계 변수들의 최적 값을 도출해 유한요소해석에 적용한 결과 펀치의 하중 및 소재의 처짐량이 기존대비 22.14% 개선됐다.

• 한국정밀공학회지
• /
• 제19권6호
• /
• pp.86-95
• /
• 2002

This paper suggests the new technology to control metal flow in order to reduce the number of preforming and the machining for the cold forged product with complex geometry. This technology is the combined forming that consists of bulk and sheet forming with double action dies. To analyze the process, finite element simulation has been performed. The proposed technology is applied to hub model that is part of air conditioner clutch. The purpose of this study is to investigate the material now of hub through the relative-velocity control of punch and mandrel using the flow control forming technique.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.271-272
• /
• 2010