• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2017.11a
• /
• pp.112-114
• /
• 2017

선박의 대형화, 해상물류 생산성 및 환경보존의 중요성이 증대함에 따라 다양한 부문에서 eNavigation 서비스가 요구되고 있으며 변화하는 기술환경이 고려되어야 한다. 항해안전과 효율성, 환경 등 다양한 수요를 고려하여 신뢰할 수 있는 최신 수로측량정보를 확보해야 한다. 본 연구에서는 다양한 목적에 효과적인 eNavigation 서비스가 제공될 수 있도록 수로측량정보 활용방안을 제시하고자 한다.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.31 no.3
• /
• pp.129-145
• /
• 2019

For the design of composite breakwater as representative one of the coastal and harbor structures, it has been widely discussed by the researchers about the relation between the behavior of excess-pore-water pressure inside the rubble mound and seabed caused by the wave load and its structural failure. Recently, the researchers have tried to verify its relation through the numerical simulation technique. The above researches through numerical simulation have been mostly applied by the linear and nonlinear analytic methods, but there have been no researches through the numerical simulation by the strongly nonlinear mutiphase flow analytical method considering wave-breaking phenomena by VOF method and turbulence model by LES method yet. In the preceding research of this study, olaFlow model based on the mutiphase flow analytical method was applied to the nonlinear interaction analysis of regular wave-composite breakwater-seabed. Also, the same numerical techniques as preceding research are utilized for the analysis of irregular wave-composite breakwater-seabed in this study. Through this paper, it is investigated about the horizontal wave pressures, the time variations of excess-pore-water pressure and their frequency spectra, mean flow velocities, mean vorticities, mean turbulent kinetic energies and etc. around the caisson, rubble mound of the composite breakwater and seabed according to the changes of significant wave height and period. From these results, it was found that maximum nondimensional excess-pore water pressure, mean turbulent kinetic energy and mean vorticity come to be large equally on the horizontal plane in front of rubble mound, circulation of inflow around still water level and outflow around seabed is formed in front of rubble caisson.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.13 no.3
• /
• pp.168-177
• /
• 2008

Trafficablility of a miner and potential environmental impacts due to mining activities should be considered in the selection of a commercial manganese nodule mining site. These two factors can be evaluated comparatively with physical properties and shear strength of sea-bed sediments. For the qualitative comparison of potential minig sites in terms of these two factors, physical properties such as water contents, void ratios, porosities, and grain densities, and shear strengths of surface sediments were determined for the three potential manganese nodule mining sites(KR1, KR2, and KR5) in the Korean manganese nodule contract area, northeast Pacific. For the study, sediment samples were collected from 107 stations from 2004 to 2006. The physical properties of surface sediments showed more significant differences between northern(KR1, KR2) and southern(KR5) blocks than between northern blocks(KR1 vs. KR2). Water content, void ratio, and porosity of sediments from KR5 were relatively higher than those from KR1 and KR2. Grain density of sediments from KR5 was relatively lower than those from KR1 and KR2. Shear strengths of the top 10cm sediments were higher in KR1 and KR2, whereas those of the deeper part were highest in KR5 block. Generally, sediments of high water contents are less suspendible than those of the low water contents by benthic disturbances, thus less disturbance is expected in the sediments of high water content by mining activities. In terms of trafficability, the shear strength of sediment below 10 cm deep is more important than shallower part because miner will disturb at least top 10 cm interval of the surface sediments. Base on these results, we conclude that KR5 area will be the best site for commercial mining among three investigated sites in this study.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.14 no.3
• /
• pp.184-191
• /
• 2011

Preliminary design of a mooring system for a floating wave energy converter(WEC) is performed. A mooring line is designed to consist of two parts; the one is a chain in heavy weight laid on the seabed and linked to an anchor on the seabed and the other is a light weight chain suspended at a floater. A high weight chain laid on the seabed can contribute to mitigate dynamic energy propagated from top oscillation and decrease anchor weight and volume. Through a low weight chain suspended between a floater and seabed the WEC's function to produce energy from wave can be affected in minimum by the motion of a chain. The static and dynamic analyses for the designed mooring system were carried out to evaluate WEC system's safety. The present study shows that the designed gravity anchor moves horizontally due to the tension exerted on the anchor in the severe ocean environmental condition. The present mooring system should be redesigned to satisfy the safety requirements. The present study will be useful to predict the safety of the mooring system under ocean environment.

• The Journal of the Acoustical Society of Korea
• /
• v.40 no.4
• /
• pp.297-303
• /
• 2021

When sound waves propagate over long distances in shallow water, measured transmission loss is greater than predicted one using underwater acoustic model with the Rayleigh reflection model due to inhomogeneity of the bottom. Accordingly, the US Navy predicts sound wave propagation by applying the empirical formula-based High Frequency Bottom Loss (HFBL) model. In this study, the measurement and analysis of transmission loss was conducted using mid-frequency (2.3 kHz, 3 kHz) in the shallow water of the East Sea in summer. BELLHOP eigenray tracing output shows that only sound waves with lower grazing angle than the critical angle propagate long distances for several kilometers or more, and the difference between the predicted transmission loss based on the Rayleigh reflection model and the measured transmission loss tend to increase along the propagation range. By comparing the Rayleigh reflection model and the HFBL model at the high grazing angle region, the bottom province, the input value of the HFBL model, is estimated and BELLHOP transmission loss with HFBL model is compared to measured transmission loss. As a result, it agrees well with the measurements of transmission loss.

• The Journal of the Acoustical Society of Korea
• /
• v.22 no.7
• /
• pp.554-561
• /
• 2003

Results of the numerical simulation and experimental data analysis for identification of mode cutoff frequency and estimation of sound speed of seabed from the spectrum of acoustic signal received at fixed source-receiver range are presented. Model simulations for Pekeris waveguide show that the frequency-dependent propagation loss and interference pattern are closely related to mode cutoff frequencies and it could be possible to the identify them from the changes of interference pattern. The concept considered at numerical simulations is applied to signals acquired at sea test. Cutoff frequency and sound speed of seabed are estimated from the interference pattern of measured signal. Propagation loss predicted using the estimated sound speed of seabed as model input parameter shows similar estimation result compared to propagation loss derived from measured data.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.8
• /
• pp.1222-1229
• /
• 2010

Compared to conventional high resolution acoustic profiling, ultra high resolution shallow acoustic profiling using parametric echo sounder is limited in penetration, yet it provides resolution suitable for detailed seabed investigation in the shallow waters. The parametric sub-bottom profiler system provides not only the exact determination of water depth, but also the detailed information about sediment layers and sub-bottom structures. Possible applications include dredging project, search of buried pipeline, ship wrecks, and other artificial objects through the detailed mapping of thickness and structure of the upper sedimentary layers. In this study, contaminated sediments were discriminated by the correlation of ultra high resolution profiles with geologic data. In addition, the burial depth of the submarine cable was measured by the interpretation of acoustic anomalies in the profiles.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2008.10a
• /
• pp.79-84
• /
• 2008

Compared to conventional high resolution acoustic profiling, ultra high resolution shallow acoustic profiling is limited in penetration, yet it provides resolution suitable for detailed seabed investigation in the shallow waters. Possible applications include search of buried pipeline, ship wrecks, and other artificial objects through the detailed mapping of thickness and structure of the upper sedimentary layers. In this study, contaminated sediments were discriminated by the correlation of ultra high resolution profiles with geologic data. In addition, the burial depth of submarine cable was measured by the interpretation of acoustic anomalies in the profiles.

• Journal of Navigation and Port Research
• /
• v.27 no.1
• /
• pp.87-95
• /
• 2003

Submarine optical fiber cable construction consists of marine survey, PLGR(Pre Lay Grapnel Run), shore-end-work, laying the submarine optical cable. This PLGR is work to ease the cable lay safely in seabed, improve the performance of Plough and ROV (Remotely-Operated Vehicle) laying work, and protect laying equipment. This paper presents the design and implementation of real-time monitoring system for PLGR work in submarine optical fiber cable construction enterprise. In this paper, we designe overall real-time monitoring system. For this purpose, the modules such as serial multiport communication module, real-time processing module, environment configuration module, real-time graph and a printout modules are designed and implemented. For the validity evaluation of this paper, serial multi port communication module, data parsing, realtime graph output are implemented and tested.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.6
• /
• pp.419-426
• /
• 2016

Measurements of bottom loss as a function of grazing angle (in range of $9{\sim}14^{\circ}$) at a frequency range of 4 ~ 8 kHz were conducted on an experimental site off Geoje island in October 2015. Geoacoustic inversion of the surficial sediment thickness is performed using the arrival time difference between the surficial layer and the sub-bottom layer reflected signal. To invert the thickness of surficial sediment, we used the grain size of $8{\sim}10{\phi}$ obtained by KIGAM (Korea Institute of Geoscience and Mineral Resources). The thickness of the surficial sediment was estimated to be 4 ~ 7 m. Finally, this inversion result was compared with the geoacoustic observation conducted by the KIOST (Korea Institute of Ocean Science & Technology) using sub-bottom profiler.