• Applied Chemistry for Engineering
• /
• v.10 no.3
• /
• pp.415-418
• /
• 1999

The characteristics of VRLA (valve regulated Iead-acid) battery with the tubular positive plate and gel type electrolyte were examined as a function of active material filling density. The filling density of positive plate was 3.2 g/mL, 3.4 g/mL, and 3.6 g/mL, respectively. These VRLA batteries were cycled with 100% DOD (depth of discharge) at the $C_5/5$ rate, followed by IU-type recharge with $I_{max}=0.2C_{10}/10$ and a final voltage V=2.40 V/cell. The test was performed in a thermostatic room at $25{\pm}1^{\circ}C$. The result indicated that the initial capacity was independent of active material filling density, i.e., the highest initial capacity was 3.4 g/mL of filling density and the lowest was 3.6 g/mL. On aspect of the cycle-life performance of the VRLA battery, the filling density of 3.6 g/mL was similar to that of 3.4 g/mL in the positive plate, and both were higher than that of 3.2 g/mL. Water-loss and degradation of the VRLA battery were decreased according to an increase of the filling density in the positive plate. The optimum filling density of the active material was 3.4~3.6 g/mL.

• Korean Journal of Environmental Agriculture
• /
• v.18 no.3
• /
• pp.272-279
• /
• 1999

This study was conducted to evaluate possibility for composting by microorganisms in food waste itself. In the result of counting of microorgansm in food waste, the number of bacteria growing at $30^{\circ}C$ and $50^{\circ}C$ were counted $10^5-10^7CFU/g$ and $10^5-10^6\;CFU/g$ in the almost food waste, respectively. Amylase and protease producing microorgansim were counted $10^3-10^7\;CFU/g$ at $30^{\circ}C$ and $50^{\circ}C$. In the result of composting for 30 days, FW1 was reveal that $CO_2$gas production rate and degradation of organic matter were similar to FW2 but higher than that of FW3, FM1 and FM2. Also, In the cases of change of enzyme producing microorgansim during the composting, FW1 were counted $10^5-10^9\;CFU/g$ at $30^{\circ}C$, $50^{\circ}C$ and $60^{\circ}C$ of incubation temperature, while FM1, added to commercial microbial inoculator, were less than that of FM1. Consequently, It was suggested that FW1 was most suitable condition for composting by microorganisms in food waste and there was no need to use microbial inoculator for composting.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.7
• /
• pp.4047-4051
• /
• 2014

Modern apartment houses are constructed to be relatively airtight with a high heat insulation system to increase the energy efficiency. Such a system has a range of deleterious effects due to the insufficient ventilation. In this study, the ondol system, which is used as a heat source typical of winter in Korea, was set as the default system to evaluate the indoor heat environment according to the ventilation method, the factors of energy reduction by the ventilation system was analyzed. The experimental apparatus was used to simulate the ambient conditions for a certain constant temperature and humidity chamber. The experimental results showed that the supply water temperature higher air volume decreases with increasing supply air temperature in the following order: floor supply/exhaust > total heat exchange supply/exhaust > forced supply/exhaust. Through this study, the applicability of various ventilations could be examined.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.3
• /
• pp.1658-1663
• /
• 2015

To control the indoor humidity, humidifier is installed in an air handling unit. Up to now, foreign product made of glasswool has been widely used as a humidifying element. In this study, a new humidifying element made of cellulose and PET was tested, and the performance was compared with Glasdek element, which is made of glasswool. Mass transfer rates and pressure drops were measured from the element which was installed at the entrance of the suction-type wind tunnel. Results show that, $j_m$ and f factors of the new element are 33%~39% larger and 0%~51% smaller than those of Glasdek. Large water absorption capacity and the smoothness of the new element appear to be responsible for the large $j_m$ and small f factor. The mass transfer effectivenesses ($j_m/f^{1/3}$) of the new element are 36%~63% larger than those of Glasdek.

• Magazine of the Korea Concrete Institute
• /
• v.8 no.4
• /
• pp.141-148
• /
• 1996

The pulished works on Accelerated Curing Effect were generally performed around from 1960 to 1970th century for 18 to 24 hours - total curing periods. It is not possible to define the effect of temperature rise because those results were obtaine mainly by using the manually operated steam-curing tank. Thus, it may not be available to apply those data immediately on the domestic PC wall production line. The testing specimens were made from the standard mix proportion according to those of domestic PC factories to establish a basic data for the Accelerated Curing Effect. The experimental tests were conducted according to the conditions of each sub-curing periods. By comparing the results of compression tests on de-molded and 28-day water-curing specimens, we find that the most effective curing condition to obtain more than the required design strength after 28 day of water curing may be as follows: the presteaming period does not affect seriously and less than$30^{circ}C/hr$- the rate of temperature rise andless than $82^{circ}C$ - maximum temperature are necessary. It seems that post-curing procedure is very important factor to increase the effect of accelerated curing.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.139-139
• /
• 2017

최근 환경오염 문제로 인한 연비 규제 강화 속도가 빨라지고 있으며 이에 따른 연비 향상 기술이 크게 대두 되고 있다. 연비 향상 기술 중 경량화 방안소재로 알루미늄(Al), 마그네슘(Mg) 등의 비철금속을 주로 사용하고 있으며, 이중 알루미늄은 다른 경량화 금속소재보다 우수한 경쟁력을 가지고 있다. 하지만 경제적인 측면에서 철 대비 비용적인 어려움을 가지고 있고 용접성이 떨어지기 때문에, 자동차 부품의 일부만 알루미늄 소재를 선택하여 사용하고 있는 실정이며 알루미늄의 높은 이온화 경향으로 인해 기존 자동차 철강 소재와 접촉 시 쉽게 부식되는 단점을 가지고 있다. 이러한 문제점을 해결하기 위해서는 알루미늄의 금속원소를 첨가하는 연구가 지속적으로 개발 되고 있다. 알루미늄 합금에서 마그네슘의 첨가는 좋은 용접성과 내식성, 강도를 향상시킨다. 하지만 3%이상의 마그네슘 첨가는 입계에 ${\beta}(Al_xMg_y)$석출상이 석출되게 되며, 입계에 연속적으로 형성된 ${\beta}(Al_xMg_y)$석출상은 응력 부식 균열 (Stress corrsion cracking)과 입계 부식(Intergranular corrosion)을 야기하는 결과를 가져온다고 알려져 있다. 이 문제를 해결하기 위해 Al 5000계열 합금의 Zn의 첨가를 통해 ${\tau}(Al_xMg_yZn_z)$을 입계에 석출시켜서 입계에 ${\beta}(Al_xMg_y)$상의 석출을 방지함으로써 내식성을 향상시키거나 Al 5000계열 합금의 열처리를 통해 ${\beta}(Al_xMg_y)$석출상을 고용시킴으로써 응력부식균열의 발생을 억제하는 연구도 있다. 하지만 열처리 후 Polarization test를 이용한 내식성 연구는 잘 안 알려져 있다. 따라서 이번 연구에서는 Al5000계열의 주조한 합금을 DSC분석을 통하여 ${\beta}(Al_xMg_y)$석출상의 고용 온도가 약 $470^{\circ}C$라는 것을 확인한 후, 실온에서 $100^{\circ}C/hr$으로 가열하고 조건에 따라 $450^{\circ}C$에서 3시간, 6시간, 12시간, 24시간, 30시간 항온 유지시킨 후 공냉을 진행하였다. 열처리를 마친 시편은 에폭시를 이용하여 마운팅 하였으며, 시편표면을 2000#까지 연마 후 증류수로 세척한 다음 질소를 이용하여 건조 후 분극 시험을 진행하였다. 3.5wt% NaCl 용액에서 분극 곡선을 통해 부식거동을 확인한 결과 24시간까지 시간이 증가 할수록 내식성이 우수해지는 것을 확인하였으며, 추가적으로 조직사진, SEM & EDS 분석과 XRD, TEM 분석을 통해 내식성은 입계에 존재하는 Mg의 조성이 감소하게 되면 내식성이 향상되는 것을 관찰하였다.

• Journal of Korean Society of Forest Science
• /
• v.63 no.1
• /
• pp.9-11
• /
• 1984

This study was carried out to compare the seed germination and seedling growth of Fraxinus mandshurica growing in natural forests of the interior of Korea. Three stimulation methods were used for germination and the seedlings were planted with various densities. The results obtained were summarized as follows: 1) It was suggested that the 80 seedlings per square meter were proper densities for their growth at a nursery bed. 2) Among the three stimulation methods, 19.9% of germination was shown by the moisture storage, 2.3% by cold and warm stratification, and 0.4% by cold stratification. 3) The 8.1% of the total seedlings showed secondary height growth.

• International Journal of Highway Engineering
• /
• v.14 no.1
• /
• pp.45-53
• /
• 2012

This study was performed to analyze test results on drying shrinkage for concrete specimens mixed with various constituents in concrete mixes. Test variables are coarse aggregate types(Limestone, Sandstone, Granite, Andesite, Gneiss), fine aggregate types(natural sand, crushed sand) and cement amounts(normal strength, high strength). Epoxy coating of(U&V-H(A,B)) was applied onto the specimen surface to simulate diverse volume surface ratios(22.2, 40, 85.7, 150, 200, 300) with different specimen sizes. The experiments had been executed during 1,014 days at a condition of $20^{\circ}C$ and relative humidity of 60% in environmental chambers. Test results showed that shrinkage strain from the specimen equivalent to real pavement decreased to 39% compared to the standard specimen recommended by KS. Test results also showed that shrinkage strain of the specimen mixed with Limestone was 56~76% of that with Sandstone, thus Limestone mix seems to be suitable to the concrete pavement.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.4
• /
• pp.13-18
• /
• 2016

Humidifiers are used to control indoor humidity. Element-type humidifiers have the advantages of simple structure and low energy consumption, and Japanese products have been widely used for the humidifying elements. In this study, a new humidifying element made of cellulose and PET was developed, and the performance was compared with that of a Japanese element. The mass transfer rates and pressure drops were measured for an element installed at the entrance of a suction-type wind tunnel. The humidification efficiency of the new element was 2 to 4% greater and the pressure drop was 23 to 32% smaller compared to the Japanese element. The mass transfer effectiveness ($j_m/f$) of the new element is also 5 to 28% higher. However, the water absorption capacity was smaller than that of the Japanese element, meaning further development is needed.

• Korean journal of applied entomology
• /
• v.37 no.2
• /
• pp.127-135
• /
• 1998

To study overwintering biology of the oriental tobacco budworm (OTB), Helicoverpaa.ssulta, OTB larvae were collected from middle and southern region of Korea in the autumn and rearedto diapausing pupae. Diapausing pupae were held at two different locations (Suwon and Chinju) and wererecollected in the spring to observe adult emergence rate and duration to adult emergence at 25$^{\circ}$C. Thesurvivorship of overwintering pupae was less than 5% when the pupae were buried in the soil in 20cmdepth. However, more than 60% of the pupae survived when they were kept in the plastic cup withartificial diet and were buried in the soil. The mean developmental periods of overwintering pupae at 25"C varied from 20.4 days to 43.9 days depending on years and locations where larvae were collected andpupae were held. The proportion of individuals which required longer than 30 days for development washigher in the population from the middle regions than those of southern regions. However, the proportiondecreased when the pupae collected from middle regions were held at Chinju, southern region. Chinju, southern region.