• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.3B
• /
• pp.315-324
• /
• 2010

We developed a design chart for very large floating structures through intensive hydroelastic analysis. Using this chart, one can predict the hydroelastic response of very large floating structures preliminarily at design stage without the cost-demanding hydroelastic analysis. This paper presents two new design charts based on the theory of VLFS. The purpose of the first design chart is to determine RAOs of the maximum longitudinal stress of VLFS considering properties of waves and structures. The design chart I can be applied to any sizes of VLFS in same aspect ratios and dimensionless stiffness parameters. The second design chart is developed to take into account the actual wave condition by using the Bretschneider spectrum with Beaufort sea state.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.4
• /
• pp.10-18
• /
• 2018

The primary purposes of this study are to understand a fundamental aspect of current uniformity around a reinforcing bar (rebar) in cement mortar, and to develop an accurate monitoring method in a wet-dry cycling process with the alternative current (AC) impedance method. Three cement mortar specimens with two embedded rebars were prepared in the laboratory. As a main variable, the distance between two rebars was designed to be 10, 20 and 30 mm with the same thickness of 20 mm. To simulate the corrosion of rebars in concrete structures in a marine environment, three cement mortar specimens were exposed to 15 wet-drying cycles (24-hour-immersion in seawater and 48-hour-drying in a room temperature) in the laboratory. It was observed that the potential level shifted to a noble value during corrosion potential monitoring, which is attributed to acceleration of dissolved oxygen diffusion at the drying process. AC impedance was measured in a frequency range from 100 kHz to 1 mHz on a wet-drying process. A theoretical model was proposed to explain the interface condition between the rebars and cement mortar by using the equivalent circuit consisting of a solution resistance, a charge transfer resistance and a CPE (constant phase element). It was observed that the diffusion impedance appeared in a low frequency range as corrosion of rebars progresses. At the drying stage of the wet-drying cycles, the currents line for monitoring tended to be non-uniform at the interface of rebar/mortar, being phase shift, ${\theta}$, close to $-45^{\circ}$.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.103-103
• /
• 2015

유류유출사고와 같이 하천 수표면의 흐름에 따라 이동 확산하는 부유성 오염물질의 혼합해석을 위해 많은 연구자들은 입자추적모형을 사용한 혼합모의를 수행해왔다. 입자추적모형에서 오염물질의 혼합은 평균 유속 분포에 의한 결정론적인 이동과 난류유동에 의한 무작위적인 혼합으로 나타내며, 난류혼합에 의한 수평확산은 난류확산계수로 조절한다. 따라서 표면흐름에 의한 난류확산계수의 산정을 위해 많은 연구자들은 부유성 입자를 이용한 실내실험을 수행하여 수평확산계수를 산정했고(Engelund, 1969; Cederwall, 1971), 최근에는 GPS의 발전으로 인해 해양영역에서 GPS를 장착한 표면부자를 활용한 확산실험을 통해 수평확산계수를 산정한 바 있다(Kjellson and $D{\ddot{o}}{\ddot{o}}s$, 2012; Alpers 등, 2013). 하천수질오염사고의 약 43.5%가 유류유출에 의한 것이며(환경부, 2013), 이에 따라 표면흐름에 의한 오염물질 혼합해석이 필요하나, 하천에서 수평확산계수 산정을 위한 현장실험연구는 부족한 상황이다. 따라서 본 연구에서는 낙동강 본류에서 GPS부자를 이용한 입자추적실험을 수행하여 표면흐름에 의한 확산계수를 산정했다. GPS부자를 이용한 입자추적실험은 낙동강의 강정고령보 하류와 구미보 하류의 각각 세 지점에서 수행되었다. GPS부자는 바람에 의한 교란을 최소화하기 위해 지름 10 cm의 구형으로 제작하였으며 시범테스트를 통해 입자의 주 궤적 변화가 크지 않은 지점에 GPS부자를 투입했다. GPS부자는 오염물질의 사고유출을 가정하여 한 지점에 투입했고 GPS부자 사이의 간섭을 최소화하기 위해 25 ~ 35개의 GPS부자를 이용했다. 표면흐름에 의해 이동하는 부자의 위치는 GPS에 시계열로 저장됐고 ADCP를 이용하여 실험당시의 수리량을 측정했다. 입자위치의 시계열자료로부터 GPS부자의 확산범위의 시간변화를 계산했고 단순 모멘트법을 이용하여 종, 횡 방향 확산계수를 계산했다. 그 결과, 종 방향 확산계수는 $0.003{\sim}0.041m^2/s$로 계산되었고 횡 방향 확산 계수는 $0.001{\sim}0.012m^2/s$로 계산되어, 흐름방향의 유속성분에 의한 확산이 지배적인 것으로 나타났다. 지류 합류부에서는 이송이 지배적인 혼합이 발생되었고(Pe>1) Pe의 증가에 따라 수평확산계수가 감소되었다. 25~35개 GPS부자 궤적의 앙상블 평균으로부터 계산한 Integral time scale은 모멘트법으로부터 계산한 종, 횡 방향 확산계수와 비례하는 것으로 나타나, Taylor(1921)의 이론과 일치했다. 또한 실험수로에서 수행된 기존연구결과와 비교한 결과, 하폭 대 수심비, 마찰항의 증가에 따라 수평확산계수가 증가하는 경향을 나타내었다.

• Tunnel and Underground Space
• /
• v.32 no.6
• /
• pp.491-501
• /
• 2022

Bentonite has been proposed as a buffer and backfill material for high-level radioactive waste repository. Under such repository environment conditions, bentonite is subjected to combined thermal, hydrological, mechanical, and chemical processes. This study evaluates the feasibility of applying X-ray CT technology on the characterization of bentonite under hydration conditions using a newly developed testing cell. The cylindrical cell is made of platic material, with a removable cap to place the sample, enabling to apply vertical pressure on the sample and to measure swelling pressure. The hydration test was carried out with a sample made of Gyeonju bentonite, with a dry density of 1.4 g/cm³, and a water content of 20%. The sample had a diameter of 27.5 mm and a height of 34 mm. During the test, water was injected at a constant pressure of 0.207 MPa, and lasted for 7 days. After one day of hydration, bentonite swelled and filled out the space inside the cell. Moreover, CT histograms showed how the hydration process induced an initial increase and later progressive decrease on the density of the sample. Detailed profiles of the mean CT value, CT standard deviation, and CT gradient provided more details on the hydration process of the sample and showed how the bottom and top regions exhibited a decrease on density while the middle region showed an increase, especially during the first two days of hydration. Later, the differences in CT values with respect to the initial state decreased, and were small at the end of testing. The formation and later reduction of cracks was also characterized through CT scanning.

• Journal of the Korean GEO-environmental Society
• /
• v.19 no.5
• /
• pp.23-31
• /
• 2018

The dredging project became more important with the recent construction of off shore structures and reclamation projects. Accordingly, more exact quantitative estimation of the dredged amount should be required. The sub-sea ground information can be obtained generally by the boring investigation and the dredged amount can be estimated based on the depth or the deeper bound of a ceratin layer via 3D visualization program. During the estimation process, the input DB should be constructed with 1D elevation information from boring investigation for the spatially approximated distribution of a deeper bound of each ground layer. The input DB can be varied with the application of the borings and the approximation targets. Therefore, the 3D visualized ground profile and dredged amounts are compared on the actively dredged sites, vicinity of Saemangeum area and outer port area in Gunsan with regard to the input DB construction methods. Conclusively, the input DB based on the spatially approximated depths show higher precision results and more reasonable 3D visualized ground profiles.

• Journal of Life Science
• /
• v.31 no.6
• /
• pp.559-567
• /
• 2021

This study compared the nutritional characteristics and antioxidant effects of sea mustards sourced from five different areas (Barammaegi, Gultongmeori, Chanmulgae, Johongtaek, and Goraedeung) in Taejongdae, Youngdo, Busan. The contents of total flavonoids and phenols and fatty acid composition were measured. To evaluate their antioxidant effects, 1,1-diphenyl-2-picrylhydrazyl (DPPH) and 2,2'-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) assays were used. Acetone/methylene chloride (A+M) extracts from all the sea mustards contained higher amounts of total flavonoids and phenols than methanol (MeOH) extracts. Among the sea mustards obtained from the different areas, the total flavonoid and total phenolic content of the A+M extract of the sea mustard from Gultongmeori was 1.44±0.04 mg/g and 1.72±0.06 mg/g, respectively. In terms of the fatty acid composition, the Gultongmeori sea mustard had higher percentages of total n-6, total n-3, eicosapentaenoic acid (EPA, 20:5n-3), and docosahexaenoic acid (DHA, 22:6n-3) than the sea mustards from the other areas. The A+M extract of the sea mustard from Gultongmeori was more effective in terms of scavenging free radicals as compared with that of the other sea mustards, as assessed by the DPPH and ABTS assays (p<0.05). In a 120-minute reactive oxygen species (ROS) production assay, all the extracts tested decreased cellular ROS production induced by H₂O₂ compared to that produced by exposure to an extract-free control (p<0.05). The extracts from Barammaegi and Gultongmeori had a greater inhibitory effect on cellular ROS production. These results indicated that the antioxidant effects of sea mustards might be associated with a higher amount of flavonoids and phenols. This study suggests that food-processed products from sea mustard can be developed as functional foods for promoting health in the local population.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.18 no.2
• /
• pp.1-9
• /
• 2022

A novel steel-pipe energy pile is introduced, in which the deformed rebars for main reinforcing are replaced with steel pipes in a large diameter cast-in-place energy pile. Here, the steel pipes act as not only reinforcements but also heat exchangers by circulating the working fluid through the hollow hole in the steel pipes. Under this concept, the steel-pipe energy pile can serve a role of supporting main structures and exchanging heat with surrounding mediums without installing additional heat exchange pipes. In this study, the steel-pipe energy pile was constructed in a test bed considering the material properties of steel pipes and the subsoil investigation. Then, the thermal performance test (TPT) in cooling condition was conducted in the constructed energy pile to investigate thermal performance. In addition, the thermal performance of the steel-pipe energy pile was compared with that of the conventional large diameter cast-in-place energy pile to evaluate its applicability. As a result, the steel-pipe energy pile showed 11% higher thermal performance than the conventional energy pile along with much simpler construction processes.

• Corrosion Science and Technology
• /
• v.20 no.6
• /
• pp.451-465
• /
• 2021

In this investigation, electrochemical characteristics and damage behavior of 316L stainless steel polymer electrolyte membrane fuel cell(PEMFC) were analyzed by potentiodynamic and potentiostatic tests in cathode operating condition of PEMFC. As the result of potentiodynamic polarization test, range of passive region was larger than range of active region. In the result of potentiostatic test, damage depth and width, pit volume, and surface roughness were increased 1.57, 1.27, 2.48, and 1.34 times, respectively, at 1.2 V compared to 0.6 V at 24 hours. Also, as a result of linear regression analysis of damage depth and width graph, trend lines of damage depth and width according to applied potentials were 16.6 and 14.3 times larger, respectively. This demonstrated that applied potential had a greater effect on pitting damage depth of 316L stainless steel. The damage tendency values were 0.329 at 6 hours and 0.633 at 24 hours with applied potentials, representing rapid growth in depth direction according to the test times and applied potentials. Scanning electron microscopy images revealed that surface of specimen exhibited clear pitting damage with test times and applied potentials, which was thought to be because a stable oxide film was formed by Cr and Mo.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.7
• /
• pp.23-29
• /
• 2011

The oxidation slag has been widely used in civil engineering project, whereas the reduced slag from electric furnace has yet to be applied. Consequently in order to find out the recycling method in civil engineering field, the mineral compositions of the reduced slag were analyzed and some tests on water quality were performed to estimate the potential release of toxic compounds. Slag-soil mixtures of 0, 10, 20 and 30%(dry weight) soil were prepared in lysimeter columns and the effluents were collected with the period of one, two and four week options in closed system, respectively. The result from qualitative and quantitative analysis using X-ray Diffraction(XRD) and X-ray Fluorescence(XRF) indicates that the main mineral of the reduced slag is $Ca_2(SiO_4)$, a kind of calcium silicate. Also, the leaching medium analyzed by Inductively Coupled Plasma Optical Emission Spectroscopy(ICP-OES) showed that main heavy metals such as Al, Fe and Mn are included in the reduced slag due to the effect of steel production process. It can be seen that the leachate does not violate the regulation guide line of waste material of heavy metal. Also the pH levels were increased from pH 6.9 for 0% soil to pH 10 for 30% soil. However the influence on leachate circulation period of one through four weeks was negligible.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.3
• /
• pp.79-85
• /
• 2005

An experimental study was carried out to investigate the recycling possibility of waste oyster shells, which induce environmental pollutions by piling up out at the open or the temporary reclamation. The purpose of this study is to develope eco-friendly binder using waste oyster shells, and to reinforce dredged soils fur soft soil improvement. In this paper, a series of laboratory tests including compressive strength tests were performed to evaluate strength characteristics of soils treated by developed binder with different water content of dredged soils, mixing rates of binder, curing days. Based on test results, eco-friendly binders manufactured from waste oyster shells were estimated as good resource materials for soft soil improvements.