• Proceedings of the Korea Water Resources Association Conference
• /
• 2019.05a
• /
• pp.42-42
• /
• 2019

유량조절을 위한 자동수문은 설정된 관리수위 이하에서는 수문이 개방되지 않으며, 유량이 증가하여 관리수위 이상이 되면 수문이 개방되어 방류를 시작하여 일정 수위를 유지하는 것을 의미한다. 자동수문의 운영 중 수문의 거동과 자동 개폐 시점을 예측하는 것은 정밀한 수문 설계를 위해 매우 중요하다. 수문 하단으로 흐름이 발생하면 수문 선단을 포함한 주변에서의 압력 차이로 인한 동수압 하중이 발생하고 진동을 유발, 수문 개방을 억제하는 하향력 등의 효과로 수문 운영에 큰 영향을 미친다. 본 연구에서는 부력식 수문의 모형실험을 통하여 정수압 상태의 부력 이론에 의한 수문 개방률과 측정에 의한 수문 개방률을 비교하였으며, 이론과 측정 수문 개방고의 차이를 하향력에 의한 효과임을 확인하였다. 부력식 수문의 하향력을 검토하기 위해 기존 이론식을 이용한 결과, 이론식은 부력식 수문에 적용하기 어려운 것으로 나타났다. 따라서, 기존 이론식을 이용하여 부력식 수문의 하향계수 산정을 위한 매개변수 관계식을 개방률을 이용하여 제시하였다. 제시된 매개변수 관계식의 결정계수는 0.721, 수정된 결졍계수는 0.690으로 나타났다. 부력식 수문의 형상비에 따른 하향력을 검토하기 위해서 수치모의를 수행하였다. 모형실험에서 측정된 자료와 수치모형 ANSYS-Fluent의 사용성을 검증하였고, 부력식 수문의 형상비를 0.24, 0.49, 0.69, 0.89, 1.09로 총 5가지로 설정하여 하향계수와 하향력을 분석하였다. 부력식 수문의 하향계수와 하향력 검토는 부력체, 스커트로 구분하여 분석을 수행하였다. 하향계수 분석결과, 하향계수는 개방률이 증가함에 따라 감소하였으며 하향계수가 부력체 부분에서는 0.465~1.542, 스커트 부분에서는 0.058~1.148의 범위로 나타났다. 하향력 분석결과, 하향력은 개방률 0.300 이하에서는 개방률이 증가함에 따라 하향력은 증가하였나 개방율 0.300 초과하면서부터 개방률이 증가함에 따라 하향력이 감소하는 것으로 나타났다. 또한 부력체 부분에서는 형상비가 증가함에 따라 하향력이 감소하였으나, 스커트 부분에서는 형상비가 증가함에 따라 하향력이 증가하였다. 이는 형상비가 증가함에 따라 스커트 부분의 면적이 증가하기 때문이다. 부력식 수문의 전체적인 하향력을 계산한 결과, 부력식 수문의 하향력은 0.002~0.015 kN의 범위를 가지며 형상비가 증가함에 따라 부력식 수문에 발생하는 하향력은 증가하는 것으로 나타났다.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.3
• /
• pp.65-74
• /
• 2003

The dragload on pile groups in consolidating ground was investigated based on a numerical analysis. The case of a single pile and subsequently the response of groups were analyzed by 2D and 3D finite element studies. Conventional continuum elements and special slip elements were used in the analyses for comparison. Based on a limited parametric study, it is shown that dragload for a single pile and group effect are normally overestimated by continuum analyses, compared with the predictions by the slip analyses. The group effect was examined from the slip analysis by considering various factors such as pile configurations, surface loading, interface friction coefficient, and axial loading on piles. An examplary analysis and one previous experimental observation of dragload and group effects were back-analysed. The case histories demonstrated that the slip analysis might predict a better estimate of dragload and group effect compared to the no-slip continuum analysis.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.10
• /
• pp.11-16
• /
• 2013

Success or failure of the bi-directional pile load test for drilled shaft depends on point selection for loading cells, that is balanced location both uplift force and downward force. Methods to evaluate the ultimate unit side resistance in rockmass layer in both domestic and foreign are based on the uniaxial compression strength of rock core, which can hardly be obtained in domestic rockmass layers which are weathered rockmass layer and soft rockmass layer with very low RQD. Therefore, this study suggested the relation charts between the revised SPT N values and developed unit side resistance of each different layers, which were obtained from bi-directional pile load tests in various domestic sites. To evaluate the appropriateness of the relation charts, the developed unit side resistances from the relation charts were used to select the loading cell position and compared with the measured unit side resistances from field pile load test. Results showed that the developed side resistance from relation charts and the measured side resistance of weathered soil layer and weathered rock layer were very close. Average developed side resistance($1,325kN/m^2$), which are average of upper soft rock layer of loading device($1,151kN/m^2$) and lower($1,500kN/m^2$), was similar with the estimated value ($1,250kN/m^2$).

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.2
• /
• pp.206-214
• /
• 1988

To improve the surface waviness in the peripheral milling, the feedrate is controlled so that the cutting force measured in the normal direction to the workpiece is constant. A discrete time first order model between the feedrate and the tool deflection is derived for the control. It has been shown by the analysis that the tool deflection is directly related to the feedrate and largely affects the surface waviness during cutting. The experimental results shown that the surface waviness is drastically improved by the proposed methods.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.907-911
• /
• 2000

In this study, a modified model for prediction of cutting force components in down end milling process is presented. Using this cutting force components of 4-tooth endmills with various helix angles have been predicted. Predicted values of cutting force components are well coincide with the measured ones. As helix angle increases overlapping effects of the active cutting edges increase and as a result the amplitudes of cutting force components decrease.

• Geotechnical Engineering
• /
• v.3 no.1
• /
• pp.39-52
• /
• 1987

Model pile tests are performed, first, to estimate donwndrag exerted on pile surfaces due to the settlement of surrounding soils, and, second, to evaluate the efficiency of the downdrag reduction methods such as the bitumen coating method and the method of the attachment of an enlarged base. Test results show that the downdrag forces may be expressed as 0.25(;effective overburden). Bitumen coating reduces the downdrag by more than 50 percent, and the enlarged base attachment method is also effective, whose effectiveness increases as the sixte of the base increases as expected. When the bitumen coating and enlarged base are both applied, the downdrag force is reduced as much as 90 percent. Finally, it is found that the quantity of the relative displacement between the pile and the surrounding soil downdrag is extremely small.

• Korea journal of population studies
• /
• v.16 no.1
• /
• pp.59-68
• /
• 1993

본 연구는 1980년대 우리나라 출산력의 급격한 변동을 설명하기 위하여 1988년 한국보건사회 연구원에서 실시한 전국규모의 출산력 및 가족보건조사자료를 기초로 출산순위진도 측정방법에 의하여 출산력을 분석한 것이다. 본 연구 결과에서는 년도별 출산력과 출산순위분포, 출산순위별 진도율 등을 측정하였고, 그 결과를 요약하면 다음과 같다. 1980년 초에는 출산력이 2.8에서 1986년 이후에 대체수준이하인 1.8로 계속적인 하향추세를 보였다. 출산순위별 진도율에서는 둘째에서 세째아이로 진도한 비율이 1980년초에서 1986년사이에 약 71%가 감소하였고, 세째순위에서 네째순위로 33%가 감소하였다. 세째이상으로 진도한 비율의 감소율이 90%를 상회하고 이중 둘째에서 세째사이의 변동율이 50%를 나타내었다. 출산순위분포에서는 둘째아이에 64%가 집중되어 있으며 출산진도율은 결혼에서 첫째아이로 진도되는 확률이 90%, 첫째에서 둘째로 85%, 둘째에서 세째로는 18%가 나타냈다. 이러한 현상은 최근 한국부인의 82%가 둘째아이에서 단산하는 경향을 보이고 한자녀만 갖는 확률은 15%로 풀이되고 있다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.10A
• /
• pp.958-964
• /
• 2005

In this thesis, the matching network at the local oscillator port of the sub-harmonic mixer is optimized for reducing the conversion loss. A downconverter for point to point system applications is designed and fabricated using the such sub-harmonic mixer. The sub-harmonic mixer achieved the conversion loss of 11.8 dB at the 12 dBm input power of the local oscillator and the isolation of less than -40 dB. The downconverter achieved the IF output power flatness of 2 dB and the total noise figure of 5.9 dB.

• The Korean Journal of Applied Statistics
• /
• v.34 no.2
• /
• pp.177-190
• /
• 2021

Random forests is a popular method that improves the instability and accuracy of decision trees by ensembles. In contrast to increasing the accuracy, the ease of interpretation is sacrificed; hence, to compensate for this, variable importance is provided. The variable importance indicates which variable plays a role more importantly in constructing the random forests. However, when a predictor is correlated with other predictors, the variable importance of the existing importance algorithm may be distorted. The downward bias of correlated predictors may reduce the importance of truly important predictors. We propose a new algorithm remedying the downward bias of correlated predictors. The performance of the proposed algorithm is demonstrated by the simulated data and illustrated by the real data.

• Korean Journal of Food Science and Technology
• /
• v.38 no.5
• /
• pp.659-667
• /
• 2006

In order to standardize the manufacturing processes of Hahyangju, a traditional Korean liquor, 29 yeast strains were isolated from traditional Nuruk. Strain N8 exhibited a particularly strong resistance to sugar. Strains HA2, HA3 and HA4 grew successfully in medium containing 10% ethanol. In comparison with the growth exhibited by these strains when grown in a yeast malt extract medium, the ethanol production rates for the three strains were 10.8%, 10.45%, and 10%, respectively in a yeast malt extract medium containing 25% glucose. Based on these results, HA3 was the strain selected for use in the manufacturing processes of Hahyangju and it was identified as a Saccharomyces cerevisiae strain with 97% ITS sequence similarity. The use of Saccharomyces cerevisiae HA3 causcd a decrease in the lactic acid content, acidity and growth of lactic acid bacteria in the fermentation mash. Following thc addition of Saccharomyces cerevisiae HA3 to the manufacturing process of Hahyangju, the second fermentation mash showed a 22% increase in the alcohol production rate associated with traditional fermentation; however, the amino acidity, pH and reducing sugar content showed little change. Sensory evaluation of Hahyangju fermented with S. cerevisiae HA3 also showed better scores than Hahyangju mashed by the traditional method.