• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.83-87
• /
• 2005

In this paper, the combustion characteristics of a hybrid propulsion system were studied with various L/D(length vs diameter) ratio of the single port type solid fuel. Experiments of L/D ratio change were performed for 2 cases with the fixed grain port diameter and fuel length respectively. For the First case, results show that there are no large variation for regression rates as the L/D ratio changes. And as the L/D ratio increases, the O/F ratio and thrust tends to increase. For the Second case, there are no large change for O/F ratio and thrust as L/D ratio changes. On the other hand, as the L/D ratio decreases, only the regression rate tends to increase.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.4
• /
• pp.31-38
• /
• 2005

In this paper, the combustion characteristics of a hybrid propulsion system were studied with various L/D(length vs diameter) ratio of the single po.1 type solid fuel. Experiments were performed for 2 cases with the fixed grain port diameter and fuel length respectively. For the first case, results show that there are no large variations for regression rates as the L/D ratio changes. And as the L/D ratio increases, the O/F ratio decreases and thrust, characteristic velocity tends to increase. For the second case, there is no large change for O/F ratio, thrust and characteristic velocity as L/D ratio changes. On the other hand, as the L/D ratio decreases, only the regression rate tends to increase. Experimentally, exponent n in $\dot{r}=a{G_0}^n$ was found about 0.5 and then the O/F ratio was shown nearly constant. In the experiment, PE and gas oxygen were used as a fuel and an oxidizer.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.210-213
• /
• 2010

Recent experimental data shows that the noticeable feature of irregular roughened spots on the fuel surface occurs during the combustion test. The generation of these unexpected patterns is likely to be resulted from the disturbed boundary layer due caused by wall blowing which is intended to simulate the process of fuel vaporization. LES without chemical reaction was conducted to investigate the flow characteristics at the near-fuel surface and the behavior of turbulent structures which is evolved by the wall blowing at the Reynolds number of 23,000. Cylindrical geometry was considered to get the most reality of the calculation results because real hybrid rocket motor is circular grain configuration. It was shown that the wall blowing pushed turbulent structures upwards making them tilted and this skewed displacement, in effect, left the foot prints of the structures on the surface. This change of kinematics may explain the formation of irregular isolated spots on the fuel surface observed in the experiment.

• 한국항공운항학회:학술대회논문집
• /
• 2015.11a
• /
• pp.13-19
• /
• 2015

본 연구의 목적은 자체 설계 제작한 하이브리드 발사체를 이용하여 대기 중의 미세먼지를 측정하는데 있다. 대기 중의 미세먼지를 측정하기 위한 방법으로는 중량농도법을 이용하였으며, 미세먼지 측정을 위한 포집장치를 자체 제작하였다. 엔진은 5port의 HDPE(High Density Polyethylene)를 연료 그레인으로 사용하였고 $LN_2O$(Liquefied Nitrous Oxide)를 산화제로 사용하였다. 압력, 가속도, GPS 등을 수집하며, 하이브리드 발사체의 동체는 FRP(Fiberglass Reinforced Plastics)로 제작한다. 전체 비행시간은 총 95초로 예상되며. 연소시간은 3초, 고도는 800 m 이다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.45-49
• /
• 2011

The blow-down oxidizer feed system with self-pressurizing $N_2O$ has more advantages than the regulated system. However, it is difficult to predict the exhaust flow rate because there exist two phases in the $N_2O$ tank - liquid phase and gas phase, and the properties of $N_2O$ in storage tank are varied continuously during blow-down. In this paper, a method that can analyse simply the blow-down oxidizer feed system is studied. The properties of saturated $N_2O$ are found from the NIST data base, and mass flow through the orifice is modeled as NHNE. Cold flow test with hybrid rocket combustor is performed for the comparison where the results should found from the good agreement.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2001.11a
• /
• pp.55-60
• /
• 2001

Recently, there have been many research efforts to improve the fuel regression rate in the hybrid rocket engines. In the present study, the ongoing research and development of the next general ion hybrid rocket engine are systematically reviewed. The detailed discussions have been made for the innovative combust ion technologies including the vortex hybrid rocket engines , cryogenic sol id propellant hybrid rocket engine, and the gas generator hybrid rocket engines.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.12
• /
• pp.1108-1114
• /
• 2007

The effect of oxidizer injection angle on the combustion characteristics of end-burning hybrid combustor is numerically investigated. Besides the previously studied parameter(injector arrangement, port diameter and O/F ratio), three different injection angle are considered: parallel angle to fuel surface(Case 1), +30 degree inclined angle toward the fuel(Case 2) and 30 degree inclined angle toward the nozzle(Case 3). It is found that Case 2 has the best mixing pattern in the upstream area but has the worst combustion efficiency since non negligible amount of unburned fuel is expelled from the nozzle. In contrast, though Case 1 and Case 3 showed relatively low mixing effect than the Case 2, they had high combustion efficiency. The comparison of numerical results between Case 1 and Case 3 demonstrate that no major difference is encountered, however, Case 1 is expected to have the best combustion efficiency due to the low residence time of the Case 3 injector which heads toward the nozzle.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.233-237
• /
• 2007

Recent experimental data shows that an irregular fuel surface pops up during the combustion test. This may contribute to the agitated boundary layer due to blowing effect of fuel vaporization. Blowing effect can be of significance in determining the combustion characteristics of solid fuel within the oxidizer flow. LES was implemented to investigate the flow behavior on the fuel surface and turbulence evolution due to blowing effect. Simple channel geometry was used for the investigation instead of circular grain configuration without chemical reactions. This may elucidate the main mechanism responsible for the formation of irregular isolated spots during the combustion in terms of turbulence generation. The interaction of turbulent flow with blowing mass flus causes to breakup turbulent coherent structures and to form the small scale isolated eddies near the fuel surface. This mechanism attributes to the formation of irregular isolated sopt on the fuel surface.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.139-141
• /
• 2017

By modulating the flow rate of $N_2O$ into a HR motor assembly, a control valve of a hybrid rocket engine plays a role to increase or decrease the thrust. In this study, the control valve has been designed to meet the requirements which are response speed(${\leq}$ about 1 second) and torque(${\geq}$ about $36N{\cdot}m$). Then, when analog signal 0~10V is applied, the situation where the valve is opened and closed has to be realized. To do this, the data values have to be entered into the actuator. Finally, the performance evaluation of the control valve has been performed to validate this product.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.30 no.4
• /
• pp.184-190
• /
• 2022

In an attempt to apply hybrid rocket to the RATO (Rocket-Assisted Take Off) system, combustion characteristics of the non-circular grain were figured out in this study. Having larger combustion area, it was reconfirmed that the non-circular grain has advantages over regression rate, characteristic velocity and chamber pressure in which all gave higher values. Experiments were performed to understand the effect of the non-circular grain geometry over time where local regression rates depending on grain location were analyzed. It was found that the regression rate of five distinct locations were different. Partial conclusion driven was that these differences are due to the heat transfer caused by dissimilar distances from the flame layer. Besides, as combustion duration increased, the fuel port became circular, and the regression rate converged to a single value over the whole grain.