• Journal of the Korean Magnetics Society
• /
• v.7 no.1
• /
• pp.13-18
• /
• 1997

The effects of the various raw material composition and sintered temperature on the physical properties of Ni-Zn ferrite have been investigated. They turned out to be spinel structure by X-ray diffraction and the size of grain from microscope was from 6 ${\mu}{\textrm}{m}$ to 16 ${\mu}{\textrm}{m}$. As the sintering temperature was increased from 1030 $^{\circ}C$ to 1070 $^{\circ}C$, the initial permeability and magnetic induction has increased and the both of Q factor and coercive force has decreased. The coercive force and curie temperature were almost the same at each specimen. Their values were about 0.20 Oe and 220 $^{\circ}C$. The frequency of specimen will used in the range from 400 kHz to 20 MHz. The basic composition of $Ni_{0.14}Zn_{0.64}Cu_{0.22}Fe_2O_4$ (specimen B) sintered at 1050 $^{\circ}C$ shows the best results at magnetic induction($B_r & B_m$).

• Journal of the Korean Ceramic Society
• /
• v.38 no.8
• /
• pp.765-770
• /
• 2001

광촉매용 ZnO 나노크기의 분말은 시작원료와 연료의 종류에 따라 용액연소법에 의해 제조되었다. 결정상은 XRD로부터 확인할 수 있었으며 분말의 하소온도는 TG 분석으로부터 결정되었다. 분말의 비표면적은 BET 법에 의해 측정되었으며 평균입자크기와 형태를 SEM과 TEM으로부터 조사하였다. 또한 분말의 순도를 조사하기 위해 적외선 흡수스펙트럼을 측정하였으며 광촉매 효율로서 은이 첨가된 사진현상액을 이용하여 은의 수거율을 측정하였다. 용액연소법으로 제조한 경우 시작원료와 연료에 관계없이 단상의 ZnO 분말을 쉽게 얻을 수 있었다. 그러나 합성된 ZnO 분말의 입자크기와 형태는 연료의 종류에 따라 서로 다르게 보였다. 특히, 연료로 glycine을 사용한 경우, ZnO 분말의 입자 형태는 균일한 나노 크기의 구형이었으나 carbohydrazide을 사용한 경우에는 판상과 같은 형태를 보였다. 이러한 결과를 기초로 하여 시작원료와 연료로 Zn(OH)$_2$와 glycine을 사용하여 합성된 ZnO 분말이 우수한 분말 특성을 보였으며 75nm의 입자크기와 94$m^2$/g의 비표면적을 보였다. 또한 사진현상액에 존재하는 은이 3분 이내에 완전히 제거되는 우수한 광촉매 성질을 보였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.3
• /
• pp.152-156
• /
• 2017

In this paper, $Pb(Mn_{1/3}Nb_{2/3})_{0.07}(Ni_{1/3}Nb_{2/3})_{0.10}(Zr_{0.5}Ti_{0.5})_{0.83}O_3$ ceramics were fabricated by the conventional solid state method to obtain excellent dielectric properties for ultrasonic generators. The effects of 2nd calcination temperature on their microstructure and piezoelectric properties were systematically investigated. The tetragonality increased in the ceramics when 2nd calcination temperature increased to the optimized temperature at $750^{\circ}C$. At that temperature, excellent physical properties ($d_{33}=352\;pC/N$, ${\varepsilon}_r=1,687$, $k_p=0.570$, $Q_m=1,640$) were obtained for ultrasonic generator application.

• Journal of Powder Materials
• /
• v.19 no.6
• /
• pp.412-415
• /
• 2012

The quartz glasses were prepared by sintering of fumed silica powders and the effect of OH concentration on their surface on sintering was studied. Through the firing process, the fumed silica was crystallized from 1180 to $1260^{\circ}C$ region. The amount of hydroxyl group decreased with increase in calcination temperature and consequently the crystallization was prevented. A transparent quartz glass was obtained from fumed silica, previously calcined at $1000^{\circ}C$, by the sintering at $1250^{\circ}C$ for 1 h.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.9
• /
• pp.821-826
• /
• 2005

In this paper, in order to develop lead-free piezoelectric ceramics, $(Li_{0.04}Na_{0.44}K_{0.52)(Nb_{0.86}Ta_{0.10}Sb_{0.04})O_3$ ceramics were fabricated with the variation of calcination temperature and sintering temperature. The ceramics couldn't be sintered at temperature less than $1110^{\circ}C$ and showed the highest density at calcination temperature of $800^{\circ}C$. Crystal structure of the ceramics showed pseudo-tetragonal phase. At the calcination temperature of $800^{\circ}C$ and sintering temperature of $1110^{\circ}C$, the optimal values of $density=4.64g/cm^3,\;kp=0.45,\;{\varepsilon}r=1336,\;d_{33}=254pC/N\;and\;Tc=335^{\circ}C$ were obtained.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.214-216
• /
• 2006

In this study, in order to develop the composition ceramics for low loss and low temperature sintering multilayer piezoelectric actuator, PMN-PZN-PZT ceramics were fabricated using two stage calcination method and $Li_2CO_3$, $Bi_2O_3$ and CuO as sintering aids and their piezoelectric characteristics were investigated according to the 2nd calcination and sintering temperature. At the calcination temperature of $750^{\circ}C$ and sintering temperature of $930^{\circ}C$, density, electromechanical coupling factor ($k_p$), mechanical quality factor ($Q_m$), Dielectric constant (${\varepsilon}_r$) and piezoelectric constant ($d_{33}$) of specimen showed the optimum value of $7.94g/cm^2$ 0.581, 1554, 1555 and 356pC/N, respectively for multilayer piezoelectric actuator application.

• Journal of the Korean Ceramic Society
• /
• v.31 no.12
• /
• pp.1561-1569
• /
• 1994

Effect of calcining temperature on the sintering behaviors and microwave dielectric properties of BMT[Ba(Mg1/3Ta2/3)O3] ceramics was studied. The calcining temperatures were varied from 80$0^{\circ}C$ to 130$0^{\circ}C$, respectively. It was found that, as calcining temperature lowered below 125$0^{\circ}C$, second phase such as Ba5Ta4O15 phases started to appear in calcined powder with unreacted powders. After sintering, exaggerately grown Ba5TaO3 phase could be found amang the uniform BMT grains in sintered body. Basis on the infiltration experiment, Ba0.05TaO3 phase should be formed by reaction of BMT grain and BaO-MgO eutectic liquid. But increase of calcining temperature above 125$0^{\circ}C$, there was not any second phase or unreated component in calcined powder and sintered body. As result, low calcining temperature led to precipitation of second phase in specimen and resulted decrease of Q value of BMT ceramics.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.9
• /
• pp.651-655
• /
• 2013

$(Ba_{0.85}Ca_{0.15})(Ti_{0.9}Zr_{0.1})O_3$ + 0.04 wt% $CeO_2$ lead-free ceramics were synthesized by conventional sintering process and the effect of calcination temperature on microstructure, dielectric and piezoelectric properties were investigated. Improved piezoelectric properties have been observed at $1,125^{\circ}C$ calcination temperature which show the optimal electrical properties, $k_p$~0.457, $d_{33}$~367 pC/N, $Q_m$~158 and $T_c$~$85^{\circ}C$. These results show that the piezoelectric properties can be improved by appropriate calcination temperature.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.3
• /
• pp.217-221
• /
• 2008

In this study, We have been investigated the effect of calcination temperature and high-energy ball-milling of powder influences the $BaTiO_3$-based PTCR(Positive Temperature coefficient Resistance) characteristics and microstructure. The mixed powder was obtained from $BaCO_3$, $TiO_2$, $CeO_2$ ball-milled in attrition mill. The mixed powder was calcine from 1000 $^{\circ}C$ to 1200 $^{\circ}C$ in air and then it was sintered in reduction- re-oxidation atmosphere. As a result, The room-temperature electrical resistivity decreased and increased with increasing calcination temperature. specially, Attrition milled powder could have low room-temperature resistivity and high PTC jump order at 1100 $^{\circ}C$. attrition milling had lower room-temperature resistivity than ball milling. Particle size decreased by Attrition milling of powder influences in calcination temperature and room-temperature resistivity.

• Membrane Journal
• /
• v.21 no.3
• /
• pp.229-235
• /
• 2011

In this study, mesoporous titania/alumina membranes were prepared by sol-gel method. Pore structure and phase composition of titania/alumina membranes could be changed by calcination temperature. The addition of alumina into titania membranes retarded anatase-to-rutile phase transformation, resulting in stabilization of pore structures. The 5 time dip-coated membrane calcined at $450^{\circ}C$ is about $10.3{\mu}m$ in thickness with an average pore size of 5 nm. Hydrogen and nitrogen permeances through the membrane were $17.1{\times}10^{-7}mol/m^2{\cdot}s{\cdot}Pa$ and $4.7{\times}10^{-7}mol/m^2{\cdot}s{\cdot}Pa$, respectively. These data were explained by the Knudsen diffusion mechanism.