• The Journal of the Acoustical Society of Korea
• /
• v.22 no.5
• /
• pp.337-344
• /
• 2003

In DC/DC converter and VVVF inverter, which are the must dominant noise sources of Maglev train, noise is radiated from core and coil excited by MS(Magnetostriction). The main noise source of DC/DC converter is transformer whose spectrum shows strong peaks associated with harmonics of exciting frequency, On the other hand, LIM/VVVF noise is dominated by the harmonics of switching frequency, whereas harmonics of exciting frequency are not significant. As switching frequency is increased in VVVF inverter, it is shown that the harmonics are shifted to higher frequency range. If switching frequency is increased from 700㎐ to 2 ㎑, It is measured that noise can be reduced by 5 to 6 ㏈. Since complete mathematical description of MS phenomena is far beyond the present technology, vibration spectrum is investigated qualitatively in this paper, where effect of increasing switching frequency is confirmed.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.5
• /
• pp.65-71
• /
• 2011

This study analyzes about front axle through the analyses of stress, fatigue and vibration. Maximum equivalent stress is shown with the frequency of 60Hz in case of the harmonic vibration analysis applied with force. Among the cases of nonuniform fatigue loads, 'SAE bracket history' with the severest change of load becomes most unstable but 'Sample history' becomes most stable. In case of 'Sample history' with the average stress of 0 to $-2{\times}10^5MPa$ and the amplitude stress of 0 to $-2{\times}10^5MPa$, the possibility of maximum damage becomes 3%. This stress state can be shown with 6 times more than the damage possibility of 'SAE Bracket history' or 'SAE transmission'. The structural result of this study can be effectively utilized with the design of front axle by investigating prevention and durability against its damage.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.5
• /
• pp.21-28
• /
• 2012

This study analyzes about automotive engine tension bearing through the structural analyses of fatigue and vibration. Maximum equivalent stress is shown at the lower of tensioner. Among the cases of nonuniform fatigue loads, 'SAE bracket history' with the severest change of load becomes most unstable but 'Sample history' becomes most stable. In case of 'Sample history' with the average stress of 0 to $-10^{6}MPa$, the possibility of maximum damage becomes 3%. This stress state can be shown with 6 times more than the damage possibility of 'SAE Bracket history' or 'SAE transmission'. The structural result of this study can be effectively utilized with the design of tension bearing by investigating prevention and durability against its damage.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.3
• /
• pp.239-244
• /
• 2011

This study analyzes the behaviors on stress, fatigue and vibration about bulldozer in operation. Maximum equivalent stress is shown with the frequency of 100 Hz in case of the harmonic vibration analysis applied with force. Among the cases of nonuniform fatigue loads, 'SAE bracket history' with the severest change of load becomes most unstable but 'Sample history' becomes most stable. In case of 'Sample history' with the average stress of 0 to -105MPa and the amplitude stress of 0 to $1.617{\times}105MPa$, the possibility of maximum damage becomes 3.23%. This stress state can be shown with 5 times more than the damage possibility of 'SAE bracket history' or 'SAE transmission'. The structural result of this study can be effectively utilized with the design of bulldozer by investigating prevention and durability against its damage.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1000-1002
• /
• 2017

Here, the unsteady Navier-Stokes solver has been developed using implicit dual time stepping method. The implicit dual time stepping method introduced the pseudo time step for solving the new residual including the steady state residual and real time derivative. For the validation of code, Stokes 2nd problem, the laminar flow on the oscillating flat plate was selected and compare the calculating results with analytic solutions. The calculating velocity profile and skin friction has a good agreement with analytic solutions.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.6
• /
• pp.124-129
• /
• 2018

A non-linear vibration isolation system which is composed of a non-linear spring and a linear damper was proposed in past research. When the support of the isolation system is excited harmonically, the response component of the isolation system mass at the excitation frequency has been calculated approximately using the harmonic balance method. The response was approximated by a single mode, and the result was compared with a numerical result which is assumed as an accurate one. Next, the response was approximated by two modes, and the result was compared with the former one.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.7 no.2
• /
• pp.105-113
• /
• 2003

Because structural systems are becoming lighter and more flexible and have lower natural frequencies and dampings than before, coordinated rhythmic activities such as dancing, audience participation in arenas or concert halls, and aerobics result in undesirable levels of vibration. For rhythmic activities, it is resonant or near resonant behavior that result in significant dynamic amplification and hence human discomfort. The most rational design strategy is to provide enough of a gap between the natural frequency of a floor system and the dominant frequencies excited by planned human activities to assure reasonably that resonance will not occur. For the case study the vibration measurements were performed at the floor of a long-span multi-purpose hall during the rock concert of popular singer.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1991.04a
• /
• pp.7-9
• /
• 1991

차량 주행시 내부공간의 소음레벨의 변화를 "Booming"소음이라고 통칭하며, 이 소음의 주 원인은 엔진 회전수의 2차 하모닉(harmonic) 주파수 성분으로 구조적인 경로를 통하여 인체에 전달되게 된다. Booming 소음은 변화가 클 때 탑승자에게 큰 고통을 주며 차량 가치평가에 커다란 마이너스 요인이 된 다. 본 연구에서는 이러한 Booming 현상을 파악하고 대처하는 방법의 하나 로서 벡터해석법을 사용하고자 한다. 사용하고자 한다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.4
• /
• pp.22-30
• /
• 2011

This study analyzes harmonic vibration with natural frequency according to the configuration of damper clutch. In the case of double spring, equivalent stress at same direction of the revolution at inner and outer coil spring is over 30% as compared with at its opposite direction. Natural frequency or harmonic response with maximum deformation in case of the less coil pitch is below 3Hz as compared with in case of the more coil pitch. As the coil pitch of damper spring as the case 2 or 4 becomes smaller, its mass and deformation can be large. In these cases, spring constant and natural frequency become smaller. In the case 5 or 6 of double spring at natural vibration or harmonic response, the frequency becomes over 300Hz. As the result of this study is applied by the design of damper spring, the damage at its connected part is prevented and the durability can be predicted.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.5
• /
• pp.148-155
• /
• 2011

This study analyzes stress, fatigue and vibration at clutch on the rotation of wheel. Eigenfrequencies from 1'st to 6'th order about clutch assembly are shown with the vibration at more than 800Hz. Maximum equivalent stress is shown with the frequency of 800Hz in case of the harmonic vibration applied with force. Among the cases of nonuniform fatigue loads, 'SAE bracket history' with the severest change of load becomes most unstable but 'Sample history' becomes most stable. In case of 'Sample History' with the average stress of 0MPa to $-10^5$ MPa and the amplitude stress of 0MPa to $10^5$ MPa, the possibility of maximum damage becomes 3.23%. This stress state can be shown with 6 times more than the damage possibility of 'SAE bracket history' or 'SAE transmission'. The structural result of this study can be effectively utilized with the safe design of clutch.