• The Journal of Korean Academy of Prosthodontics
• /
• v.52 no.4
• /
• pp.279-286
• /
• 2014

Purpose: The aim of this study was to investigate the effect of implant thread profile on the marginal bone stresses which develop during implant insertion. Materials and methods: Four experimental implants were created by placing four different thread systems on the body ($4.1mm{\times}10mm$) of the ITI standard implant. The thread types studied in this study included the buttress, v-shape, reverse buttress, and square shape threads. In order to examine the insertion stress generation, 3D dynamic finite element analysis was performed which simulated the insertion process of implants into a 1.2 mm thick cortical bone plate (containing 3.5 mm pilot hole) using a PC-based DEFORM 3D (ver 6.1, SFTC, Columbus, OH, USA) program. Results: Insertion stresses higher than human cortical bone developed around the implants. The level of insertion stresses was much different depending on the thread. Stress level was lowest near the v-shape thread, and highest near the square shaped thread. Difference in the interfacial bone stress level was more noticeable near the valley than the tip of the threads. Conclusion: Among the four threads, the v-shape thread was turned out to minimize the insertion stress level and thereby create better conditions for implant osseointegration.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.2
• /
• pp.528-534
• /
• 2020

The early development and use of plate heat exchangers (PHE) were in response to stringent statutory requirements from dairy products in the late 19th century, but PHEs were not exploited commercially until the 1920s. Since then, although the basic concept of PHEs has changed little, its design and construction have progressed significantly to accommodate higher temperatures and pressures, as well as large heat exchanging capacities. The development of current chevron-type corrugated heat plates has been ongoing since the oil shock in the 1970s to improve energy efficiency. The development trend of PHEs is consistent with the development of larger heat plates with better thermal efficiency, lower pressure drop, and good flow distribution. In this study, the thermal performance of small heat plates (PHE-S) and large heat plates (PHE-L) with the same plate depth and corrugation pitch were analyzed experimentally for each channel (H, M, and L type) to suggest development directions of heat plates. The test results showed that for the convectional heat transfer coefficient, the PHE-S was on average, 16.5% higher in the H type, 25% higher in the M type, and 40% higher in the L type than PHE-L. In the case of the pressure drop, the PHE-S was 19% higher in the H type, 46% higher in the M type, and 61% higher in the L type than PHE-L. These results were attributed to the differences in fluid distribution areas between the PHE-S and PHE-L, among other potential causes.

• The Journal of the Acoustical Society of Korea
• /
• v.19 no.5
• /
• pp.60-64
• /
• 2000

This paper studies the relation between the Fundamental Frequency (F0) and the formants of simple vowels in the Korean language sung by sopranos. It is hewn that, in soprano singing, the F0 of a vowel affects its formants. For this reason the formants of simple vowels sung by sopranos must be considered in all over the soprano singing range. We recorded the five simple vowel sounds /a/, /e/, /i/, /o/, and /u/ sung by five professional sopranos from A3 (220.0Hz) to A5 (880.0Hz) in the major scale and compared the formants of the sung vowels with those of spoken vowels. We observed that F1 and F2 of sung vowels were stable in low F0 (lower than B4) but in high F0 (higher than B4), F1 and F2 lost their stabilities. In the case of /a/, /o/, and /u/, the slope of the F1-F2 graph was about 2.6, and those of the F0-F2 and F0-Fl graphs were 2.2-2.5 and 0.7-1.0, respectively. And as the F0 increases, the F1 and F2 of sung vowels /a/, /e/, /i/, /o/, and /u/ were almost the same. At A5, the Fl and F2 of five sung vowels had the same values. This results suggest that the relation between the F0 and the formants be used to synthesize soprano's singing vowels.

• Korean Journal of Optics and Photonics
• /
• v.22 no.1
• /
• pp.23-29
• /
• 2011

Bistable chiral splay nematic liquid crystal display (BCSN LCD) is a memory type liquid crystal display using splay and $-\pi$ twist states as two stable states. When the cell thickness to pitch (d/p) ratio is 0.25, splay and $-\pi$ twist states have permanent memory time. However, when the transition from $-\pi$ twist state to splay state is caused by a fringe field, pixel regions show that the splay state is not perfect, but rather includes a contribution from the $-\pi$ twist state. In this paper, we propose a reflective BCSN LCD using $-\pi$ twist state in which the two stable states do not coexist. The fabricated reflective BCSN LC cell shows a high contrast ratio of over 30:1 and response times of 950 ms and 450 ms in vertical and fringe field switching, respectively. The proposed cell also shows wide viewing angle characteristics of $180^{\circ}$ in left- and right directions.

• Solar Energy
• /
• v.13 no.1
• /
• pp.11-21
• /
• 1993

The purpose of this study was to investigate the enhancement of heat transfer without additional external power in the case of rectangular impingement air jet vertically on the flat heating surface. The technique used in the present study was placement of square rod bundles as a turbulence promoter in front of the heat transfer surface. The results obtained through this study were summerized as follws. High heat transfer enhancement was achieved by inserting rods in front of the heating flat plate. According to visulaization, it was examined because of flow acceleration and separation and disturbance of boundary layer. The smaller clerance between rod and heating plate was, the larger heat transfer effect became at each H/B. Arverage Nusselt number reached maximum at H/B=10 and the local augmentation rate of heat transfer became maximum at H/B=2. The maximum average heat transfer enhancement rate increase about 43% for the case of X/B=2 and C=1mm, compared to a flat plate without rods. The correlating equation of average Nusselt number and Reynolds number was obatined. As follws : ${\overline{Nu}}_0=1.249Re^{0.465}(C/A)^{-0.033}(H/B)^{0.013}$.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.4
• /
• pp.9-17
• /
• 2013

This paper describes an experimental program to investigate the shear behavior of insulated concrete sandwich panels (CSPs) with different types of GFRP shear connector. The study included testing of 13 insulated CSP specimens with two types of surface conditions for extruded polystyrene (XPS) insulation and various shapes of shear connectors. All specimens were loaded in direct shear by means of push-out and were consist of three concrete panels, two insulation layer and four rows of GFRP shear connectors. Load-relative slip between concrete panel and insulation response of CSP specimens has been established through push-out shear test. Test results indicate that the surface condition of insulation has a significant effect on the bond strength between concrete panel and insulation. The specimen used XPS foam with 10mm deep slot shows higher bond strength than those used XPS foam with meshed surface. Corrugated GFRP shear connectors show equivalent strength to grid GFRP shear connectors. Cross-sectional area and embedded length of shear connector have a notable effect on overall response and inplane shear strength of the CSP specimens.

• The Journal of the Acoustical Society of Korea
• /
• v.28 no.3
• /
• pp.229-238
• /
• 2009

This paper describes a sound engine of Korean traditional instruments, which are the Gayageum and Taepyeongso, by using a TMS320F2812. The Gayageum and Taepyeongso models based on commuted waveguide synthesis (CWS) are required to synthesize each sound. There is an instrument selection button to choose one of instruments in the proposed sound engine, and thus a corresponding sound is produced by the relative model at every certain time. Every synthesized sound sample is transmitted to a DAC (TLV5638) using SPI communication, and it is played through a speaker via an audio interface. The length of the delay line determines a fundamental frequency of a desired sound. In order to determine the length of the delay line, it is needed that the time for synthesizing a sound sample should be checked by using a GPIO. It takes $28.6{\mu}s$ for the Gayageum and $21{\mu}s$ for the Taepyeongso, respectively. It happens that each sound sample is synthesized and transferred to the DAC in an interrupt service routine (ISR) of the proposed sound engine. A timer of the TMS320F2812 has four events for generating interrupts. In this paper, the interrupt is happened by using the period matching event of it, and the ISR is called whenever the interrupt happens, $60{\mu}s$. Compared to original sounds with their spectra, the results are good enough to represent timbres of instruments except 'Mu, Hwang, Tae, Joong' of the Taepyeongso. Moreover, only one sound is produced when playing the Taepyeongso and it takes $21{\mu}s$ for the real-time playing. In the case of the Gayageum, players usually use their two fingers (thumb and middle finger or thumb and index finger), so it takes $57.2{\mu}s$ for the real-time playing.

• Journal of Wind Energy
• /
• v.13 no.4
• /
• pp.26-41
• /
• 2022

Three similarities (i.e., geometrical similarity, kinematic similarity and dynamic similarity) between a prototype and model must be satisfied to perform an experiment for a floating offshore wind turbine (FOWT). For dynamic similarity, most of the model tests in ocean engineering basins are performed based on the Froude number, so the scale effect for the wind turbine of an FOWT occurs by different Reynolds numbers between the prototype and model. In this study, various model test techniques for overcoming the scale effect of the wind turbine part of the FOWT are investigated. Firstly, model test techniques using simple approaches are reviewed, and the advantages and disadvantages of the simple approaches are summarized. Secondly, the model test techniques in recent projects that apply improved approaches are introduced including advantages and disadvantages. Finally, new approaches applying digitalization are reviewed, and the characteristics of the new approaches are introduced.

• Progress in Medical Physics
• /
• v.14 no.2
• /
• pp.131-140
• /
• 2003

As the importance of accuracy in measurings of 3-D anatomical structures continues to be stressed, an objective and quantitative of assessing image quality and accuracy of 3-D volume-rendered images is required. The purpose of this study was to evaluate the quantitative accuracy of 3-D rendered images obtained with MDCT, scanned at various scanning parameters (scan modes, slice thicknesses and reconstruction slice thickness). Twelve clinically significant points that play an important role for the craniofacial bone in plastic surgery and dentistry were marked on the surface of a dry human skull. The direct distances between the reference points were defined as gold standards to assess the measuring errors of 3-D images. Then, we scanned the specimen with acquisition parameters of 300 mA, In kVp, and 1.0 sec scan time in axial and helical scan modes (pitch 3:1 and 6:1) at 1,25 mm, 2.50 mm, 3.75 mm and 5.00 mm slice thicknesses. We performed 3-D visualizations and distance measurements with volumetric analysis software and statistically evaluated the quantitative accuracy of distance measurements. The accuracy of distance measurements on the 3-D images acquired with 1.25, 2.50, 3,75 and 5.00 mm slice thickness were 48%, 33%, 23%, 14%, respectively, and those of the reconstructed 1.25 mm were 53%, 41%, 43%, 36% respectively. Meanwhile, there were insignificant statistical differences (P-value<0.05) in the accuracy of the distance measurements of 3-D images reconstructed with 1.25 mm thickness. In conclusion, slice thickness, rather than scan mode, influenced the quantitative accuracy of distance measurements in 3-D rendered images with MDCT. The quantitative analysis of distance measurements may be a useful tool for evaluating the accuracy of 3-D rendered images used in diagnosis, surgical planning, and radiotherapeutic treatment.

• Korean Journal of Optics and Photonics
• /
• v.28 no.3
• /
• pp.108-115
• /
• 2017

We report the assembly procedure and performance evaluation of a visible and near-infrared spectrometer in the wavelength region of 400-900 nm, which is later to be combined with fore-optics (a telescope) to form a f/2.5 imaging spectrometer with a field of view of ${\pm}7.68^{\circ}$. The detector at the final image plane is a $640{\times}480$ charge-coupled device with a $24{\mu}m$ pixel size. The spectrometer is in an Offner relay configuration consisting of two concentric, spherical mirrors, the secondary of which is replaced by a convex grating mirror. A double-pass test method with an interferometer is often applied in the assembly process of precision optics, but was excluded from our study due to a large residual wavefront error (WFE) in optical design of 210 nm ($0.35{\lambda}$ at 600 nm) root-mean-square (RMS). This results in a single-path test method with a Shack-Hartmann sensor. The final assembly was tested to have a RMS WFE increase of less than 90 nm over the entire field of view, a keystone of 0.08 pixels, a smile of 1.13 pixels and a spectral resolution of 4.32 nm. During the procedure, we confirmed the validity of using a Shack-Hartmann wavefront sensor to monitor alignment in the assembly of an Offner-like spectrometer.