• Applied Chemistry for Engineering
• /
• v.1 no.2
• /
• pp.215-223
• /
• 1990

The effects of sulfur on the catalytic reaction between CO and NO on polycrystalline Pt surface, which is very important in the development of catalyst for automobile exhaust gas control, have been studied using thermal desorption spectrometry(TDS) under ultra-high vacuum(UHV) conditions. Sulfur weakened both the adsorptions of CO and NO by direct site blocking and indirect electronic effect. S(a) desorbing below 800 K gave little effect on reaction activity whereas S(a) desorbing above 800 K, which adsorbs as an atomic state, gave much effect on it. The adsorbed sulfur existed on the surface of platinum in the form of islands, and also reduced the adsorption energies of adsorbates by the long-ranged electronic effect. The platinum catalyst in the reaction between CO and NO was poisoned selectively by S(a), poisoning firstly the active sites of this reaction.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.86.2-86.2
• /
• 2011

저온형 연료전지인 직접 메탄올 연료전지(Direct Methanol Fuel Cells, DMFC)는 친환경적인 발전 시스템, 높은 에너지 효율의 장점 때문에 주목을 받고 있으나 연료극의 촉매로 사용되는 금속은 고가의 귀금속인 Pt와 Ru가 요구되어 제조비용이 비싸기 때문에 촉매의 양을 줄이고, 반응 도중 생성되는 CO에 의한 촉매의 피독 문제 등 해결하여야 할 점이 산적해 있어 연료전지 중 촉매의 활성을 높이는 연구들이 활발히 이루어지고 있다. 종래의 MEA의 촉매층 제조공정은 우선 환원석출법에 의해 Pt-Ru/C를 합성하고 Nafion 용액에 혼합하여 Pt-Ru/C 슬러리를 제조한다. 이 방법에서는 carbon sheet에 spray 방법으로 Pt-Ru/C 촉매층이 만들어지기 때문에, Pt-Ru 촉매가 Nafion에 의해 부분적으로 매몰되어 촉매의 전기화학적 활성이 떨어지는 문제점이 있다. 이를 해결하는 방안으로 펄스전류를 이용하여 Pt-Ru 합금입자를 carbon sheet에 전기화학적으로 담지 시켜 Nafion에 매몰되는 것을 방지하는 펄스전해법 연구가 진행되고 있다. 그러나 촉매의 입자크기가 일반적으로 50~70 nm 이상으 크기 때문에 촉매의 낮은 활성이 문제점으로 야기되고 있다. 본 연구에서는 Pt-Ru/C 촉매층 제조 문제점을 해결하고, 촉매의 전기화학적 활성을 증가시키기 위해서 2~4 nm Pt-Ru 콜로이드를 전해액으로 사용하고, 전기영동법을 이용하여 Pt-Ru 나노 입자를 carbon sheet($1{\times}1cm^2$) 에 담지 시켰다. 전기영동법에서 균일한 Pt-Ru 촉매층의 제조를 위해 전류인가 방법으로는 펄스전류를 사용하였고, 실험변수로는 전해액 pH, duty cycle, 담지시간을 선정하였다. 합성된 Pt-Ru 콜로이드를 TEM분석으로 나노입자의 크기와 분산성 분석하였고, 콜로이드 나노입자의 표면전하 상태를 분석하기 위해 zeta-potential을 분석하였다. Pt-Ru/C의 촉매의 전기화학적 활성을 분석하기 위하여 0.5 M H_2SO_4$ 와 1 M $CH_3OH$ 혼합용액에 CV(Cyclic Voltammetry)실시하였고, carbon sheet 전극 상 Pt-Ru의 분산성 확인을 위하여 FE-SEM분석을 수행하였다.

• Applied Chemistry for Engineering
• /
• v.23 no.1
• /
• pp.23-27
• /
• 2012

To make synthetic liquid fuel from biomass such as wood pellet, energy crop and so on, a biomass to liquid (BTL) process by using a biomass gasifier with Fisher-Tropsch (FT) reaction was developed. However $H_2S$, COS and $CO_2$ in syngas from biomass gasifiers resulted in a decrease of the conversion efficiency and the deactivation of the catalyst. To remove acid gases in syngas, a lab-scale methanol absorption tower was developed and the removal characteristics of acid gases were investigated. The methanol absorption tower efficiently removed $H_2S$ and COS with a removal of $CO_2$, so it could be useful process for the BTL process.

• Applied Chemistry for Engineering
• /
• v.31 no.5
• /
• pp.560-567
• /
• 2020

In this study, we investigated that the effect of alkali metals [Na(Sodium) and K(Potassium)], known as representative deactivating substances among exhaust gases of various industrial processes, on the NH₃-SCR (selective catalytic reduction) reaction of V/W/TiO₂ catalysts. NO, NH₃-TPD (temperature programmed desorption), DRIFT (diffuse reflectance infrared fourier transform spectroscopy analysis), and H₂-TPR analysis were performed to determine the cause of the decrease in activity. As a result, each alkali metal acts as a catalyst poisoning, reducing the amount of NH₃ adsorption, and Na and K reduce the SCR reaction by reducing the L and B acid points that contribute to the reaction activity of the catalyst. Through the H₂-TPR analysis, the alkali metal is considered to be the cause of the decrease in activity because the reduction temperature rises to a high temperature by affecting the reduction temperature of V-O-V (bridge oxygen bond) and V=O (terminal bond).

• Journal of the Korean Electrochemical Society
• /
• v.10 no.4
• /
• pp.279-282
• /
• 2007

When reformer for fuel cell is used, CO in hydrogen gas leads to a seriously decreased membrane electrode assembly (MEA) performance by catalyst poisoning. The effect of CO on performance of modified MEA by sputtering method is studied in this paper. The experimental results show that sputtered Pt and Ru thin film improve a single cell performance of MEA and sputtered metal thin film has a CO tolerance. The air injection process on anode show improved CO tolerance test result. Moreover, Pt, Ru and PtRu thin film by sputtering had influence on the CO tolerance with air injection process.

• Korean Chemical Engineering Research
• /
• v.51 no.4
• /
• pp.432-437
• /
• 2013

The CO preferential oxidation reaction (PROX) has been done using Cu catalytic active species supported on some of mesoporous silica materials which can facilitate the diffusion of the reactants in order to prevent the poisoning of anode active materials by CO molecules during driving polymer electrolyte fuel cells (PEMFC) in this study. As a result when SBA-15 with large pore used as a support showed excellent CO oxidation activity, especially the activity increased in proportion to the amount of supported Cu. Ti components which was inserted to increase the degree of dispersion of Cu, contributed to improving the performance for CO oxidation at low-temperature. The degree of dispersion of Cu ingredients was the best in the catalyst inserted 20 mol-% Ti into the framework of SBA-15, and CO oxidation activity was also improved.

• Clean Technology
• /
• v.20 no.1
• /
• pp.88-94
• /
• 2014

During the past decades much attention has been paid to the desulfurization of diesel oil which is important as a source for the fuel cells to prevent the sulfur poisoning of both diesel steam reforming catalyst and electrode of fuel cell. Although alternative desulfurization techniques have been investigated, desulfurization for ultra-low sulfur diesel (ULSD) is still challenged. Therefore, this research focuses on the desulfurization of commercial ULSD for the application to molten carbonate fuel cell (MCFC). Herein, the performances of several kinds of commercial adsorbents based on activated carbons, zeolites, and metal oxides for desulfurization of ULSD were screened. The results showed that metal oxides based materials can feasibly reduce sulfur concentration in ULSD to a level of 0.1 ppmw while activated carbons and zeolites did not reach this level at current conditions.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.10
• /
• pp.928-935
• /
• 2010

A bag filter system was partially burnt down during a trial run of waste wood incineration boiler. This brought about unburned hydrocarbon which caused a rapid deactivation of low temperature SCR catalyst set up in two stage after the bag filter. The deactivated catalyst was investigated in order to trace the origin by several characterization methods such as XRD, EDX, BET, TGA, SEM. The deactivated catalyst was regenerated by different methods such as acid washing, water washing in ultrasonication, and calcination treatment under air condition. It is found the calcination treatment under air condition at $450^{\circ}C$ for 2 hours to be the best regeneration method. The catalytic activity was measured in the form of 2 cm ${\times}$ 2 cm ${\times}$ 10 cm (catalyst weight 10 g) honeycomb type. A deNOx efficiency of the regenerated catalyst showed 100% at $180^{\circ}C$ which is the same level of fresh one.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.17-20
• /
• 2006

한국에너지기술연구원에서는 가정용 고분자연료전지 열병합 발전시스템을 위한 통합형 천연가스 연료처리 시스템을 개발해 왔다. 가정용 시스템으로서 필수적인 소형화와 고효율을 현실화하기 위해, 연료처리 시스템의 각 단위 공정 즉 수증기 개질, 수성가스 전이, 선택적 산화 공정 등을 이중 동 심관형 반응기에 통합하여 상호 열교환이 용이하도록 반응기를 설계하였다. 현재 시험 운전 중인 Prototype-I 연료 처리 시스템은 1kW급 고분자 연료전지 열병합 발전 시스템에 개질 가스를 공급하기 위해 설계되었으며, 기초 성능은 정격 부하 운전시 열효율 78% (HHV 기준), 메탄 전환율 91%이다. 개질 가스 내 일산화탄소 농도는 고분자 연료전지 전극의 피독을 피하기 위해 10ppm 이하로 유지되어야 하며, Prototype-I 연료 처리 시스템은 백금과 루테늄 촉매를 적용한 선택적 산화 반응기를 통해 개질 가스 내 일산화탄소 농도를 10ppm 이하로 제거하였다. 일반 가정에서는 고분자 연료전지 시스템의 부하 변동이 예상되기 때문에 연료 처리 시스템의 부하 변동 운전 특성도 살펴보았다 정격 부하에서 80%, 60%, 40%로 부하를 변동하며 운전하였고, 각 부하에서 안정한 메탄 전환율과 10ppm이하의 일산화탄소 농도를 보였다. 80%까지는 열효율이 77%로 큰 변화를 보이지 않았으며, 60%에서는 76%, 40%에서는 72%로 열효율이 감소하는 현상을 보였다 연료 처리 시스템의 일일 시동-정지 운전시 내구성을 테스트 중이다. 현재까지 50여회의 일일-시동 정지를 시도하였다 시동 후 약 세 시간가량의 정력 부하 운전을 실시한 후 부하 변동을 실시하였고, 총 운전 시간 8시간 정도 운전한 후 시스템을 정지하였다 메탄 전환율과 일산화 탄소 농도, 열효율을 모니터링 하고 있으며, 현재까지 초기 성능을 그대로 유지하고 있다. 앞으로 일일시동-정지 운전 시험을 지속하면서 초기 시동 특성 및 부하 변동에 따른 응답 특성 개선, 그리고 연료전지와의 연계 운전을 실시할 예정이다

• Applied Chemistry for Engineering
• /
• v.19 no.3
• /
• pp.259-263
• /
• 2008

The catalytic activity of the used catalyst, $V_2O_5/TiO_2$, for MSW incinerators was investigated focusing on its regeneration. As the result of the experimental analysis, the NOx removal efficiency difference between the fresh catalyst and used catalyst is about 60% at $260^{\circ}C$ and 1, 2-dichlorobenzen (1, 2-DCB) removal efficiency difference is about 14% at $200^{\circ}C$, in honeycomb test. And the catalysts, both the fresh and used, were characterized by XRD, TGA, and ICP techniques in order to investigate the deactivation. On the basis of the results, it is found that the used catalyst is deactivated by ammonium-sulfates, heavy metals (Pb, As etc.), alkali metals (Ca), and phase transfer of $TiO_2$. Also calcination treatment under nitrogen and air condition was excellent than washing and calcination treatment.