• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1995년도 특별강연 및 춘계학술발표 개요집
• /
• pp.99-102
• /
• 1995

• Journal of Welding and Joining
• /
• 제14권3호
• /
• pp.75-85
• /
• 1996

In this paper the influence of postweld heat treatment on mechanical properties of SMAW and FCAW stainless steel weldments was examined and the obtained results are as follows ; (1) The amount of $\delta$-ferrite formed by SMAW and FCAW process decreased with increasing holding temperature and time in post weld heat treatment(PWHT), and it was found that the reduced ferrite was transformed into sigma phase after $800^{circ}C{\times}50hr$ PWHT. This sigma phase, even though it was very small, resulted in brittleness of dissimilar weldment between carbon steel and stainless steel in bending test, however in similar weldment between stainless steel and stainless steel was not occured. (2) The chemical composition of sigma phase was measured to 28-30%Cr, 7-9%Mo, 4-6Ni in 316L weldment, and also 35-37%Cr, 0.9-1.0Mo, 6-8%Ni in 309L weldment by EDS analysis.

• 한국강구조학회 논문집
• /
• 제18권5호
• /
• pp.665-675
• /
• 2006

건출물이 고층화되고 장스팬화될 수록 고강도이면서 신뢰성이 우수한 강재의 사용요구가 증대된다. 이러한 이유로 개발된 강재가 SM570TMC 강재이다. 그러나 아직까지는 SM570TMC 강재는 우수한 기계적 성질에도 불구하고, 동급의 타 강재보다 우수하다고 하는 용접성이 검증되지 않은 상태이다. 본 연구에서는 현장 작업조건으로 국산 용접재료 2종류와 일본산 용접재료 1종류에 대해서 SA 및 FCA 용접하여 용접성을 평가하였다.

• Journal of Welding and Joining
• /
• 제13권1호
• /
• pp.127-137
• /
• 1995

The possibility of new GMAW process using economic shielding gases including CO$_{2}$ gas was investigated on the effect of shielding gas on weldabilty. In the optimum welding condition using 600A power source, FCAW process showed low depositions rate, 114 g/min at 300A, but new GMAW using other mixed shielding gases exhibited high deposition rate, 208-224 g/min at 450A. TIME gas, Ar+CO$_{2}$ gas and Ar+CO$_{2}$+O$_{2}$ gas as a shielding gas were able to be used to the very high welding current(450A), moreover TIME gas and Ar+CO$_{2}$ gas showed the highest arc stability among shielding gases studied in this experiments. The weld penetration was performed by axial spray transfer mode of weld droplet. On the basis of workability, weldability and economic point of view, Ar mixture (80%Ar+20%CO$_{2}$) gas was recommended as a shielding gas for the development and application of new GMAW process. This shielding gas showed the low spatter, good weld quality, stable arc and low cost at the region of high welding current.

• 한국산학기술학회논문지
• /
• 제6권2호
• /
• pp.122-128
• /
• 2005

본 연구에서는 구조용강 SM520을 사용하여 교량용 박스 제작시 플럭스 코어드 아크용접법에서 가스실드방식과 셀프실드방식의 두 공정으로 제작된 용접부를 건전성, 기계적 성질 및 미세조직에서 비교하였다. 그 결과 두 용접 프로세스에 의해 제작된 용접부들은 매크로 조직 및 비파괴 검사 결과 건전성이 입증되었고, 항복 및 인장강도가 각각 $462{\sim}549\;MPa$와 $548{\sim}640\;MPa$였고, CVN 충격치는 $-20^{\circ}C$에서 요구값인 40J을 충족하였다. 결과적으로, 고속철도나 고속도로 건설시 사용되는 교량용 SM520강 박스 제조시 고소 및 강풍 조건하에서 용접할 때 셀프실드 아크용접법은 기존의 가스실드 아크 용접법과 비교하여 대등한 용접 특성들을 보였기 때문에 현장 시공시 적용 타당성이 있다고 사료된다.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.365-369
• /
• 2004

Recently, Inconel 625 is used widely in offshore processing piping in order to extend the maintenance tenn and improve the quality of anti-corrosion. According to the resistance to attack in various corrosive media at temperatures from $200^{\circ}C$ to aver $1090^{\circ}C$, in combination with good low- and high-temperature mechanical strength. In general, High quality weldments for this material are readily produced by commonly used processes. in recent years, the flux cored arc welding(FCAW) process is becoming more popular due to higher deposition rate and a better weld quality as compared to the shielded metal arc welding (SMAW) process, at the same time, exhibiting equally good weld metal toughness similar to the SAW process. In this study, the weldability and weldment characteristics(mechanical properties and corrosive environment) of Inconel 625 are considered in FCAW weld associated with the several weld shielding gases($80\%Ar\;+\;20\%\;CO_2,\;50\%Ar\;+\;50\%\;CO_2,\;100\%\;CO_2$) in viewpoint of welding productivity.

• 한국해양공학회지
• /
• 제24권2호
• /
• pp.62-66
• /
• 2010

The goal of this work is to establish the reliability of FCA welded joints for high strength EH36-TMCP ultra thick plate. For this, heat conduction and thermo elasto-plastic analyses have been conducted on a multi-pass, X-groove, butt-joint model to clarify the thermal and mechanical behavior (residual stresses, magnitude of the stresses, and their production and distribution mechanisms) of the weld joint. In addition, the results of the welding residual stress obtained from thermo elasto-plastic analysis was verified and compared with results obtained by XRD analysis.

• 대한조선학회논문집
• /
• 제35권4호
• /
• pp.65-75
• /
• 1998

GMA 용접 중 100% $CO_2$ 가스를 사용하는 $CO_2$ 용접은 경제적이고 고능률적이라는 점 때문에 많이 사용되고 있다. $CO_2$ 용접의 아크현상과 스패터 발생량은 용접용 와이어의 화학성분, 실드가스, 용접조건 등에 영향을 받는다. 특히 용접조건은 용적이행 모드를 결정하기 때문에 스패터 발생량에 커다란 영향을 미친다. 본 연구는 $CO_2$ 용접 재료 중 두 type의 FCW(titania계, semi-metal계)를 이용하여 용접조건을 변화시켜 아크현상과 스패터 발생량을 파악하여 용접부의 품질 평가와 용접조건 설정에 기여코져 한다. 본 연구를 통해, 다음과 같은 결론을 얻을 수 있다. 1) 저전류 영역(140A)의 FCW 모두 22V까지는 전형적이 단락이행이 나타났고, 스패터 발생량의 증가와 저전류 스패터 입도를 대립화하였다. 2) 대전류 영역(320A)의 전형적인 globular이행에서 titania계 FCW가 semi-metal계 FCW보다 아크 안정성이 양호하였다.

• Journal of Welding and Joining
• /
• 제10권4호
• /
• pp.190-198
• /
• 1992

Among the variety of welding processes available, the flux cored arc welding is one of the most frequently used process, because of its wide range of application and high productivity. The weld joint tracking is indispensable to improve the flexibility of the arc welding robot application for the flux cored arc welding (FCAW) process. In this study, an arc sensor which utilizes the electrical signal obtained from the welding arc itself was developed for weld joint tracking in FCAW. Because a model of the welding arc in flux cored arc welding was required to develop the arc sensor, a mathematical model was proposed by analysing the welding arc behaviour, and also an experimental model by using the factorial experiment and least square method. For overcoming the fluctuation in the welding current signal during tracking the weld joint, it was fitted to a curve which is inversely proportional to a trace of tip-to-workpiece distance by using the quadratic curve-fitting method.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권4호
• /
• pp.399-406
• /
• 2005

Alloy 625 is used widely in industrial applications such as aeronautical aerospace, chemical, petrochemical and marine applications. Because of a good combination of yield strength. tensile strength, creep strength, excellent fabricability, weldability and good resistance to high temperature corrosion on prolonged exposure to aggressive environments. High qualify weldments for this material are readily produced by commonly used processes. But all of processes are not applicable to this material by reason of unavailability of matching, position or suitable welding filler metals and fluxes may limit the choice of welding processes. Recently, the flux cored wire is developed and applied for the better productivity in several welding position including the vortical position. In this study. the weldability and weldment characteristics of Alloy 625 are evaluated in FCAW weld associated with the several shielding gases($80\%Ar+20\%\;CO_2,\;50\%Ar+50\%\;CO_2.\;100\%\;CO_2$) in viewpoint of welding productivity. The results of the experimental study on corrosive characteristics of Alloy 625 are as follows; There is no remarkable difference among shielding gases. however they has a striking difference among corrosive solutions by results of distinguished density and time of corrosive solution. Generally, the shielding gases($80\%Ar+20\%\;CO_2$) was superior to the other gases on high temperature tensile and a low temperature impact. but all of the shield gases were making satisfactory results on corrosion test.