• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.97-98
• /
• 2013

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.905-906
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.397-398
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.1325-1326
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.841-842
• /
• 2008

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.893-894
• /
• 2011

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.217-220
• /
• 2003

Due to the lighter weight and the higher freedom of design than metals plastics have been spot lighted in a wide number of applications. In the making plastic parts injection-molding process is one of the most general methods. During the injection molding process, filling-packing-cooling process, plastics have exposed to several external stresses and then plastic parts injected have molding effects which are known as anisotropic properties, orientation, and residual stress. Those molding effects are often shown as unexpected phenomena which are warpage, strength decrease, stiffness reduction, etc. In case of glass fiber filed plastics these effects are more significant than the ufilled ones. Therefore the molding effects have to be considered in the parts design using glass fiber reinforced plastics. We have developed the interface program in order to consider the molding effects in structural analyses of plastic parts using Heirarchical structural searching and layer handling in direction of thickness algorithm. The advantages of this program are the freedom of FE mesh between molding and structural analysis, the variable layer to the thickness direction of parts and the conveniences of data transferring and checking

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.8
• /
• pp.50-55
• /
• 2020

This study investigates the injection molding of a plastic rack gear and focuses on deflections in the part. The causes of deflections were found and resolved through a trade-off study by injection molding analysis. Based on a warpage analysis, the fiber orientation was found to be a dominant factor in the occurrence of deflections. Changes in the part design and various injection conditions were analyzed for their effects in reducing deflections. Based on the trade-off study, a new part bottom design, injection time, and melt temperature were recommended. A trial injection was done for the new plastic rack gear, and measurements showed that its flatness surpassed that of the original part and met the specified requirement. The short injection time, low melt temperature, and symmetric similar configuration of the part contributed to the reduction in deflections. Therefore, optimized gate design and injection conditions as well as a new part design were validated through injection molding analysis in this study.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.202-203
• /
• 2014

금형 내부의 마모를 줄이기 위한 경질 박막의 안정성 향상과 표면에 인가된 압축 잔류 응력이 고주기 피로 특성에 미치는 영향을 연구하기 위해 정밀 플라스틱 사출 금형강에 주로 사용되는 Fe-3.0%Ni-0.7%Cr-1.4%Mn-X강에 스크린 질화처리와 DLC 코팅을 시간과 단일, 복합처리의 변수를 두어 코팅하였다. PAPVD법으로 DLC($3{\mu}m$), 스크린 질화(3h, $50{\mu}m$)/DLC($3{\mu}m$) 코팅 후 고주기 피로 시험을 행하여 고주기 피로 특성을 평가하였다. 스크래치 시험, 마모 시험, 잔류응력 측정을 통해 질화 처리 여부에 따른 코팅의 안정성을 평가하였다. DLC, 스크린질화/DLC 코팅한 경우 압축 잔류 응력의 영향으로 모두 피로 수명이 향상되었고 스크린질화/DLC 코팅한 경우 그 향상폭은 더 컸다. 질화 처리 후 DLC 코팅한 경우 질화층은 버퍼레이어로 작용하여 코팅의 박리를 억제함을 확인하였다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.5
• /
• pp.105-112
• /
• 2017

In this study, plastics were deformed after molding due to the characteristics of the material. The Taguchi experimental design method was utilized to find the molding conditions that minimized deformation of the plastic bezel to be assembled in an automotive steering wheel. The injection molding conditions applied to the experimental design method are the melt temperature, cavity plate coolant temperature, core plate coolant temperature, and cooling time. Each condition was divided into five levels, and a total of 25 experiments were planned. However, instead of performing 25 actual molding experiments, the injection molding analysis was performed using the Moldflow program, and the deformation values for each molding analysis were obtained. The optimal molding conditions were obtained from these deformation values. The actual injection molding experiment using optimal molding conditions was compared with the deformation amount of the current molded product. The deformation was measured using a precise 3D scanner. The deformation amount of the molded product under optimal molding conditions was 16.1% lower than the deformation amount of the current molded product.