• Computational Structural Engineering
• /
• v.26 no.4
• /
• pp.52-58
• /
• 2013

• Magazine of the Korea Concrete Institute
• /
• v.27 no.1
• /
• pp.45-48
• /
• 2015

• Magazine of the Korea Concrete Institute
• /
• v.24 no.1
• /
• pp.61-64
• /
• 2012

• Journal of the Korea Concrete Institute
• /
• v.19 no.4
• /
• pp.433-439
• /
• 2007

The main objective of the paper is to investigate the static behavior of a prestressed concrete (PSC) girder that has been spliced with precast box segments. A 20 m long full-scale spliced PSC girder is fabricated and tested to compare its static performance against a monolithic girder. The monolithic girder has the same geometric and material properties with respect to the spliced girder. This includes infernal strain, deflections, neutral axis position, and crack patterns for both girders. The test also consists of monitoring relative displacements occurring across the joints. Both the horizontal displacement (gap) and vertical displacement (sliding) are measured throughout the loading procedure. All results have been compared to those obtained from the monolithic girder. It has been demonstrated that the spliced girder offers close behavior with respect to the monolithic girder up to the crack load. Both girders exhibits ductile flexural failure rather than abrupt shear failure at joints.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.1
• /
• pp.419-424
• /
• 2012

This study is a research on the buckling analysis of a portable prestressing device using finite element analysis program, ABAQUS. In order to produce 50m-span PSC girders using pretensioning method, a portable prestressing device has to endure a large jacking force about 10MN. Therefore it shall be safe and stable about the jacking force. In this study, the buckling analysis technique is developed and the buckling analysis of a portable prestressing device is performed using previous studies about the analytical model that the validity of the analytical model was demonstrated by comparing analytical results with experimental results. The stability of the device to produce 10m span PSC girders is investigated.

• Proceedings of the KAIS Fall Conference
• /
• 2010.11a
• /
• pp.461-465
• /
• 2010

본 연구는 유한요소해석프로그램(ABAQUS)을 사용하여 이동식 긴장대의 좌굴해석 기법을 연구한 것이다. 50m에 달하는 프리텐션 방식의 PSC 거더를 제작하기 위해서는 약 10MN에 이르는 매우 큰 긴장력이 가해져 이동식 긴장대가 콘크리트 양생전까지 이 긴장력을 저항하여야 한다. 따라서 이동식 긴장대는 좌굴에 대한 안정성을 확보하여야 한다. 이에 본 논문에서는 앞서 개발한 이동식 긴장대의 해석모델을 이용하여 좌굴해석 기법에 대해 연구하여 이동식 긴장대가 좌굴에 대한 안정성 확보 여부를 파악하고자 하였다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.28 no.6
• /
• pp.699-706
• /
• 2015

This paper presents results of one-year monitoring on prestressing force of a 7-wire steel post-tensioning strand which is installed in a UHPC(ultra high performance concrete) bridge with 11.0 m long, 5.0 m wide, and 0.6 m high by using a FBG-encapsulated 7-wire steel strand. The initial prestressing forces and the prestress changes during a vehicle load test were measured using the FBG-encapsulated strand. The results show that the FBG-encapsulated 7-wire strand is very effective for monitoring the prestress forces even the change in the tension force is very small. Additionally, it was indicated that selection of the thermal expansion coefficient which is used for the temperature correction shall be carefully carried out.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.28 no.2
• /
• pp.53-60
• /
• 2024

Prestressed concrete (PSC) bridges are vulnerable to corrosion and fracture of tendons, and in particular, structures using the internal post-tensioned with grouted system have difficulties in maintenance due to limitations of inspection. In this study, the actual behavior of PSC I girder bridge was analyzed according to tendon damage. The target PSC I girder bridge, an decommissioned highway bridge of upper and lower bridges, had the service period of 33 years and 20 years, respectively. Deflection and concrete strain were measured according to the location of damaged tendon and loading method. Regardless of the age of the bridge, its structural performance decreased when the damaged tendon was closer to the center of the girder. The change in behavior increased as the truck load approached to the girder where the tendon cut. If the load was applied to the adjacent girder where the tendon was cut, the structural performance was likely to be maintained due to the influence of the entire structural system. The change in deflection was difficult to observe visually, while the concrete strain exceeded the cracking strain. Therefore, it is recommended that future monitoring and inspection of PSC I girder bridges should focus on concrete strain or cracking.

• Journal of the Korea Concrete Institute
• /
• v.24 no.6
• /
• pp.727-735
• /
• 2012

Recently, a high-strength strand of 2400 MPa was developed using domestic technologies. In 2011, KS D 7002 was revised to cover the newly developed high-strength strands to support their practical usage. Presently, however, discussions and evaluations are not sufficient on the mechanical properties of the strands and their performance in structural members. Also, there were no detailed reviews on the need to revise the current design code for practical use of the high-strength strands. In this study, flexural behavior of a member with the high-strength strands was estimated through sectional analysis and a review and comparison of the domestic and foreign design codes were conducted considering the analysis results. Also, the need for the revision of the design code was discussed. Such discussion especially focused on the estimation of the stress in strand, which related with various issues such as determination methods for yield point of strands, time-dependent loss of prestressing force, estimation of stress in strand at member failure, and net strain limit for ductile failure of member. The discussion revealed that some parts in the design code need a revision and the further studies are required.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.5A
• /
• pp.841-848
• /
• 2006

There is a complex variation of stress in PSC anchorage zones and box girder diaphragms because of large concentrated load by prestress. According to the AASHTO LFRD design code, three-dimensional effects due to concentrated jacking loads shall be investigated using three-dimensional analysis procedures or may be approximated by considering separate submodels for two or more planes. In this case, the interaction of the submodels should be considered, and the model loads and results should be consistent. However, box girder diaphragms are 3-dimensional disturbed region which requires a fully three-dimensional model, and two-dimensional models are not satisfactory to model the flow of forces in diaphragms. In this study, the strengths of the prestressed box girder diaphragms are predicted using the 3-dimensional grid strut-tie model approach, which were tested to failure in University of Texas. According to the analysis results, the 3-dimensional strut-tie model approach can be possibly applied to the analysis and design of PSC box girder anchorage zones as a reasonable computer-aided approach with satisfied accuracy.