• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.12
• /
• pp.121-126
• /
• 1997

The use of CBN tool material has been greatly increased because of the superior metal cutting performance for the machining of hardened steel. This paper presents some experimental results on the ball endmiling of harened steels. Three different hardnesses of STD11 workpieces were machined using CBN ball endimills, and the machining characteristics including cutting forces tool wear, and surface roughness of machined surface were compared. It has been found that the CBN ball endmill works better in the machining of harder workpieces. The microscopic examination explains that this unusual phenomenon is caused by the difference of microstructure of each workpieces.

• Journal of the KSME
• /
• v.20 no.6
• /
• pp.474-488
• /
• 1980

이제까지의 결과를 종합하여 보면 다음과 같은 결론을 얻을 수 있다. 1. 국산 비피막공구는 의 산에 비하여 많은 절삭영역에서 양호한 성능을 가지고 있다. 2. 국산 비피막공구 W2는 중간 절 삭 영역에서 국산 W1과 외산 W3, W4보다 우수한 성능을 나타낸다. 3. W1은 저속이거나 절삭 깊이가 클 때, W2보다 좋은 성능을 가진다. 4. W1은 대체로 플랭크 마모에 의하여, W2는 저속. 저이송에서는 프랭크마모 그리고 그밖의 영역에서는 크레이터 마모에 의하여 수명이 결정된다. 5. 국산 피막공구 CW7은 외산 CW10, 13에 비하여 내마모성이 매우 좋다. 6. 중간절삭영역에서 W 2의 표면조도는 W1, W3, W4에 비하여 훨씬 좋다. 7. 피막층 유무와 피막재질에 따른 국산 및 외산의 절삭력 차이는 거의 없다.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.3
• /
• pp.141-149
• /
• 1996

마모된 공구로 절삭을 할 때 공구가 받는 힘은 칩을 제거할 때 받는 칩 제거력과 프랭크 면에 작용하는 공구와 공작물 사이의 마찰력으로 나눌 수 있다. 칩제거력은 그 힘이 전단선의 길이와 비례함을 이용하여 계산하였고, 프랭크면에 작용하는 마찰력은 공구에 작용하는 공작물의 탄성력을 고려하여 계산하였다. 절삭력은 이 두 힘의 합으로 구해졌으며 이 계산된 힘은 실제 절삭을 하는 동안 얻어진 실험결과와 비교되었다.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.6
• /
• pp.86-97
• /
• 1994

An experimental investigation is reported on the wear mechanism of CBN cutting tools. The cutting experiments were conducted on a lathe equipped with a tool dynamometer for cutting force measurement. The investigation of wear mechanism was executed by observing the worn tools using tool microscope and scanning electron microscope. Results indicate that the flank wear occurs dominantly by abrasive wear mode and the crater wear by adhesive wear mode. The results also indicate that the width of flank wear is closely related with the passive component of cutting force.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.2
• /
• pp.28-34
• /
• 2008

Recently, with the development of high speed machining technology for difficult-cutting materials, to improve the cutting performance of cutting tool, fine surface finish of complex shape tools using magnetic polishing technology is in high demand. This study is, therefore, discussed and compared the cutting characteristics of polished tools by the adopted various magnetic polishing moving types a point of view the cutting forces and the tool life. Moreover, the practicality of magnetic polished tools in the wide range cutting conditions is investigated. From obtained results, It is confirmed that the CW(clockwise) revolution and oscillation type as the polishing moving type is proper and magnetic polished tool shows the excellence in high cutting speed range.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.3
• /
• pp.31-37
• /
• 2011

The purpose of this study is to investigate cutting characteristics and wear behavior in SCM440 steel with different cutting tools, CBN(Cubic Boron Nitride) and coated CBN. During the test coated CBN tool especially with TiAlN showed better wear resistance behavior than orginal CBN tools. In the interrupted cutting condition, axial groove affected tool surface with impact force during the turning operation. For advantageous turning parameter in the interrupted process it is recommendable that lower speed. Also surface roughness showed better behavior in the coated CBN tool conditions than normal CBN conditions. Mainly this is caused by reduced friction between material and tool surface with coated layer.