• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.605-610
• /
• 2000

A series of wind tunnel test were conducted on Korean high speed train model to understand the flow physics around the vehicle related to the aerodynamic drag. For the wind tunnel test on high-speed ground vehicle, a moving ground simulation is necessary to predict the aerodynamic drag accurately. So, the models were tested in three wind tunnels with various ground simulation facility including moving belt ground plane system and tangential blowing system. The test results including measured aerodynamic drag and flow visualization showed that a tangential blowing method can be an alternative ground simulation method in short time using conventional wind tunnel.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.10
• /
• pp.810-815
• /
• 2008

To enhance aerodynamic efficiency of the Smart Un-manned Aerial Vehicle(SUAV) during the transition period, wingtip fence is attached at the end of wing. The application of wingtip fence is to reduce the effect of the separated flow caused by the nacelle on the wing especially when the tilting angle of nacelle is more than 30 degrees. To compare the effect of with and without wingtip fence, flow visualization and measurement of the aerodynamic coefficients using the pyramidal type external balance are done. Result of forces and moments measurement shows that the slope of lift coefficient is increased 18% and rolling moment of SUAV especially 60 & 90-degree tilting is changed in favorable manners with wingtip fence.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.488-491
• /
• 2010

본 논문에서는 돌풍응답경감제어 효과 검증을 위한 풍동시험에 사용될 유연날개에 대해 공탄성 모델, 조종면 작동기 모델, 돌풍 모델 등으로 구성되는 서보공탄성 모델링을 수행하였으며, 이에 대한 연속돌풍 응답해석을 수행하여 상용 Solver를 이용한 해석결과와 비교하여 구성된 서보공탄성 모델을 검증하였다. 또한, 유연날개의 돌풍응답을 경감하는 조종면 제어기를 설계하고, 이에 대한 수치 시뮬레이션을 수행하여 돌풍응답 경감효과를 검증하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.9
• /
• pp.721-727
• /
• 2021

In this paper, aerodynamic characteristics of missile configuration with various grid fins in subsonic flow. To investigate the effects of grid fin shape, four types of experimental models were used. In addition, to examine aerodynamic characteristics of missile configurations with various grid fins according to effects of Reynolds numbers and configurations of grid fins, 6-components aerodynamic forces and moments were measured by internal balance in wind tunnel test.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1993.04a
• /
• pp.35-39
• /
• 1993

항공기의 플러터 현상을 예방키 위한 개발시의 주요 공학적 임무로는 플러 터 해석, 풍동 플러터 시험, 실기체에 대한 지상진동시험 및 비행 플러터 시 험이 있다. 이들 업무는 군용 항공기의 경우에는 군사 규격서, 민간 항공기 의 경우는 FAR 규정 등에 항공기 개발 및 개조시에는 필히 수행토록 명시 되어 있으며, 특히 개발항공기의 인증을 받기 위해서는 초도 비행전까지 필 수적으로 완료되어야 하는 업무이다. 이중 항공기 지상진동시험은 개발항공 기의 초도 비행전에 실기체를 대상으로 하는 구조 동특성 규명시험으로써 플러터 해석 모델의 정확도를 입증하고 그 해석모델을 수정하거나 개선시키 는데 필요한 구조의 동특성 변수들을 실험적으로 규명하는 시험이다. 이 시 험은 개발된 항공기의 초도비행허가를 획득하고 비행속도제한을 설정키 위 해서 초도비행 직전에 초도 개발 비행기를 대상으로 필수적으로 수행되어야 하는 필수적 시험이다. 이에 따라 개발된 항공기의 전기체 지상진동시험을 수행하였고, 시험데이터의 모달해석을 하였다. 이 시험을 수행하기 위해 3개 의 가진기를 사용하였고, 모두 159개의 지점에서 주파수응답 함수를 얻었다. 최대 48 채널의 데이터 획득시스템을 사용하였으므로, 네번에 걸쳐 측정위치 를 옮겨 전체데이타를 획득하였다. 지상진동 시험의 최종해석 결과는 유한요 소 모델의 유효성을 검토하는데 사용되었고, 시험 데이타를 이용한 가진응답 해석(Forced Response Analysis)을 통하여 비행플러터 시험시에 사용되는 플러터 가진기의 위치선정 및 가진력의 크기를 결정하는데 이용하였다.ncy)가 저주 파수대로 천이(Lower Shift)하는 현상이 나타났으며, 일정한 작업량이라도 작업중량을 줄이고 작업 빈도를 높여서 작업할 경우에 이러한 현상이 더욱 두드러졌다. 작업시간의 경과에 따른 MVIS의 감소 현상은 작업빈도가 높고 비대칭형 작업일 때 가장 크게 나타났다. 총손실을 줄이고, 상대적 비용절감효과를 갖게할 수 있다고 하였다. 따라서 본 연구에서는 성인 여성기성복의 치수적합성을 높이기위하여 출산 후 중년에 접어 들면서 체형이 변화되는 것을 고려하여 연령을 분류하고(18세-34세, 30세-51세), 각 연령 집단에 따른 체형을 각각 3가지로 분류하였다. 이에 따라 의복 생산시의 총손실을 줄이기위한 상의, 하의생산시 필요한 부위별 최적규격치 간격을 제시하였다.적인 기능으로 보여지는 것에 좁혀서 작업능력의 연령증가 변화에 대하여다원적 평가를 하는 것이 실제적이라고 할 수 있다. 따라서 본 연구에서는 인간이 가지고 있는 다수의 기능중에서 수지교 치성과 연령증가와의 관계를 조사한다. 만약 연령증가 만으로 수지교치성을 평가 할 수 없는 경우에는 어떠한 요인이 수지기민성의 변화에 영향을 미치는가를 검토한다.t list)에서 자동적으로 사건들의 순서가 결정되도록 확장하였으며, 설비 제어방식에 있어서도 FIFO, LIFO, 우선 순위 방식등을 선택할 수 있도록 확장하였다. SIMPLE는 자료구조 및 프로그램이 공개되어 있으므로 프로그래머가 원하는 기능을 쉽게 추가할 수 있는 장점도 있다. 아울러 SMPLE에서 새로이 추가된 자료구조와 함수 및 설비제어 방식등을 활용하여 실제 중형급 시스

• Aerospace Engineering and Technology
• /
• v.3 no.2
• /
• pp.217-228
• /
• 2004

This paper presents the rotating test techniques and the results of the roating test of the small-scaled hingeless rotor system with composite paddle blades in hover and forward flight conditions. The small-scaled rotor system was designed using froude-scaled properties of full scale rotor system. Metal flexures and composite flexures were made as hub flexures by the same dynamic properties of rotor system. The rotating tests of hingeless rotor system installed in GSRTS at KARI were carried out to get lead-lag damping ratios and aerodynamic loads of the hingeless rotor system. MBA(Moving Block Analysis) technique was used for the estimation of lead-lag damping ratio. 6-components balance was installed between hub and main shaft and straingauges on blades were instrumented for the measurements of aerodynamic loads of rotor system. Tests were performed on the ground and in the wind tunnel according to the test conditions of hover and forward flight, respectively.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.9
• /
• pp.759-768
• /
• 2016

Design and performance analysis of propeller for solar-powered HALE UAV, EAV-3 are conducted. Experiment points of design variables are obtained by using Design of Experiment(DOE) and Kriging meta-model is generated for objective and constraints function. The geometry of propeller is designed by evaluating the response surface with requirement and restrictions. The validity of the design is verified by meta-model based optimization. Computational analyses are carried out by using commercial CFD code and the results are compared with those from a design code and wind tunnel test. The results showed good agreement with predictions of the design code at the design altitude. Also, it is confirmed that the blockage effect due to the measurement device and support strut is included in the test data and the results including this effect compare well with the test data.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.1
• /
• pp.1-9
• /
• 2018

Lambda wing type Unmanned Combat Aerial Vehicle(UCAV) which adopts Blended Wing Body(BWB) has relatively less drag and more stealth performance than conventional aircraft. However, Pitching moment is rapidly increased at a specific angle of attack affected by leading edge vortex due to leading edge sweep angle. Wind tunnel testing and numerical analysis were carried out with UCAV 1303 configuration on condition of 50 m/s of flow velocity, $-4^{\circ}{\sim}28^{\circ}$ of the range of angle-of-attack. The effect of wing twist for longitudinal stability at the various angles of attack was verified in this study. When negative twist is applied on the wing, Pitch-break was onset at higher angle of attack due to delayed flow separation on outboard of the wing. On the other hand, pitch-break was onset at lower angle of attack and lift-to-drag ratio was increased when positive twist is applied on the wing.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.3
• /
• pp.232-242
• /
• 2015

For stealth performance consideration, many UAV designs are adopting tailless lambda-shaped configurations which are likely to have unsteady dynamic characteristics. In order to control such UAVs through automatic flight control system, more accurate estimation of dynamic stability derivatives becomes essential. In this paper, dynamic stability derivatives of a tailless lambda-shaped UAV are estimated through numerically simulated forced oscillation method incorporating dynamic mesh technique. First, the methodology is validated by benchmarking the CFD results against previously published experimental results of the Standard Dynamics Model(SDM). The dependency of initial angle of attack, oscillation frequency and oscillation magnitude on the dynamic stability derivatives of a tailless UAV configuration is then studied. The results show reasonable agreements with experimental reference data and prove the validity and efficiency of the concept of using CFD to estimate the dynamic derivatives.

• Journal of the Korean Society for Railway
• /
• v.19 no.1
• /
• pp.11-19
• /
• 2016

The flows around a high speed train are very important because they could affect the aerodynamic characteristics such as drag and acoustic noise. Especially the boundary layer of flows could represent the characteristic of flows around the high speed train. Most previous studies have focused on the boundary layer region along the train length direction for the side of the train and underbody. The measurement and analysis of the boundary layer for the roof side is also very important because it could determine the flow inlet condition for the pantograph. In this study, the roof boundary layer was measured with a 1/20 scaled model of the next generation high speed train, and the results were compared with full-scaled computational fluid dynamics results to confirm their validity. As a result, it was confirmed that the flow inlet condition for the pantograph is about 85% of the train speed. Additionally, the characteristics of the boundary layer, which increases along the train direction, was also analyzed.