• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.1
• /
• pp.329-336
• /
• 2013

The infrastructure of flexible pavement is composed of aggregate subbase, anti-frost layer, and subgrade. In particular, the subgrade performance is affected by climates such as frost action and precipitation. The method of TDR(Time Domain Reflectometry) sensors to measure moisture contents in subgrade layer has been used in the research. Due to the TDR method using dielectric permitivity of soil and water, the sensors can be affected by the low subgrade temperatures. The air temperatures frequently drops below $-20^{\circ}C$ in the winter in Korea. As a result, it is necessary to estimate the accuracy of the TDR moisture sensors in the range of below zero temperatures. In this study, the subgrade temperatures of lower than $-2^{\circ}C$ were extended to evaluate temperature sensitivity of the TDR moisture sensors. The test results revealed that the moisture contents around the sensors were reduced while those of the upper part of specimen showed a tendency to increase as the specimen surface temperature drops below zero under the volumetric moisture contents(VMC) of 20% and 30%. However, the impact of temperature on the function of the sensor at lower water contents was found to be negligible if any.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.2
• /
• pp.374-384
• /
• 2016

Concern about air pollution is gradually rising up in domestic and foreign, automotive and fuel researchers are trying to reduce vehicle exhaust emissions, through a lot of approaches, which consist of new engine design and innovative after-treatment systems, using clean (eco-friendly alternative) fuels and fuel quality improvement. This research is proceeding by two main issues : exhaust emissions and PM particle emissions of gasoline vehicle. Exhaust emissions, non-regulated emissions and PM (particulate matter) particles of automotive are causing many problems which ambient pollution and harmful effects on the human body. The main particulate fraction of automotive exhaust emissions consists of small particles. Because of their small size, inhaled particles can easily penetrate deep into the lungs. The rough surfaces of these particles make it easier for them to combine with other toxins in the environment. Thus, the hazards of particle inhalation are increased. Based on the oxygenated fuel additive types (MTBE, Bio-ETBE, Bio-ethanol, Bio-butanol), this paper discussed the influence of oxygen contents on gasoline vehicle exhaust emissions, non-regulated emissions and nano-particle emissions. Also, this paper assessed exhaust emission characteristics at 2 type test modes. The test modes were FTP-75 and HWFET. All measurement items be verified less than the value of regulated emissions. It could be known difference increase and decrease by each measurement item depending on increase the oxygen contents.

• Journal of Environmental Policy
• /
• v.12 no.1
• /
• pp.37-58
• /
• 2013

In recently, the low impact development(LID) is discussed at various fields being related to urban stormwater, non-point source pollution, and quality of life. It is understood as an integrated development tool to induce sustainable development with various value-social, economic, and aesthetic. As concerning the development of waterfront area, the low impact development is interested in environmental planning. But the planning process and factors are not considered in precedent research. This study has two purposes. The one is to understand the planning process and factors of low impact development from literature review. The other is to apply the planning factors using case study and to know the effect of low impact development as the simulation plan. The simulation plan is based on some landuse planning. It is divided into the setting the region for environmental protection and the function of public facilities, spatial planning for enlarging permeable area, and spatial planning for circulation of water. The simulation model uses the LIDMOD2. The 14 planning factors of low impact development is applied to case region. And the effect is about 7~10 percent in reduction of nonpoint source pollution and surface runoff.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.2 no.1
• /
• pp.20-28
• /
• 1999

Nine soil media when placed over a plastic sheet with three seeding rates were evaluated for influence on covering rate, height, growth, surface hardness, tear strength and sod establishment of Kentucky bluegrass. 1. Bark, peat and vermiculite over a plastic sheet had good effect in terms of the establishment of Kentucky bluegrass sod. 2. The good establishment of Kentucky bluegrass sod grown on bark, peat and vermiculite over a plastic sheet seemed to be caused by physical and chemical properties of each soil medium. 3. Sand, sandy loam, perlite and peatmoss caused poor effects on the covering rate, the growth, and the tear strength of Kentucky bluegrass. 4. Optimum seeding rate was $10g/m^2$ in terms of density and competition. 5. Good quality sod more depended on soil media than on seeding rates in this study.

• Applied Chemistry for Engineering
• /
• v.9 no.1
• /
• pp.44-51
• /
• 1998

In this work, the in-situ viscoelastic characteristics of electropolymerized polypyrrole (PPy) thin film were investigated in the electrolyte solutions of $NaClO_4$, $LiClO_4$, and $KClO_4$ by using quartz crystal analyzer (QCA). One side of quartz crystal was used as a working electrode mounted in a special fabricated QCA electrochemical ceil. The resonant frequency and resonant resistance diagram (F-R diagram) was used to interpret the viscoelastic characteristics of Pby thin film and compared with AFM photograph. The resonant frequency, resonant resistance, and current were measured to analyze the redox reaction behaviors when the cyclic voltammetry was performed using AT-cut quartz crystal electrode coated with galvanostatically polymerized Ppy film. The result suggests that the Ppy film polymerized onto the crystal behaves as a rigid elastic layer at the initial stage of electropolymerization, while the film becomes a viscoelastic layer the polymerization proceeds further. At the same time, the film thickness increases and some morphological changes take place due to the penetration of electrolyte solution into the film. These phenomena take place when cyclic voltammetry was performed using different electrolyte solution compared with polymerization process.

• Analytical Science and Technology
• /
• v.25 no.6
• /
• pp.476-482
• /
• 2012

Asian dust particles are known to have sizes ranging from a few nanometers up to about a few micrometers. The environmental and health effects depend on the size of the dust particles. The smaller, the farther they are transported, and the deeper they penetrate into the human respiratory system. Sedimentation field-flow fractionation (SdFFF) provides separation of nano to microparticles using a combination of centrifugal force and parabolic laminar flow in a channel. In this study, the steric mode of SdFFF (Sd/StFFF) was tested for size-based separation and characterization of Asian dust particles. Various SdFFF experimental parameters including flow rate, stop-flow time and field strength of the centrifugal field were optimized for the size analysis of Asian dust. The Sd/StFFF calibration curve showed a good linearity with $R^2$ value of 0.9983, and results showed an excellent capability of Sd/StFFF for a size-based separation of micron-sized particles.The optical microscopy (OM) was also used to study the size and the shape of the dust particles. The size distributions of the samples collected during a thick dust period were shifted towards larger sizes than those of the samples collected during thin dust periods. It was also observed that size distribution of the sample collected during dry period shifts further towards larger sizes than that of the samples collected during raining period, suggesting the sizes of the dust particle decrease during raining periods as the components adsorbed on the surface of the dust particles were removed by the rain water. Results show Sd/StFFFis a useful tool for size characterization of environmental particles such as the Asian dust.

• Korean Journal of Soil Science and Fertilizer
• /
• v.20 no.1
• /
• pp.29-34
• /
• 1987

This experiment was designed to find out the effects of soil conditioner, Polyacrylamide (PAM) and Bitumen, on the changes of soil aggregate properties and crop yields. The soil conditioners were treated at the rates of 0.5% and 1% to sandy loam and silty clay loam soils. The aggregate stability, wetting angle, mean weight diameter and air permeability were analyzed. Pot experiments were carried out to investigate the soybean growths and soil property changes after the soil conditioners were sprayed to surface soils. Soil aggregate stability was increased remarkably by the soil conditioner, PAM and Bitumen, treatments. PAM was more effective in sandy loam than silty clay loam, but Bitumen was better in silty clay loam. Wetting angle of the soil was changed slightly by PAM treatment, but it was greatly changed to hydrophobic by Bitumen treatment. Air permeability, water infiltration rate and moisture retention of the soils were increased by surface application of soil conditioners, PAM and Bitumen. The growths of soybean in conditioner applicated pots were better than those of untreated pots from early stage, and the yields were increased 6-13%.

• Journal of Life Science
• /
• v.21 no.5
• /
• pp.713-719
• /
• 2011

In this study, we evaluated whether Lunasin Enriched Soybean (LES) suppressed 1-chloro-2,4-dinitrochlorobenzene (DNCB) induced allergic contact dermatitis in vivo. In the group treated with DNCB alone, erythema and hemorrhage in the skin were observed, while the application of LES after DNCB treatment modulated erythema and hemorrhage similar to the untreated group. In histopathological analysis of the skin, DNCB-treated groups showed increased skin thickness compared to the untreated groups, while the treatment of LES dose-dependently modulated skin thickness. Also, hypertrophy and hyperkeratosis of the epidermis, intracellular edema and infiltration of inflammatory cells were observed in the group treated with DNCB alone, while treatment of LES inhibited these inflammatory changes. DNCB also induced a significant up-regulation of iNOS and COX-2 expression, as compared to the untreated groups. However, the treatment of LES significantly decreased the down-regulation of iNOS and COX-2 expression, as compared to DNCB-treated groups. Also, LES reduced the IgE level in DNCB-stimulated groups. And lunasin from LES translocated the nucleus of the cells in the skin of Sprague-Dawley rats. Taken together, it is thought that LES has the potential to be used as an alternative treatment for allergic contact dermatitis.

• Journal of the Korea Concrete Institute
• /
• v.17 no.1 s.85
• /
• pp.3-10
• /
• 2005

The purpose of this study is to investigate the properties of composite systems using polymer cement and epoxy resins for waterproofing and anti-corrosion to concrete structures such as water supply facilities and sewage-works. For the waterproofing and anti-corrosion of concrete structures, there can be required various properties such as absorption capacity and water permeability, adhesion and tensile strength, hair crack-resistance, impact-resistance, repeated low and high temperature test and chemical resistance, soundness for drinking water, soundness for drinking water and etc. In this study these engineering properties of composite systems using polymer-modified mortar and epoxy resins were examined and could be confirmed to satisfy the guidelines of KS. Especially, it was turn out that the adhesion properties was excellent and high crack-resistance up to 1.49 mm will be perform.

• The Korean Journal of Rheology
• /
• v.10 no.4
• /
• pp.185-194
• /
• 1998

Flow-induced voids during resin impregnation and poor fiber wetting give serious effects on the mechanical properties of composites in resin transfer molding process. In order to better understand the characteristics of resin flow and to investigate the mechanism of void formation, flow visualization experiment for the resin impregnation was carried out on plain weaving glass fiber mats using silicon oils with various viscosity values. The permeability and the capillary pressure for the fiber mats of different porosities were obtained by measuring the penetration length of the resin with time and with various injection pressure. At low porosity and low operating pressure, the capillary pressure played a significant role in impregnation process. Video-assisted microscopy was used in taking the magnified photograph of the flow front of the resin to investigate the effect of the capillary pressure on the void formation. The results showed that the voids were formed easily when the capillary pressure was relatively high. No voids were detected above the critical capillary number of 2.75$\times$$10^{-3}, and below the critical number the void content increased exponentially with decrease of the capillary number. The content of void formed was independent of the viscosity of the resin. For a given capillary number, the void content reduced with the lower porosity of the fiber mat.