• Food Science and Preservation
• /
• v.10 no.2
• /
• pp.192-199
• /
• 2003

To prepare soybean curd utilizing effectively bioactive component of soybean, ultra fine whole soybean flour(UFWSF) was used as a soybean curd material for preparation of uncompressed whole soybean flour curd(UWSFC) in this study. The UWSFC was made with treatment by proteinase and coagulant, and proximate composition, color, textural properties and sensory evaluation of that were analyzed. Protease produced from Aspergillus sojae, bromelain and papain showed soybean curd coagulation ability and the pretense produced from Aspergillus sojae showed the highest soybean curd coagulation ability. When, after first heating and homogenizing, the proteinase was added to soybean milt textural properties of UWSFC were the best. Hunter's L and b values and textural properties (hardness, fracturability springiness, gumminess and chewiness) of UWSFC using proteinase and coagulant were higher than commercial soft soybean curd and adhesiveness and cohesiveness showed contrary tendency.

• Journal of Biomedical Engineering Research
• /
• v.20 no.1
• /
• pp.37-44
• /
• 1999

Because of bone resorption, wear of ultra-high molecular weight polyethylene(UHMWPE) in total knee arthroplasty has been recognized as a major factor in long-term failure of knee implant. The surface damage and the following harmful wear debris of UHMWPE is largely related to contact stress. Most of the previous studies focused on the contact condition only at the articulating surface of UHMWPE. Recently, contact stress at the metal-backing interface has been implicated as one of major factors in UHMWPE wear. Therefore, the purpose of the is study is to investigate the effect of the contact stress for different thickness, conformity friction coefficient, and flexion degree of the UHMWPE component in total knee system, considering the contact conditions at both interfaces. In this study, a two-dimensional non-linear plane strain finite element model was developed. The results showed that the maximum value of von-Mises stress occurred below the articulating surface and the contact stress was lower for the more conforming models. All-polyethylene component showed lower stress distribution than the metal-backed component. With increased friction coefficient on the tibiofemoral contact surface, the maximum shear stress increased about twofold.

• Journal of Conservation Science
• /
• v.31 no.1
• /
• pp.1-11
• /
• 2015

Seated Amitabha Triad at Muwisa Temple (Treasure No. 1312) had been known as wooden Buddha statue, but a precise safety inspection revealed that the statue is terracotta Buddha statue made with clay. The clay layer of Amitabha Triad was conserved due to its severe damage. In this study, experiments were conducted to produce the most appropriate filler for the conservation treatment of the seated Amitabha Triad. Mixed clay samples with various ratios were produced and surface hardening state, crack, color change, and shrinkage of the samples during dry process were measured. Loess, fine sand powder, and cotton were used to produce the mixed clay for the filler with six different ratios and then 12 different concentration glues made with glutinous rice glue, Pachymeniopsis Elliptica glue, and animal glue were added as adhesives. Total 72 types of samples were prepared and comparative study was conducted. As a result, when the mixed clay contains 2.5% cotton compared to the weight per cent of loess and fine sand powder and also loess and fine sand in the mixed clay have a 15:1 ratio, the mixed clay had the lowest shrinkage. Animal glue is considered as an appropriate glue since it had small color change, low physical property change and shringkage. Therefore, mixed clay (loess:fine sand=15:1) mixed with 15ml animal glue is likely to be a suitable filler for conservation treatment of the seated amitabha triad at the Muwisa Temple.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.12
• /
• pp.1063-1069
• /
• 2012

In present paper, we used magnesium alloy having a lower density and higher electrical conductivity for bipolar plate to reduce the weight of PEM fuel cell. The silver was coated to prevent corrosion and form passivation film on the metal surface with sputtering. In acid proof evaluation for setting optimal coating conditions, the homogeneity of coating thickness was improved by coating with the thickness of 3 ${\mu}m$ which not indicated any micro cracks and the temperature $180^{\circ}C$. The performance test and evaluation based on the clamping pressure and channel depth to determine the configuration of bipolar plate for assembling single cell was implemented. And then we assembled single cell with this bipolar plate and implemented the performance test to ensure and compare the current-voltage performance followed as several factors such as coating or non-coating, the change of clamping pressure, the change of channel depth, etc. As these results, the maximum power density of single cell with the coated bipolar plate was 192 $mW/cm^2$ and it was confirmed that the power density per unit mass was better than existing metal bipolar plate.

• International Journal of Highway Engineering
• /
• v.12 no.3
• /
• pp.27-35
• /
• 2010

Asphalt Plug Joint(APJ) is an buried expansion joint that enabling the smooth connection of expansion gap and road pavement by filling the gap with bituminous mixture of 20% bitumen and 80% aggregate by weight, so it secures evenness and expansion or contraction using the material's properties. Although APJ is designed to have a 6-7 year lifecycle, there are some cases where it is damaged within the first six months. This early damage cause traffic congestion due to frequent repair works, and social cost exceeding the installation cost of the joint. So, in this research, we have developed a new system of Buried Folding Lattice Joint(BFLJ) which can overcome the disadvantages of APJ, and have analyzed and compared it's performance with the conventional APJ through experiment with specimens. As a result of the experiment, APJ had crack formation on both ends of the gap plate, spreading to the surface of the expansion joint. With this result, we can conclude that the reason for early damage is the tension failure due to the concentration of strain in the asphalt mixture along the end of gap plate and the debonding along the joint section. In contrast, the newly developed BFLJ induced even transformation in the joint by applying moving stud and high performance material, and resolved APJ's disadvantage of strain concentration. Therefore, it could be seen that the newly developed BFLJ could overcome the disadvantages of APJ and prevent early damage.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.455-455
• /
• 2010

차세대 디스플레이로 널리 알려져 있는 플렉서블 디스플레이는 휴대하기 쉽고, 깨지지 않으며, 변형이 자유로워 현재 우리 사회에 크게 주목받고 있다. 플렉서블 디스플레이의 구현을 위해서는 기존의 유리 기반 디스플레이 소자 기술에 더하여 플렉서블 기판소재에 적용 가능한 투명전도막 기술의 확립이 필요하다. 디스플레이 산업에서 주로 사용되는 투명전도막은 ITO (indium tin oxide) 및 IZO (indium zinc oxide)와 같은 투명전도성 산화물 박막 (TCO, transparent conducting oxide)이다. 그런데 플라스틱 기판이 굽힘 환경에 놓이게 되면 그 위에 증착된 산화물 박막이 쉽게 파손될 수 있다. 따라서 플렉서블 디스플레이 기술에 있어서 변형에 따른 TCO 박막의 파괴 거동에 대한 연구가 필수적이다. 본 연구에서는 PET (polyethylene terephthalate) 기판 상에 증착된 IZO 박막의 반복 굽힘 시 계면구조 변화에 따른 파괴거동을 조사하였다. 플라스틱 기판의 사용을 위해서는 산소 및 수분의 투과 방지막이 필요하며 본 연구에서는 투과 방지막 (또는 보호막)으로서 $SiO_x$ 박막을 적용하였다. IZO 박막은 $In_2O_3$ - 10 wt% ZnO 타겟을 사용하여 RF magnetron sputtering법으로 $100^{\circ}C$ 미만에서 저온 증착하였다. 보호막으로 사용되는 $SiO_x$ 박막은 HMDSO (hexamethyldisiloxane)와 Ar 및 $O_2$ 혼합기체를 이용하는 PECVD 방법으로 합성하였다. 변형에 따른 TCO 박막의 파괴 거동을 조사하기 위하여 반복 굽힘 시험 (cyclic- bending test)을 실시하였다. 반복 굽힘 시험 중 실시간으로 IZO 박막의 전기저항 변화를 측정하여 박막의 파괴 거동을 모니터링 하였다. 시편 A (135 nm-thick IZO/PET), B (135 nm-thick IZO/ 90 nm-thick $SiO_x$/PET), C (135nm-thick IZO/ 300 nm-thick $SiO_x$/PET)에 대하여 곡지름 35mm, 1000회 반복 굽힘을 실시하여 변형 중의 전기저항 변화를 조사하였다. 그리고 굽힘 시험 완료 후, FE-SEM을 이용한 시편 표면형상 관찰을 통하여 균열생성 정도를 관찰하였다. 반복 굽힘 시험 결과, A 와 C 시편의 경우, 각각 반복 굽힘 20회, 550회에서 급격한 전기저항의 증가가 관찰되었다. 그러나 B 시편의 경우, 1000회 반복 굽힘 후에도 전기저항의 변화는 나타나지 않았다. 이와 같이 반복 굽힘에 의한 IZO 박막의 파괴 거동 변화는 IZO 박막과 기판의 계면구조변화에 기인한 것으로 해석된다. IZO 박막과 기판의 계면에 $SiO_x$ 층을 삽입함으로써 계면 접합강도가 향상되었을 것으로 추측된다. 따라서 변형에 대한 파괴 저항 특성이 우수한 투명전도성 산화물 박막의 형성을 위해서는 적절한 계면구조 제어를 통한 계면 접합 특성의 향상이 필요하다.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.36 no.1
• /
• pp.34-40
• /
• 2016

The objective of this study was to determine the effect of moisture content on the physical and chemical characteristics of Italian ryegrass cube. Cube quality according to moisture contents (15, 20, 25, and 30%) was determined. Cubes made with 15 to 20% moisture showed a little cracks. But, the amount of powder generate from these cubes were lower by 10 to 16% compared to other cubes made with 25 to 30% moisture contents. The highest hardness at 159 kg/f was obtained when the cube was made with 15% moisture content and the lowest was 70 kg/f when the cube was made with 30% moisture content. The electrical loading and surface temperature were increased when moisture content was decreased. The chemical compositions of cube were differ from those of raw materials. Crude protein (CP) and ether extract (EE) contents were increased after cubing works. However, crude fiber (CF), acid detergent fiber (ADF), and neutral detergent fiber (NDF) contents were decreased after cubing. The crude ash content was not significantly (p > 0.05) different between raw material and cube. Higher moisture content resulted in higher crude protein content. However, crude fiber and crude ash content were not significantly (p > 0.05) different between each other. The contents of ADF and NDF were the lowest in cubes made with 30% moisture content. Our results suggest that the proper moisture content of Italian ryegrass cubing is recommended to be 15 to 20% and that cubing works should help increase forage quality.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.4
• /
• pp.569-577
• /
• 2021

CFRP(Carbon Fiber Reinforced Plastic) can maintain the same strength even if the diameter is reduced by about one - third, and the weight is about one - twentieth of that of the deformed reinforcing bars that have been used in the construction industry. In particular, it is resistant to corrosion, which is the weakest part of reinf orcing bars, and there is no concern that it will deteriorate over time, It is light and durable, so transportation costs are low and it is convenient for high-rise buildings. This paper experimentally clarifies the adhesive properties of CFRP and clarifies its behavior. That is, bond strength test was conducted with the directness of CFRP and the strength of concrete as experimental variables, and the bond mechanism was clarified experimentally. Furthermore, based on the experimental results, we constructed the bond stress-slip-strain relationship of CFRP compared to the existing deformed reinforcing bars.

• Korean Journal of Heritage: History & Science
• /
• v.44 no.3
• /
• pp.92-111
• /
• 2011

This study focus on the restoration stone selection of break-out part based on material characteristics analysis and the conservational safety diagnosis using various nondestructive techniques for Jungdong and Banjukdong Stone Auariums. As a result, the original rocks of the stone aquariums body are porphyritic granodiorite with magnetite-series having igneous lineation, microcline phenocryst, veinlet and basic xenolith. As a result of the provenance presumption of the host rock, a rock around Gamgokri area in Nonsan City was identified the genetically same rock. Therefore, the rock is appropriate for restoration materials of the break-out part. The deterioration assessment showed that the stone aquariums were highly serious scaling, scale off and blackening. Particularly, the front face of Banjukdong stone aquarium needs reinforcement of structural crack (760mm) caused from igneous lineation of biotite. Blackening contaminants on the stone aquariums surface occurred by combining iron oxide, manganese oxide and clay mineral. Also, major factors of efflorescence contaminants were identified as calcite (Jungdong stone aquariums) and gypsum (Banjukdong stone aquariums). The physical characteristics of stone aquariums appeared that the original and new stone is third (moderately weathered) and second grade (slightly weathered), respectively. This study sets up an integrated conservation system from material analysis to restoration stone selection and conservational safety diagnosis of Jungdong and Banjukdong stone aquariums.

• Conservation Science in Museum
• /
• v.25
• /
• pp.85-94
• /
• 2021

Conservation treatment of metallic artifacts contaminated with corrosion and foreign substances requires changes in the shape, characteristics, weight and thickness of the artifacts. Thus far, recording the changes after conservation treatment has mainly been performed through visual observation and photography, which lacks any quantitative description of the changes. In this study, the processes of removing foreign substances, joining cracks, and restoring an affected area were recorded using 3D scanning and then quantitatively analyzed to identify changes in form due to conservation treatment. The volume change after the conservation process was calculated based on the results of the 3D scanning, and numerical data on the changes to the form was analyzed. It was revealed that the foreign or corroded substances removed after the conservation accounted for 18.1 cm³, which is approximately 52% of the total volume of the ring pommel, and those substances were removed from about 98% of the surface of the ring pommel. This study confirmed that 3D form analysis was useful for recording the processes of conservation treatment and analyzing the results. It is therefore believed that this methodology can be applicable to not only metal artifacts, but to cultural heritage items in a range of materials.